DOI QR코드

DOI QR Code

Convective heat transfer of MWCNT / HT-B Oil nanofluid inside micro-fin helical tubes under uniform wall temperature condition

  • Kazemia, M.H. (School of Mechanical Engineering, College of Engineering, University of Tehran) ;
  • Akhavan-Behabadi, M.A. (School of Mechanical Engineering, College of Engineering, University of Tehran) ;
  • Nasr, M. (School of Mechanical Engineering, College of Engineering, University of Tehran)
  • 투고 : 2013.03.07
  • 심사 : 2014.05.12
  • 발행 : 2014.06.25

초록

Experiments are performed to investigate the single-phase flow heat transfer augmentation of MWCNT/HT-B Oil in both smooth and micro-fin helical tubes with constant wall temperature. The tests in laminar regime were carried out in helical tubes with three curvature ratios of 2R/d=22.1, 26.3 and 30.4. Flow Reynolds number varied from 170 to 1800 resulting in laminar flow regime. The effect of some parameters such as the nanoparticles concentration, the dimensionless curvature radius (2R/d) and the Reynolds number on heat transfer was investigated for the laminar flow regime. The weight fraction of nanoparticles in base fluid was less than 0.4%. Within the applied range of Reynolds number, results indicated that for smooth helical tube the addition of nanoparticles to the base fluid enhanced heat transfer remarkably. However, compared to the smooth helical tube, the average heat transfer augmentation ratio for finned tube was small and about 17%. Also, by increasing the weight fraction of nanoparticles in micro-fin helical tubes, no substantial changes were observed in the rate of heat transfer enhancement.

키워드

참고문헌

  1. Akhavan Behanadi, M.A, Fakour Pakdaman, M. and Ghazvini, M. (2012), "Experimental investigation on the convective heat transfer of nanofluid flow inside vertical helically coiled tubes under uniform wall temperature condition", Int. J. Commun. Heat Mass Transfer., 39, 556-564. https://doi.org/10.1016/j.icheatmasstransfer.2012.02.008
  2. Chen, H. and Zhang, B. (2003), "Fluid flow and mixed convection heat transfer in a rotating curved pipe", Int. J. Thermal Sci., 42, 61-72.
  3. Choi, S.U.S. and Eastman, J.A. (1995), "Enhancing thermal conductivity of fluids with nanparticles", Proceedings of the 1995 International Mechanical Engineering Congress and Exhibition, San Francisco, November.
  4. Fakour Pakdaman, M., Akhavan-Behabadi, M.A. and Razi, P. (2012), "An experimental investigation on thermo-physical properties and overall performance of MWCNT/heat transfer oil nanofluid flow inside vertical helically coiled tubes", Exper. J. Therm. Fluid Sci., 40, 103-111. https://doi.org/10.1016/j.expthermflusci.2012.02.005
  5. Ghobadi, M. and Muzychka, Y.S. (2013), "Effect of entrance region and curvature on heat transfer in mini scale curved tubing at constant wall temperature", Int. J. Heat Mass Transfer, 65, 357-365. https://doi.org/10.1016/j.ijheatmasstransfer.2013.05.078
  6. Godson, L., Raja, B., Mohan Lal, D. and Wongwises, S. (2010) "Enhancement of heat transfer using nanofluids - an overview", Renew. Sustain. Energy Rev., 14(2), 629-641. https://doi.org/10.1016/j.rser.2009.10.004
  7. Heris, S.Z., Etemad, S.Gh. and Esfahany, M.N. (2006) "Experimental investigation of oxide nanofluids laminar flow convective heat transfer", Int. J. Heat Mass Transfer, 33(4), 529-535. https://doi.org/10.1016/j.icheatmasstransfer.2006.01.005
  8. Hwang, K.S., Jang, S.P. and Choi, S.U.S. (2009), "Flow and convective heat transfer characteristics of water-based $Al_{2}O_{3}$ nanofluids in fully developed laminar flow regime", Int. J. Heat and Mass Transfer, 52, 193-199. https://doi.org/10.1016/j.ijheatmasstransfer.2008.06.032
  9. Kays, W. and Cawford, M. (1993), Convective Heat and Mass Transfer, 3rd Edition, McGraw-Hill, New York, NY, USA.
  10. Lee, S., Choi, S.U.S., Li, S. and Eastman, J.A. (1999), "Measuring thermal conductivity of fluids containing oxide nanoparticles", J. Heat Transfer, 121, 280-289. https://doi.org/10.1115/1.2825978
  11. Mansour, B.R., Galanis, N. and Nguyen, C.T. (2011), "Experimental study of mixed convection with water- $Al_{2}O_{3}$ nanofluid in inclined tube with uniform wall heat flux", Int. J. Thermal Sci., 50, 403-410. https://doi.org/10.1016/j.ijthermalsci.2010.03.016
  12. Naphon, P. (2011), "Study on the heat transfer and flow characteristics in a spiral coil tube", Int. Commun. Heat Mass Transfer, 38, 69-74. https://doi.org/10.1016/j.icheatmasstransfer.2010.10.007
  13. Salimpour, (2008), "Heat transfer characteristic of a temperature-dependent-property fluid in shell and coiled tube heat exchangers", Int. J. Commun. Heat Mass Transfer, 35(9), 1190-1195 https://doi.org/10.1016/j.icheatmasstransfer.2008.07.002
  14. Sillekens, J.J.M., Rindt, C.C.M. and Van Steenhoven, A.A. (1998), "Developing mixed convection in a coiled heat exchanger", Int. J. Heat Mass Transfer, 41, 61-72. https://doi.org/10.1016/S0017-9310(97)00111-7
  15. Xin, R.C. and Ebadian, M.A. (1997), "The effects of Prandtl numbers on local and average convective heat transfer characteristics in helical pipes", J. Heat Transfer, 119, 463-7.
  16. Yang, G., Dong, F. and Ebadian, M.A. (1995), "Laminar forced convection in a helicoidal pipe with finite pitch", Int. J. Heat Mass Transfer, 38, 853-62. https://doi.org/10.1016/0017-9310(94)00199-6

피인용 문헌

  1. Pressure Drop and Heat Transfer Characteristics of MWCNT/Heat Transfer Oil Nanofluid Flow inside Microfinned Helical Tubes with Constant Wall Temperature vol.622-623, pp.1662-8985, 2012, https://doi.org/10.4028/www.scientific.net/AMR.622-623.796
  2. Effect of high energy ball milling on the structure of iron - multiwall carbon nanotubes (MWCNT) composite vol.6, pp.3, 2017, https://doi.org/10.12989/amr.2017.6.3.245