DOI QR코드

DOI QR Code

오스테나이트계 FeMnAlC 경량철강의 용접열영향부 미세조직 변화 및 인장특성에 관한 연구

An Investigation on the Microstructure Evolution and Tensile Property in the Weld Heat-Affected Zone of Austenitic FeMnAlC Lightweight Steels

  • 문준오 (한국기계연구원 부설 재료연구소 철강재료연구실) ;
  • 박성준 (한국기계연구원 부설 재료연구소 철강재료연구실)
  • Moon, Joonoh (Ferrous Alloy Department, Advanced Metallic Materials Division, Korea Institute of Materials Science) ;
  • Park, Seong-Jun (Ferrous Alloy Department, Advanced Metallic Materials Division, Korea Institute of Materials Science)
  • 투고 : 2017.01.31
  • 심사 : 2017.02.17
  • 발행 : 2017.02.28

초록

IMicrostructure evolution and tensile property in the weld heat-affected zone (HAZ) of austenitic Fe-30Mn-9Al-0.9C lightweight steels were investigated. Five alloys with different V and Nb content were prepared by vacuum induction melting and hot rolling process. The HAZ samples were simulated by a Gleeble simulator with welding condition of 300kJ/cm heat input and HAZ peak temperatures of $1150^{\circ}C$ and $1250^{\circ}C$. Microstructures of base steels and HAZ samples were observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), and their mechanical properties were evaluated by tensile tests. The addition of V and Nb formed fine V and/or Nb-rich carbides, and these carbides increased tensile and yield strength of base steels by grain refinement and precipitation hardening. During thermal cycle for HAZ simulation, the grain growth occurred and the ordered carbide (${\kappa}-carbide$) formed in the HAZs. The yield strength of HAZ samples (HAZ 1) simulated in $1150^{\circ}C$ peak temperature was higher as compared to the base steel due to the formation of ${\kappa}-carbide$, while the yield strength of the HAZ samples (HAZ 2) simulated in $1250^{\circ}C$ decreased as compared to HAZ 1 due to the excessive grain growth.

키워드

참고문헌

  1. H. Kim, D.-W. Suh, and N.-J. Kim, Fe-Al-Mn-C lightweight structural alloys: a review on the microstructures and mechanical properties, Sci. Technol. Adv. Mater., 14 (2013), 1-11
  2. G. Frommeyer and U. Brux, Microstructures and mechanical properties of high-strength Fe-Mn-Al-C lightweight TRIPLEX steels, Steel Res. Int., 77 (2006), 627-633 https://doi.org/10.1002/srin.200606440
  3. J. Moon, S.-J. Park, J.H. Jang, T.-H. Lee, C.-H. Lee, H.-U. Hong, D.-W. Suh, S.H. Kim, H.N. Han and B.H. Lee, Atomistic investigations of ${\kappa}$-carbide precipitation in austenitic Fe-Mn-Al-C lightweight steels and the effect of Mo addition, Scripta Mater., 127 (2017) 97-101 https://doi.org/10.1016/j.scriptamat.2016.08.036
  4. J.D. Yoo, K.-T. Park, Microband-induced plasticity in a high Mn-Al-C light steel, Mater. Sci. & Eng. A 496 (2008), 417-424 https://doi.org/10.1016/j.msea.2008.05.042
  5. J. Moon and S.-J. Park, Microstructure and mechanical property in the weld heat-affected zone of V-added austenitic Fe-Mn-Al-C low density steels, J. of Welding and Joining, 33 (5) (2015), 31-34 https://doi.org/10.5781/JWJ.2015.33.5.31
  6. K. Easterling, Introduction to the physical metallurgy of welding (1st Edition), (1983), 23-24
  7. J. Moon and C. Lee, Microstructure evolution and its effect on strength during thermo-mechanical cycling in the weld coarse-grained heat-affected zone of Ti-Nb added HSLA steel, Journal of KWJS, 31 (6) (2013), 44-49 (in Korean)
  8. S.-H. Uhm, J.-O. Moon, H.-C. Jenog, J.-B. Lee and C. Lee, Prediction model for the microstructure and properties in weld heat affected zone: III. Prediction model for the austenite grain growth considering the influence of initial austenite grain size in weld HAZ of precipitates free low alloyed steel, Journal of KWS, 24 (4) (2006), 39-49 (in Korean)