Journal of the Korean Society of Marine Environment & Safety (해양환경안전학회지)

The Korean Society of Marine Environment and safety (해양환경안전학회)
권호 표지
DOI QR코드

DOI QR Code

Critical Elastic Buckling Load Investigation of Aluminium Alloy A6082-T6 Square plate Subjected to Patch Loading

패치 로딩을 받는 알루미늄 합금 A6082-T6 사각형 판의 임계 탄성좌굴하중 검토

  • Oh, Young-Cheol (Dep. of Ocean System Engineering, Graduate School, MMU) ;
  • Ko, Jae-Yong (Dep. of Naval Architecture & Ocean Engineering, College of Marine Technology, MMU)
  • 오영철 (목포해양대학교 대학원 해양시스템공학과) ;
  • 고재용 (목포해양대학교 해양공과대학 조선해양공학과)
  • Received : 2014.06.30
  • Accepted : 2014.08.27
  • Published : 2014.08.31
Download PDF
⟨ Previous Next ⟩

Abstract

In this paper, we examined the problem of the structural stability according to the patch load of a rectangular plate that reflects the material properties of A6082-T6 is used primarily for marine plant structure. it applied to the four patch loading shapes, the effect of aspect ratio, a boundary condition and calculated the critical elastic buckling load. Calculating the critical elastic buckling load, During the eigenvalue buckling analysis it is applied to the shell181 as 4 node shell element. when the plate subjected to patch loading compare to the plate under a uniform axial compression load, it is possible observed to occur the different elastic buckling behaviour and it could be confirmed that it is affected significantly on a variable position and type of loadings, such as the effect of the aspect ratio. Also, Critical elastic buckling load according to th patch loading type in simply supported rectangular plate a/b=1.0, ${\gamma}b$=200mm are calculated 67%(Loading type I), 119 %(Loading type II), 76 %(Loading type III), 160 %(Loading type IV), respectively. Loading type I and III could be determined with the strong elastic buckling behavior much more than Loading type II and IV.

본 연구에서 해양플랜트 구조물에 주로 사용하고 있는 알루미늄 합금 A6082-T6의 재료특성을 반영한 사각형 판에 대한 패치 로딩의 구조 안정성 문제를 검토하였다. 구조 안정성 문제를 검토 시 네 가지 패치 로딩 형태와 종횡비 효과, 주변지지조건을 적용하여 임계 탄성 좌굴하중을 산출하였다. 고유치 좌굴해석 간 사용한 요소는 4절점 쉘요소 shell181을 적용하였다. 패치 로딩을 받는 판은 균일 축 압축하중과 비교 시 상이한 탄성 좌굴거동이 발생되는 것을 관찰할 수 있었으며 하중형태와 위치, 종횡비 효과 등과 같은 변수에 대해 상당히 영향을 받고 있는 것을 확인할 수 있다. 또한, 종횡비(a/b) 1.0, 하중길이(${\gamma}b$) 200 mm 단순지지 사각형 판에서 패치 로딩 형태에 따른 임계 탄성좌굴하중은 67 %(하중 I), 119 %(하중 II), 76 %(하중 III), 160 %(하중 IV)이 각각 산출되었으며 하중 I과 III은 하중 II와 IV보다 훨씬 더 탄성 좌굴거동에 강한 것으로 판단할 수 있다.

Keywords

References

  1. ANSYS. Inc.(2000), ANSYS theory manual, Nonlinear buckling problem, Chapter 3, Part4, pp. 120-132.
  2. Gerstle, K. H.(1967), Basic Structural Design, McGraw-Hill Book Company, pp. 88-90.
  3. Kinney, J. S.(1957), Indeterminate Structural Analysis, Addison Wesley Publishing Co., pp. 1-655.
  4. Lee, S. G., S. C. Kim and J. G. Song(2001), Critical Loads of Square Plates Under Different Inplane Load Configurations on Opposite Edges, International Journal of Structural Stability and Dynamics, Vol. 1, No. 2, pp. 283-291. https://doi.org/10.1142/S0219455401000147
  5. Oh, Y. C., D. G. Bae. and J. Y. Ko(2014), Basic Research for Resistance Prediction of Aluminium Alloy Plate Girders Subjected to Patch Loading, Journal of the Korean Society of Marine Environment & Safety, Vol 20, No 2, pp. 218-227. https://doi.org/10.7837/kosomes.2014.20.2.218
  6. Patel, G. and S. K. Sahu(2006), Buckling of Curved Panels Subjected to Non-uniform Loading Using Finite Element Method, Presented in National Conference on "Emerging Trends in Nano Technology and innovations in design and manufacturing, Feb 18-19, 2006, NIT, Rourkela.
  7. Pflger, A.(1975), Stabilit atsprobleme der Elastostatik, Springer, Verlag Berlin Heidelberg New York, pp. 1-523.
  8. Shariati, M. and A. Dadrasi(2012), Numerical and Experimental Investigation of Loading Band on Buckling of Perforated Rectangular Steel Plates, Research of Journal of Recent Sciences, Vol. 1, No. 10, pp. 63-71.
  9. Singh, S., K. Kulkani, R. Pandey and H. Singh(2012), Buckling Analysis of Thin Rectangular Plates with Cutouts Subjected to Partial Eedge Compression Using FEM, Journal of Engineering, Design and Technology, Vol. 10, pp. 128-142. https://doi.org/10.1108/17260531211211935
  10. Sundaresan, P., G. Singh and V. Rao(1998), Buckling of Mooderately Thick Rectangular Composite Plates Subjected to Partial Edge Compression, Int. J. Mech. Sci. Vol. 40, No. 11, pp. 1105-1117. https://doi.org/10.1016/S0020-7403(98)00009-5
  11. Timoshenko, S. P. and J. M. Gere(1961), Theory of Elastic Stability, McGraw-Hill Book Company, pp. 1-541.