Journal of the Korean Ceramic Society (한국세라믹학회지)

The Korean Ceramic Society (한국세라믹학회)
권호 표지
DOI QR코드

DOI QR Code

Effect of Screen Printing and Sintering Conditions on Properties of Thick Film Resistor on AlN Substrate

인쇄 및 소결조건이 AlN 기판용 후막저항체의 특성에 미치는 영향

  • Koo, Bon Keup (Department of Materials Science and Engineering, Hanbat National University)
  • Received : 2014.05.01
  • Accepted : 2014.06.11
  • Published : 2014.07.31
Download PDF
⟨ Previous Next ⟩

Abstract

$RuO_2$-based high frequency thick-film resistor paste was printed at the speed of 10, 100, 300 mm/sec on the AlN substrate, and then sintered at between 750 and $900^{\circ}C$. The sintered thick films were characterized in terms of printing and sintering conditions. With increasing printing speed, the thickness and roughness of sintered film increased. The resistance of the thick film resistor was reduced by increasing the printing speed from 10 to 100 mm/sec, but did not significantly change at 300 mm/sec speed. With increasing sintering temperature, the surface roughness and thickness of sintered resistor film decreased. The reduction rate was large in case of fast printed resistor. The resistance of the resistor increased up to $800^{\circ}C$ with sintering temperature, but again decreased at the higher sintering temperature.

Keywords

References

  1. X. Zhou, M. Sazegar, F. Stemme, J. Haußelt, R. Jakoby, and J. R. Binder, "Correlation of the Microstructure and Microwave Properties of $Ba_{0.6}Sr_{0.4}TiO_3$ Thick-films," J. Eur. Ceram. Soc., 32 [16] 4311-18 (2012). https://doi.org/10.1016/j.jeurceramsoc.2012.06.021
  2. J. Gondek and J. Kocol, "New Hybrid with Q-factor-passband Microwave Filter Constructed with Dielectric Resonators and Coupled with a Thick-film Microstrip Line Made in Miamond Substrates," Diamond Relat. Mater., 10 [8] 1511-14 (2001). https://doi.org/10.1016/S0925-9635(00)00618-X
  3. B. Su, J. E. Holmes, C. Meggs, and T. W. Button, "Dielectrics and Microwave Properties of Barium Strontium Titanate Thick Films on Alumina Substrate," J. Eur. Ceram. Soc., 23 [14] 2699-703 (2003). https://doi.org/10.1016/S0955-2219(03)00171-7
  4. R. Martinez-Manez, J. Soto, E. Garcia-Breijo, L. Gil, J. Ibanez, and E. Gadea, "A Multisensor in Thick-film Technology for Water Quality Control," Sens. Actuators, A, 120 [2] 589-95 (2005). https://doi.org/10.1016/j.sna.2005.03.006
  5. D. Crescini, D. Marioli, and A. Taroni, "Low-cost Accelerometers: Two Examples in Thick-film Technology," Sens. Actuators, A, 55 [2-3] 79-85 (1996). https://doi.org/10.1016/S0924-4247(97)80060-X
  6. C. L. Yuan, X. Y. Liu, C. R. Zhou, J. W. Xu, and B. Li, "Electrical Properties of Lead-free Thick Film NTC Thermistors Based on Perovskite-type $BaCo_xCo_{2x}Bi_{1-3x}O_3$," Mater. Lett., 65 836-39 (2011). https://doi.org/10.1016/j.matlet.2010.12.013
  7. C. A. Harper, Handbook of Thick Film Hybrid Microelectronics; Ch. 3, pp. 1-47, McGRAW-Hill, New York, 1982.
  8. P. J. Holmes and R. G. Loasby, Handbook of Thick Film Technology; pp. 14-49, Electrochemical Pub. Ltd., London, 1976.
  9. M. Lahti, A. Vimpari, and Kari Kautio, "Printable Resistors in LTCC Systems," J. Eur. Ceram. Soc., 27 2953-56 (2007). https://doi.org/10.1016/j.jeurceramsoc.2006.11.046
  10. P. Barnwell and J. Wood, "Fabrication of Low Cost Microwave Circuits and Structure Using an Advanced Thick Film Technology," IEMT/IMC Symposium, 2nd, pp. 327-32, 1998.
  11. C. A. Harper, Handbook of Thick Film Hybrid Microelectronics; Ch. 6, pp. 17-21, McGRAW-Hill, New York, 1982.
  12. B. K. Koo, "Effect of Lead Free Glass Frit Compositions on Properties of Ag System Conductor and $RuO_2$ Based Resistor Pastes(in Korean)," J. of the KIEEME, 24 [3] 200-07 (2011). https://doi.org/10.4313/JKEM.2011.24.3.200

Cited by

  1. 스크린 인쇄법의 공정 조건이 전극 패턴 균일성에 미치는 영향 vol.33, pp.5, 2014, https://doi.org/10.4313/jkem.2020.33.5.355