DOI QR코드

DOI QR Code

Application of Spray Pyrolysis Process for the Preparation of Nano Sized Cobalt Oxide Powder

  • Kim, Dong Hee (Department of Anesthesiology, Dankook University) ;
  • Seo, Dong Jun (Department of Advanced Materials Engineering, Hoseo University) ;
  • Yu, Jae Keun (Department of Advanced Materials Engineering, Hoseo University)
  • Received : 2013.12.01
  • Accepted : 2013.12.10
  • Published : 2014.01.27

Abstract

In this study, nano-sized cobalt oxide powder with an average particle size below 50 nm was prepared from a cobalt chloride solution by the spray pyrolysis process. The influences of reaction temperature on the properties of the generated powder were examined. The average particle size of the particles formed based on the spray pyrolysis process at a reaction temperature of $700^{\circ}C$ is roughly 20 nm. Moreover, most of these particles cannot appear with an independent type, thereby coexisting in a droplet type. When the reaction temperature increases to $800^{\circ}C$, the average particle size not only increases to roughly 40 nm but also shows a more dense structure while the ratio of particles which shows a polygonal form significantly increases. As the reaction temperature increases to $900^{\circ}C$, the distribution of the particles is from roughly 70 nm to 100 nm, while most of the particle surface is more intricately close and forms a polygonal shape. When the reaction temperature increases to $1000^{\circ}C$, the particle size distribution of the powder shows an existing form from 80 nm to at least 150 nm in an uneven form. As the reaction temperature increases, the XRD peak intensity gradually increases, yet the specific surface area gradually decreases.

Keywords

References

  1. T. Nakamura and Y. Okano, Proceeding of the ICF 7, C1-101 (1996).
  2. C. P. Udawatte and K. Yanagisawa, J. Am. Ceram. Soc., 84(1), 251 (2001). https://doi.org/10.1111/j.1151-2916.2001.tb00645.x
  3. J. K. Yu and D. H. Kim, Kor. J. Mater. Res., 23(2), 81 (2013) https://doi.org/10.3740/MRSK.2013.23.2.081
  4. J. K. Yu and D. H. Kim, Powder Tech., 235(2), 1030 (2013) https://doi.org/10.1016/j.powtec.2012.11.031
  5. J. K. Yu and D. H. Kim, J. of Nanosci. Nanotechnol., 12(2), 1545 (2012) https://doi.org/10.1166/jnn.2012.4625
  6. J. K. Yu and D. H. Kim, J. Ceram. Soc. Jpn., 117(10), 1078 (2009). https://doi.org/10.2109/jcersj2.117.1078
  7. J. K. Yu, S. G. Kang, K. C. Chung. J. S. Han and D. H. Kim, Mater. Trans., 48(2), 249 (2007). https://doi.org/10.2320/matertrans.48.249
  8. J. K. Yu, S. G. Kang, J. B. Kim, J. Y. Kim, J. S. Han, J. W. Yoo, S. W. Lee and Z. S. Ahn, Mater. Trans., 47(7), 1838 (2006). https://doi.org/10.2320/matertrans.47.1838
  9. J. K. Yu, K. W. Kim, T. S. Kim and J. Y. Kim, Mater. Trans., 46(7),1695 (2005). https://doi.org/10.2320/matertrans.46.1695
  10. D. Majumdar, T. A. Shefelbine and T. T. Kodas, J. Mater. Res., 11(11), 2861 (1996). https://doi.org/10.1557/JMR.1996.0361
  11. T. C. Pluym and T. T. Kodas, J. Mater. Res., 10(7), 1661 (1995). https://doi.org/10.1557/JMR.1995.1661
  12. G. L. Messing, S. C. Zhang and G. V. Jayanthi, J. Am. Ceram. Soc,. 76(11), 2707 (1993). https://doi.org/10.1111/j.1151-2916.1993.tb04007.x
  13. I. Barin: Thermochemical Data of Pure Substances, VCH, Germany, 1392-1404 (1989).

Cited by

  1. Effect of Inflow Rate of Raw Material Solution on the Fabrication of Nano-Sized Cobalt Oxide Powder by Spray Pyrolysis Process vol.26, pp.11, 2016, https://doi.org/10.3740/MRSK.2016.26.11.662