DOI QR코드

DOI QR Code

순 티타늄 박판의 파이버 레이저 용접시 결함 억제를 위한 연속의 출력 파형제어 특성(I) - 슬롭 업 & 다운 적용에 따른 영향 -

The Characteristics of Continuous Waveshape Control for the Suppression of Defects in the Fiber Laser Welding of Pure Titanium Sheet (I) - The Effect According to Applying Slope Up & Down -

  • 김종도 (한국해양대 해사대학 기관관공학부) ;
  • 김지성 (한국해양대 대학원 기관공학과)
  • Kim, Jong-Do (Division of Marine Engineering, Korea Maritime and Ocean univ.) ;
  • Kim, Ji-Sung (Graduate School, Korea Maritime and Ocean Univ.)
  • 투고 : 2016.11.11
  • 심사 : 2016.12.12
  • 발행 : 2016.12.30

초록

Laser welding has superior characteristic such as low distortion, high welding speed, easy automation and real time control. But it is easy to occur weld defects such as porosity, crater, humping bead in the area of welding start and end. These weld defects can be suppressed by applying the wave shape control. In this study CW fiber laser was used for welding of $0.5mm^t$ pure titanium. Penetration properties were evaluated with the time of slope up and down. After then the bead shape was observed, and the maximum depth and the area of crater were measured. The bead shape of welding start area changed to be sharp with increase of slope up time and non-weld area of welding start increased. The crater and humping bead were suppressed with slope down time. The cooling rate of crater area was understood through measure of the hardness. Also, The distribution tendency of alloying elements was observed by EPMA and EDS. When wave shape control didn't applied to weld, the hardness of end weld increased due to rapid cooling rate and the hardness of rear part in the crater was higher than that of fore part. On the other hand, when the wave shape control was used for end weld, the increase of hardness in the end weld couldn't be found due to gradual cooling rate.

키워드

참고문헌

  1. Jong-Do Kim, Ji-Sung Kim, The Study for Improving the Weldability of Pure Titanium Sheet by Using Fiber Laser, The Effect of Shielding Gas Nozzle Variable, J. of Welding and Joining, 34 (5) (2016), 6-12 (in Korean) https://doi.org/10.5781/JWJ.2016.34.5.6
  2. Sadek A Alber, Abass Mahmoud, Zaghloul Bahaa, Elrefaey Ahmed, Ushio Masao, Investigation of dissimilar joints between low carbon steel and Monel 400, Trans JWRI, 29 (1) (2000), 21-8
  3. Figert John, Rybicki Dan, Developing a welding procedure for joining Monel 400 to 316L stainless steel. NASA M&P Update (NMPU) NASA M&P Update Newslett, 2 (1) (1998)
  4. HIRAISHI, M., Laser Lap-Welding of Stainless Steel to Cu Alloy, Quarterly Journal of The Japan Welding Society, 17 (3) (1999), 420-425. (in Japanese) https://doi.org/10.2207/qjjws.17.420
  5. Young-Pyo Kim, Cheol-Hee Kim, Young-Gon Kim, Sung-Min Joo, Trends of Technology Development of Friction Stir Welding Machine, J. of Welding and Joining, 34 (3) (2016), 1-5 (in Korean)
  6. Jae-Do Kim, Ju-Hong Moon, C-ring stress corrosion test for Inconel 600 and Inconel 690 sleeve joint welded by Nd:YAG laser, Corrosion Science, 46 (4) (2004), 807-818 https://doi.org/10.1016/S0010-938X(03)00098-2
  7. A. Vandewynckelea, E. Vaamondea, M. Fontana, P. Herwigb, A. Masciolettic, Laser welding head tailored to tube-sheet joint requirements for heat exchangers manufacturing, Physics Procedia, 41 (2013), 144-152 https://doi.org/10.1016/j.phpro.2013.03.063
  8. Hossain Ebrahimzadeh, Seyed Ali Asghar Akbari Mousavi, Investigation on pulsed Nd:YAG laser welding of 49Ni-. Fe soft magnetic alloy, Materials and Design, 38 (2012), 115-123 https://doi.org/10.1016/j.matdes.2012.01.037
  9. M.H. Mahdieh, M. Nikbakht, Z. Eghlimi Moghadam, M. Sobhani, Crater geometry characterization of Al targets irradiated by single pulse and pulsen trains of Nd:YAG laser in ambient air and water, Applied Surface Science, 256 (2010), 1788-1783
  10. Yousuke Kawahito, Takeshi Terajima, Hisamich Kimura, Toshio Kuroda, Kazuhiro Nakata, Seiji Katayama, Akihisa Inoue, High-power fiber laser welding and its application to metallic glass Zr55Al10Ni5Cu30, Materials Science and Engineering B, 148 (2008), 105-109 https://doi.org/10.1016/j.mseb.2007.09.062
  11. J.D.Kim, J.S.Kim, S.W.Kim, C.K.Chun, S.J.Lee, I.D. Park and J.Seo, Crater Control by the Solidification Rate Adjustment in the Fiber Laser Welding of Pure Titanium, 2016 Spring Conference of the Korean Welding and Joining Society, 46 (2016) (in Korean)