DOI QR코드

DOI QR Code

Experimental and numerical investigation of expanded metal tube absorber under axial impact loading

  • Nouri, M. Damghani (Faculty of Mechanical Engineering, Semnan University) ;
  • Hatami, H. (Faculty of Mechanical Engineering, Semnan University) ;
  • Jahromi, A. Ghodsbin (Faculty of Mechanical Engineering, Semnan University)
  • 투고 : 2014.08.21
  • 심사 : 2015.05.05
  • 발행 : 2015.06.25

초록

In this research, the cylindrical absorber made of expanded metal sheets under impact loading has been examined. Expanded metal sheets due to their low weight, effective collapse mechanism has a high energy absorption capacity. Two types of absorbers with different cells angle were examined. First, the absorber with cell angle ${\alpha}=0$ and then the absorber with angle cell ${\alpha}=90$. Experimental Study is done by drop Hammer device and numerical investigation is done by finite element of ABAQUS software. The output of device is acceleration-time Diagram which is shown by Accelerometer that is located on the picky mass. Also the output of ABAQUS software is shown by force-displacement diagram. In this research, the numerical and experimental study of the collapse type, force-displacement diagrams and effective parameters has been investigated. Similarly, the comparison between numerical and experimental results has been observed that these results are matched well with each other. From the obtained results it was observed that the absorber with cell angle ${\alpha}=0$, have symmetric collapse and had high energy absorption capacity but the absorber with cell angle ${\alpha}=90$, had global buckling and the energy absorption value was not suitable.

키워드

참고문헌

  1. ABAQUS Analysis User's Manual (2010), v6.10 Section 6.3.3, Explicit Dynamic Analysis.
  2. Alghamdi, A.A.A. (2001), "Collapsible impact energy absorbers: an overview", Thin Wall. Struct., 39, 189-213. https://doi.org/10.1016/S0263-8231(00)00048-3
  3. ANSI/ASTM A611-72 (1979), Standard Specification for STEEl, COLD-ROLLED SHEET, CARBON, STRUCTURAL.
  4. Dietenberger, M., Buyuk, M. and Kan, C.D. (2005), "Development of high strain-rate dependent vehicle model", FHWA/NHTSA National crash Analysis Center.
  5. EMMA (Expanded Metal Manufacturers Association) (2012), Division of the National Association of Architectural Metal Manufacturers (NAAM), EMMA 557-12: Standards for Expanded Metal.
  6. Ghamarian, A., Zarei, H.R. and Abadi, M.T. (2011), "Experimental and Numerical Crashworthiness Investigation of Empty and Foam-filled End-capped Conical Tubes", Thin Wall. Struct., 49(10), 1312-1319. https://doi.org/10.1016/j.tws.2011.03.005
  7. Graciano, C., Martinez, G. and Smith, D. (2009), "Experimental investigation on the axial collapse of expanded metal tubes", Thin Wall. Struct., 47, 953-961. https://doi.org/10.1016/j.tws.2009.02.002
  8. Graciano, C., Martinez, G. and Gutierrez, A. (2012), "Failure mechanism of expanded metal tubes under axial crushing", Thin Wall. Struct., 51, 20-24. https://doi.org/10.1016/j.tws.2011.11.001
  9. Gupta, N.K. and Venkatesh. (2006), "A study of the influence of diameter and wall thickness of cylindrical tubes on their axial collapse", Thin Wall. Struct., 44, 290-300. https://doi.org/10.1016/j.tws.2006.03.005
  10. Huang, M.Y., Tai, Y.S. and Hu, H.T. (2010), "Dynamic crushing characteristics of high strength steel cylinders with elliptical geometric discontinuities", Theo. Appl. Fract. Mech., 54, 44-53. https://doi.org/10.1016/j.tafmec.2010.06.014
  11. Johnson, G.R. and Cook, WH. (1983), "A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures", Proceedings of the 7th International Symposium on Ballistics, Hague, Netherlands.
  12. Jones, N. (2010), "Dynamic energy absorption and perforation of ductile structures", Int. J. Press. Vess. Pip., 87, 482-492. https://doi.org/10.1016/j.ijpvp.2010.07.004
  13. Jones, N. (2010), "Energy-absorbing effectiveness factor", Int. J. Impact Eng., 37, 754-765. https://doi.org/10.1016/j.ijimpeng.2009.01.008
  14. Li, Z., Yu, J. and Guo, L. (2012), "Deformation and energy absorption of aluminum foam-filled tubes subjected to oblique loading", Int. J. Mech. Sci., 54, 48-56. https://doi.org/10.1016/j.ijmecsci.2011.09.006
  15. Martinez, G., Graciano, C. and Teixeira, P. (2013), "Energy absorption of axially crushed expanded metal tubes", Thin Wall. Struct., 71, 134-146. https://doi.org/10.1016/j.tws.2013.05.003
  16. Nia, A.A. and Hamedani, J.H. (2010), "Comparative analysis of energy absorption and deformations of thin walled tubes with various section geometries", Thin Wall. Struct., 48, 946-954. https://doi.org/10.1016/j.tws.2010.07.003
  17. Olabi, A.G., Morris, E. and Hashmi, M.S.J. (2007), "Metallic tube type energy absorbers a synopsis", Thin Wall. Struct., 45(7-8), 706-726. https://doi.org/10.1016/j.tws.2007.05.003
  18. Qu, H., Huo, J., Xu,C. and Fu, F. (2014), "Numerical studies on dynamic behavior of tubular T-joint subjected to impact loading", Int. J. Impact Eng., 67, 12-26. https://doi.org/10.1016/j.ijimpeng.2014.01.002
  19. Smith, D., Graciano, C., Martinez, G. and Teixeira, P. (2014), "Axial crushing of flattened expanded metal tubes", Thin Wall. Struct., 85, 42-49. https://doi.org/10.1016/j.tws.2014.08.001
  20. Song, J., Chen, Y. and Lu, G. (2013), "Light-Weight thin-walled structures whit patterned windows under axial crushing", Int. J. Mech. Sci., 66, 239-248. https://doi.org/10.1016/j.ijmecsci.2012.11.014
  21. Tai, Y.S., Huang, M.Y. and Hu, H.T. (2010), "Axial compression and energy absorption characteristics of high-strength thin-walled cylinders under impact load", Theo. Appl. Fract. Mech., 53, 1-8. https://doi.org/10.1016/j.tafmec.2009.12.001
  22. Theodore, N. and Recht, R.F. (1990), High Velocity Impact Dynamics, Chapter 1 Introduction to Impact Phenomena, John Wiley and Sons, New York, NY.
  23. Zachary, A. and Ensign, K. (2005), Determination of the Constitutive Equations for 1080 Steel and Vascomax 300, Air force institute of technology, Air Force Univercity.
  24. Zhang, X., Cheng, G., You, Z. and Zhang, H. (2007), "Energy absorption of axially compressed thin-walled square tubes with patterns", Thin Wall. Struct., 45(9), 737-746. https://doi.org/10.1016/j.tws.2007.06.004

피인용 문헌

  1. Axial Crushing of Concentric Expanded Metal Tubes Under Impact Loading vol.14, pp.5, 2017, https://doi.org/10.1590/1679-78253670
  2. Numerical and Experimental Investigation of SS304L Cylindrical Shell with Cutout Under Uniaxial Cyclic Loading 2019, https://doi.org/10.1007/s40997-017-0120-2
  3. Buffering sandwiches made of thermoplastic polyurethane honeycomb grids: Manufacturing technique and property evaluations 2017, https://doi.org/10.1177/1099636217739547
  4. Energy absorption performance on multilayer expanded metal tubes under axial impact vol.116, 2017, https://doi.org/10.1016/j.tws.2017.03.005
  5. Polypropylene fiber reinforced concrete plates under fluid impact. Part I: experiments vol.60, pp.2, 2016, https://doi.org/10.12989/sem.2016.60.2.211
  6. A theoretical analysis of the energy absorption response of expanded metal tubes under impact loads vol.109, 2017, https://doi.org/10.1016/j.ijimpeng.2017.06.009
  7. Penetration performance of axisymmetric U-shape-nose grooved projectile into aluminum target: Theoretical model and experiment vol.15, pp.5, 2018, https://doi.org/10.1590/1679-78254511
  8. Experimental and numerical study on energy absorption of lattice-core sandwich beam vol.27, pp.2, 2018, https://doi.org/10.12989/scs.2018.27.2.135
  9. Damage potential: A dimensionless parameter to characterize soft aircraft impact into robust targets vol.78, pp.1, 2021, https://doi.org/10.12989/sem.2021.78.1.031
  10. Feasibility study of buckling-restrained braces with PM-35 steel core vol.79, pp.2, 2021, https://doi.org/10.12989/sem.2021.79.2.199