Journal of the Korean Society of Manufacturing Process Engineers (한국기계가공학회지)

The Korean Society of Manufacturing Process Engineers (한국기계가공학회)
권호 표지
DOI QR코드

DOI QR Code

Effects of Ultrasonic Vibration on Machined Surface of Aluminium 6061 in Endmill Cutting Process

Al6061의 엔드밀 절삭가공에서 초음파 진동이 가공 표면에 미치는 영향

  • Received : 2014.06.11
  • Accepted : 2014.06.20
  • Published : 2014.06.30
Download PDF
⟨ Previous Next ⟩

Abstract

This study focused on the effects of ultrasonic vibration on a machined surface of Al6061 material in the endmill cutting process. It is known that ultrasonic vibration greatly increases the efficiency of the machining process when cutting or grinding. An ultrasonic vibration table was developed for application to ultrasonic vibration endmill machining experiments.Inthisstudy,the surface roughness and actual depth of the cut measured confirm the effects of ultrasonic vibration. As a result of the experiments, the actual depth of the cut increased during endmill machining when using ultrasonic vibration. The surface roughness was improved with increases in the amplitude of the vibration and the depth of the cut.

Keywords

References

  1. Ratmond, G. O.,"Comparison of stress-relife procedures for cryogenic aluminum mirrors," NASA Tech., Report No. 20020061280, pp. 57-70, 2002.
  2. Joo, H. Y. and Lee, Y. S., "A study on Residual stress at Cutting work," J. of KSMTE, Vol. 6 No. 3, pp. 111-117, 1997.
  3. Kang, J. P., Kim, B. H. and Song, J. B.,"A Study on the Improvement of Cutting Precision by the Ultrasonic Vibration Cutting," J. of KSPE, Vol. 8 No. 2, pp. 69-77, 1991.
  4. Kim, N. H., "Selection of the Optimal Machining Condition for a High-hardness Resin using the 5-axis Machine," J. of KSMPE, Vol. 11 No.5, pp. 29-34, 2012.
  5. Kim, H. T. and Shin, K. H.,"A Study on the Effects of Feed rate and Shotpeening on the Fatigue Life of Al7075-T6 Specimens," Transactions of KSMTE, Vol. 16 No. 4, pp. 64-70, 2007.
  6. Song, Y. C., Kenichi, T. and Toshimichi, M., "Mirror Finishing of Co-Cr-Mo Alloy by Ultrasonic Elliptical Vibration Cutting Method," J. of KSPE, Vol. 25 No. 3, pp. 56-62, 2008.
  7. Kim, K. D. and Lee, K. H., "Development of Excitation Table for 2-dimensional Vibrational Micro Cutting," J. of KSMPE, Vol. 11 No. 3, pp. 62-67, 2012.
  8. Song, Y. C. and Park, C. H.,"Ultra-precision Cutting of Polycarbonate for Optical Components by Using Elliptical Vibration Cutting Method," J. of KSPE, Vol. 26 No. 6, pp. 42-49, 2009.
  9. Kim, K. D., Loh, B. G. and Kim, J. S., "Development of Ultra-Precision Ultrasonic Surface Machining Device Using Cyclic Elliptical Cutting Motion of a Couple of Piezoelectric Material," J. of KSMPE, Vol. 5 No. 3, pp. 29-35, 2006.

Cited by

  1. Experimental Verification of Characteristics of Magnetic Abrasive Polishing Combined with Ultrasonic Vibration vol.39, pp.9, 2015, https://doi.org/10.3795/KSME-A.2015.39.9.923
  2. 초음파 적외선열화상 기법을 적용한 모터 코어의 신뢰성 평가 vol.15, pp.4, 2016, https://doi.org/10.14775/ksmpe.2016.15.4.060
  3. A Study on Fracture Characteristics in Opening Mode of a DCB Specimen Using a Lightweight Material vol.20, pp.1, 2014, https://doi.org/10.14775/ksmpe.2021.20.01.042
  4. Fracture Characteristic of Double Cantilever Beam Specimen Using Lightweight Material at Sliding Mode vol.20, pp.3, 2014, https://doi.org/10.14775/ksmpe.2021.20.03.016
  5. Adhesive Fracture Characteristic of DCB Specimen due to Single and Heterogeneous Materials under Tearing Load vol.20, pp.4, 2014, https://doi.org/10.14775/ksmpe.2021.20.04.127