DOI QR코드

DOI QR Code

메인롤을 이용한 대형 형상링롤링의 예비성형체 연구

Preform design of large sized profile ring rolling using main roll

  • 투고 : 2013.07.12
  • 심사 : 2013.11.02
  • 발행 : 2014.01.01

초록

본 연구는 외경부에 단이 존재하는 제품의 링롤링작업을 위한 예비성형체의 설계에 관한 연구이다. 형상링롤링 공정에서 가장 일반적으로 나타나는 결함 중 하나는 미충진이며, 변형량이 적을 경우나 외경부 단의 깊이가 클 경우 발생한다. 이러한 미충진을 방지하기 위해서는 변형량을 증가시키거나 예비성형체를 최종형상에 근접하도록 설계하여야 한다. 결함이 없는 제품을 생산하기 위하여 형상비와 성형비를 이용한 충진한계식을 제안하였다. 충진한계식은 네가지 경우에 대하여 유한요소해석과 시험생산한 결과를 토대로 작성되었다. 실물 크기의 형상링롤링 작업을 수행하고 충진한계식을 이용한 예측과 비교함으로써 제안된 방법의 타당성을 검증하였다.

This paper introduces a preform design method for a ring rolling process with an outer step. Underfilling is one of the general defects of the profile ring rolling process. It occurs when the deformation amount is small or step depth of the profiled region is large. To prevent underfilling, increasing the deformation amount or using a preform of size similar to that of the final product are required. Furthermore, the filling limit equation is suggested based on the shape factor and deformation ratio for preventing defects in the products. The filling limit equation has been derived through finite element analyses and production tests for four different cases. For verifying the suggested method, realsized profile rolling tests were performed, and test results were compared with the predictions of the equation.

키워드

참고문헌

  1. Shivpuri, R. and Eruc, E., 1993, "Planning and Simulation of the Ring Rolling Process for Improved Productivity," International Journal of Machine Tools and Manufacturing, Vol.33, No.2, pp.153-173. https://doi.org/10.1016/0890-6955(93)90071-2
  2. Johnson, W. and Needham, G., 1968, "Experiments on Ring Rolling," International Journal of Mechanical Sciences, Vol.10, pp.95-113. https://doi.org/10.1016/0020-7403(68)90066-0
  3. Mamalis, A.G., Hawkyard, J.B. and Honson, W., 1976, "Spread and Flow Patterns in Ring Rolling," International Journal of Mechanical Sciences, Vol.18, pp.11-16. https://doi.org/10.1016/0020-7403(76)90069-2
  4. Yang, D.Y. and Kim, K.H., 1988, "Rigid-Plastic Finite Element Analysis of Plain Strain Ring Rolling," International Journal of Mechanical Sciences, Vol.30, No8, pp.571-580. https://doi.org/10.1016/0020-7403(88)90100-2
  5. Kim, N.S., Machida, S. and Kobayashi, S., 1990, "Ring Rolling Simulation by the Three Dimensional Finite Element Method," International Journal of Mechanical Science, Vol.30, No.4, pp.569-577.
  6. Cho, S.H. and Kim, N.S., 1992, "Experimental Analysis of Ring Rolling," Transactions Korean Society of Mechanical Engineering, Conf.(1), pp.360-363.
  7. Joun, M.S., Chung, J.H. and Shivpuri, R., 1998, "An Axisymmetric Forging Approach to Perform Design in Ring Rolling Using a Rigid-Viscoplastic Finite Element Method," International Journal of Machine Tools and Manufacture, Vol.38, No.10-11, (October 1998), pp. 1183-1191. https://doi.org/10.1016/S0890-6955(98)00014-5
  8. Nam, Y.G., Kim, S.Y., Jeon, C.H., Sung, K.J. and Moon, Y.H., 2011,"A Study on Optimization of Blank Dimension According to Target Ring Dimension in Ring Rolling Process," Transactions Korean Society of Mechanical Engineering, Conf.(1), pp.63-66.
  9. Davey, K. and Ward, M.J., 2002, "The Practicalities of Ring Rolling Simulation for Profiled Rings," Journal of Materials Processing Technology, Vol.125-126, pp.619-625. https://doi.org/10.1016/S0924-0136(02)00356-4
  10. Kim, K.H., Suk, H.G. and Huh, M.Y., 2007,"Development of the Profile Ring Rolling Process for Large Slewing Rings of Alloy Steels," Journal of Materials Processing Technology, Vol.187-188, pp.730-733. https://doi.org/10.1016/j.jmatprotec.2006.11.040
  11. Hua, L., Qian, D.S. and Pan, L.B., 2009, "Deformation Behaviors and Conditions in L-Section Profile Cold Ring Rolling," Journal of Materials Processing Technology, Vol.209, pp.5087-5096. https://doi.org/10.1016/j.jmatprotec.2009.02.007
  12. Wang, L.G., Zhang, Y.F. and Wu, J.S., 2010, "Simulation and Test on Rolling Pairs of Large Wind-Tower Flange," China International Forge Master, pp.69 - 73.