DOI QR코드

DOI QR Code

Fatigue behavior of circular hollow tube and wood filled circular hollow steel tube

  • Malagi, Ravindra R. (Department of PDM, Visvesvaraya Technological University) ;
  • Danawade, Bharatesh A. (Department of PDM, Visvesvaraya Technological University)
  • 투고 : 2014.02.09
  • 심사 : 2015.02.03
  • 발행 : 2015.09.25

초록

This paper presents the experimental work on fatigue life and specific fatigue strength of circular hollow sectioned steel tube and wood filled circular hollow section steel tube. Burning effect was observed in the case of circular hollow sectioned steel tube when it is subjected to Maximum bending moment of 19613.30 N-mm at 4200 rpm, but this did not happen in the case of wood filled hollow section. Statistical analysis was done based on the experimental data and relations have been built to predict the number of cycles for the applied stress or vice versa. The relations built in this paper can safely be applied for design of the fatigue life or fatigue strength of circular hollow sections and wood filled hollow sections. Results were validated by static specific bending strengths determined by ANSYS using a known applied load.

키워드

참고문헌

  1. American Society of Metals (1975), Failures of Shafts; Failure Analysis and Prevention, Metals Handbook, 10, 373-397.
  2. Amiri, M. (2010), "Rapid determination of fatigue failure based on temperature evolution", Int. J. Fatigue, 32(2), 382-389. https://doi.org/10.1016/j.ijfatigue.2009.07.015
  3. ANSYS (2010), ANSYS Inc., Release 13.0 help.
  4. ASTM E8 (2011), Standard Test Methods for Tension Testing of Metallic Materials; American Society for Testing of Materials, West Conshohocken, PA, USA.
  5. ASTM D143 (1994), Standard Method of Testing Small Clear Specimens of Timber; American Society for Testing of Materials, West Conshohocken, PA, USA.
  6. Bao, Z., Eckelman, C. and Gibson, H. (1996), "Fatigue strength and allowable design stresses for some wood composites used in furniture", Holz als Roh-und Werkstoff, 54(6), 377-382. https://doi.org/10.1007/s001070050204
  7. Berndt, F. and Van Bennekorn, A. (2001), "Pump shaft failures-a compendium of case studies", Eng. Fail. Anal., 8(2), 135-144. https://doi.org/10.1016/S1350-6307(99)00043-6
  8. Bhaumik, S.K., Rangaraju, R., Parameswara, M.A., Venkataswamy, M.A., Bhaskaran, T.A. and Krishnan, R.V. (2002), "Fatigue failure of a hollow power transmission shaft", Eng. Fail. Anal., 9(4), 457-467. https://doi.org/10.1016/S1350-6307(01)00033-4
  9. Chen, X., Jin, D. and Kim, K.S. (2006), "Fatigue life prediction of type 304 stainless steel under sequential biaxial loading", Int. J. Fatigue, 28(3), 289-299. https://doi.org/10.1016/j.ijfatigue.2005.05.003
  10. da Fonte, M. and de Freitas, M. (1999), "Stress intensity factors for semi elliptical surface cracks in round bars under bending and torsion", Int. J. Fatigue, 21(5), 457-463. https://doi.org/10.1016/S0142-1123(98)00090-5
  11. Danawade, B., Malagi, R. and Malagi, S. (2013), "Flexural strength properties of teak wood filled rectangular hollow sectioned thin steel tube and its application in automobile", SAE Technical Paper, 2013-01-1179.
  12. Dawood, M. Rizikalla, S. and Summer, E. (2007), "Fatigue and overloading beviour of steel-concrete composite flexural members strengthened with high modulus CFRP materials", J. Compos. Construct., 11(6), 659-669. https://doi.org/10.1061/(ASCE)1090-0268(2007)11:6(659)
  13. DuPont, Design guide manual 1, Dupont Engineering polymers, Reorder No.: H-76838, 70-71.
  14. Fine Testing Machines (2008), Product Catalog, Model FTG-8(D), 2008/163.
  15. Kim, Y. and Heffernan, P. (2008), "Fatigue behavior of externally strengthened concrete beams with fiber reinforced polymers: State of the art", J. Compos. Construct., 12(3), 246-256. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:3(246)
  16. Mahagaonkar, S.B., Brahmankar, P.K. and Seemikeri, C.Y. (2009), "Effect on fatigue performance of shot peened components: An analysis using DOE technique", Int. J. Fatigue, 31(4), 693-702. https://doi.org/10.1016/j.ijfatigue.2008.03.020
  17. Miscow, G.F., de Miranda, P.E.V., Netto, P.A. and Placido, J.C.R. (2004), "Techniques to characterize behavior of full size drill pipes and small scale samples", Int. J. Fatigue, 26(6), 575-584. https://doi.org/10.1016/j.ijfatigue.2003.10.014
  18. Roeder, C., Lehman, D. and Bishop, E. (2010), "Strength and stiffness of circular concrete filled tubes", J. Struct. Eng., 136(12), 1545-1553. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000263
  19. Schneider, C.R.A. and Maddox, S.J. (2003), "Best practice guide on statistical analysis of fatigue data", International Institute of Welding, IIW-XIII-WG1-114-03.
  20. Shgley, J.E., Mischke, C.R., Budynas, R.G., Liu, X. and Gao, Z. (2004), Mechanical Engineering Design, Tutorial 4-17, The McGraw Hill, New York, NY, USA, pp. 1-11.
  21. West System Inc. (2005), Fatigue, Technical Information, Catalog number , 000-545
  22. Yavari, F., Rafiee, M.A., Rafee, J., Yu, Z.-Z. and Koratkar, N. (2010), "Dramatic increase in fatigue life in hierarchical graphene composites", ACS Appl. Mater. Interf., 2(10), 2738-2743. https://doi.org/10.1021/am100728r
  23. Zhu, Z., Ahmad, I. and Mirmiran, A. (2009), "Fatigue modeling of concrete filled fiber reinforced polymer tubes", J. Compos. Construct., 13(6), 582-590. https://doi.org/10.1061/(ASCE)1090-0268(2009)13:6(582)

피인용 문헌

  1. Multi-objective durability and layout design of fabric braided braking hose in cyclic motion vol.25, pp.4, 2015, https://doi.org/10.12989/scs.2017.25.4.403
  2. Rapid S-N type life estimation for low cycle fatigue of high-strength steels at a low ambient temperature vol.33, pp.6, 2015, https://doi.org/10.12989/scs.2019.33.6.777