설비공학논문집 (Korean Journal of Air-Conditioning and Refrigeration Engineering)

  • 제28권2호
  • /
  • Pages.63-68
  • /
  • 2016
  • /
  • 1229-6422(pISSN)
  • /
  • 2465-7611(eISSN)
대한설비공학회 (The Society of Air-Conditioning and Refrigerating Engineers of Korea)
권호 표지
DOI QR코드

DOI QR Code

창호 풍지판 형상에 따른 기밀성의 실험적 연구

An Experimental Study of Window Air Tightness according to Filling Piece Shapes

  • 윤유라 (서울과학기술대학교 주택대학원) ;
  • 박종준 (서울과학기술대학교 일반대학원 건축과) ;
  • 김영일 (서울과학기술대학교 건축학부) ;
  • 정광섭 (서울과학기술대학교 건축학부)
  • Yun, Yura (Department of Housing Environmental Service Engineering, Graduate School of Housing, Seoul National University of Science and Technology) ;
  • Park, Jong-Jun (Department of Architecture, Graduate School, Seoul National University of Science and Technology) ;
  • Kim, Young Il (School of Architecture, Seoul National University of Science and Technology) ;
  • Chung, Kwang-Seop (School of Architecture, Seoul National University of Science and Technology)
  • 투고 : 2015.11.25
  • 심사 : 2016.01.06
  • 발행 : 2016.02.10
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

To study the effect of installation and the shapes of filling pieces used for windows on the infiltration rate, infiltration tests were performed with two types of sliding windows and two shapes for the filling pieces. Infiltration occurred most at the top and bottom parts of the center location where two windows overlap, indicating the necessity of a filling piece to be installed at these locations. Infiltration velocity is proportional to the square root of the pressure difference, complying well with the theoretical correlation. Infiltration is reduced about 50% by the filling piece installation. This study shows that filling pieces are essential and their shapes play significant roles in reducing the infiltration of windows.

키워드

참고문헌

  1. Jang, C. Y. and Lee, N. E., 2010, A Measurement and Evaluation of Air Tightness of temperable Low-e Windows, Proceedings of SAREK, pp. 368-371.
  2. Kim, S. S., Cho, S., Yoon, Y., J., and Park, H. S., 2005, The Study on the Determining of the Infiltration Coefficient by Window Types, Journal of Architectural Institute of Korea of Planning and Design, Vol. 21, No. 4, pp. 183-189.
  3. Chung, J. M., 2012, A study on the Development of the Door Hardwares Construction Specification for Safety and Quality Improvement of Building Door, MS thesis, Seoul National University of Science and Technology.
  4. Moon, S. D., Chung, J. M., and Ock, J. H., 2013, Analysis of the Causes of Defects in Fenestration Construction and Their Impacts on Construction Quality, Journal of the Korea Institute of Building Construction, Vol. 13, No. 4, pp. 341-350. https://doi.org/10.5345/JKIBC.2013.13.4.341
  5. Jeong, H. G., 2008, A Study on the Effect of Window System on Indoor Temperature and Building Energy Consumption, MS thesis, Seoul National University of Science and Technology.
  6. Park, J. J., Kim, Y. I., and Chung, K. S., 2013, Study of Infiltration due to Window Air Permeability in Officetel, Proceedings of SAREK, pp. 742-745.
  7. Korea Standard Association, 2013, KS F 2292, The test method of air tightness for windows and doors.