DOI QR코드

DOI QR Code

Adjustment of Control Limits for Geometric Charts

  • Kim, Byung Jun (Department of Statistics, Virginia Tech) ;
  • Lee, Jaeheon (Department of Applied Statistics, Chung-Ang University)
  • Received : 2015.08.19
  • Accepted : 2015.09.08
  • Published : 2015.09.30

Abstract

The geometric chart has proven more effective than Shewhart p or np charts to monitor the proportion nonconforming in high-quality processes. Implementing a geometric chart commonly requires the assumption that the in-control proportion nonconforming is known or accurately estimated. However, accurate parameter estimation is very difficult and may require a larger sample size than that available in practice in high-quality process where the proportion of nonconforming items is very small. Thus, the error in the parameter estimation increases and may lead to deterioration in the performance of the control chart if a sample size is inadequate. We suggest adjusting the control limits in order to improve the performance when a sample size is insufficient to estimate the parameter. We propose a linear function for the adjustment constant, which is a function of the sample size, the number of nonconforming items in a sample, and the false alarm rate. We also compare the performance of the geometric charts without and with adjustment using the expected value of the average run length (ARL) and the standard deviation of the ARL (SDARL).

Keywords

References

  1. Chang, T. C. and Gan, F. F. (2001). Cumulative sum charts for high yield processes, Statistica Sinica, 11, 791-805.
  2. Goh, T. N. (1987). A control chart for very high yield processes, Quality of Assurance, 13, 18-22.
  3. Goh, T. N. and Xie, M. (1994). New approach to quality in a near-zero defect environment, Total Quality Management, 5, 3-10.
  4. Jensen, W. A., Jones-Farmer, L. A., Champ, C. W. and Woodall, W. H. (2006). Effects of parameter estimation on control chart properties: A literature review, Journal of Quality Technology, 38, 349-364.
  5. Jones, M. A. and Steiner, S. H. (2012). Assessing the effect of estimation error on the risk-adjusted CUSUM chart performance, International Journal for Quality in Health Case, 24, 176-181. https://doi.org/10.1093/intqhc/mzr082
  6. Jones-Farmer, L. A.,Woodall,W. H., Steiner, S. H. and Champ, C.W. (2014). An overview of phase I analysis for process improvement and monitoring, Journal of Quality Technology, 46, 265-280. https://doi.org/10.1080/00224065.2014.11917969
  7. Lee, J., Wang, N., Xu, L., Schuh, A. and Woodall, W. H. (2013). The effect of parameter estimation on upper-sided Bernoulli CUSUM charts, Quality and Reliability Engineering International, 29, 209-223. https://doi.org/10.1002/qre.1304
  8. McCool, J. and Joyner-Motley, T. (1998). Control charts applicable when the fraction nonconforming is small, Journal of Quality Technology, 30, 240-247.
  9. Nelson, L. S. (1994). A control chart for parts-per-million nonconforming items, Journal of Quality Technology, 26, 239-240.
  10. Steiner, S. H. and MacKay, R. J. (2004). Effective monitoring of processes with parts per million defective: A hard problem!, In H. J. Lenz and P. Wilrich (Eds.), Frontiers in Statistical Quality Control 7, Physica-Verlag, Heidelberg, 140-149.
  11. Szarka, J. L. and Woodall, W. H. (2011). A review and perspective on surveillance of Bernoulli processes, Quality and Reliability Engineering International, 27, 735-752. https://doi.org/10.1002/qre.1256
  12. Tang, L. C. and Cheong,W. T. (2004). Cumulative conformance count chart with sequentially updated parameters, IIE Transactions, 36, 841-853. https://doi.org/10.1080/07408170490473024
  13. Woodall, W. H. (1997). Control charts based on attribute data: bibliography and review, Journal of Quality Technology, 29, 172-183.
  14. Xie, M. and Goh, T. N. (1997). The use of probability limits for process control based on geometric distribution, International Journal of Quality & Reliability Management, 14, 64-73. https://doi.org/10.1108/02656719710156789
  15. Yang, Z., Xie, M., Kuralmani, V. and Tsui, K.-L. (2002). On the performance of geometric charts with estimated control limits, Journal of Quality Technology, 34, 448-458.
  16. Zhang, M., Peng, Y., Schuh A., Megahed F. M. and Woodall, W. H. (2013). Geometric charts with estimated control limits, Quality and Reliability Engineering International, 29, 209-223. https://doi.org/10.1002/qre.1304