DOI QR코드

DOI QR Code

Service ORiented Computing EnviRonment (SORCER) for deterministic global and stochastic aircraft design optimization: part 2

  • Raghunath, Chaitra (Department of Computer Science, Virginia Polytechnic Institute & State University) ;
  • Watson, Layne T. (Department of Computer Science, Virginia Polytechnic Institute & State University) ;
  • Jrad, Mohamed (Department of Aerospace & Ocean Engineering, Virginia Polytechnic Institute & State University) ;
  • Kapania, Rakesh K. (Department of Aerospace & Ocean Engineering, Virginia Polytechnic Institute & State University) ;
  • Kolonay, Raymond M. (AFRL/RQVC)
  • 투고 : 2016.05.18
  • 심사 : 2016.09.20
  • 발행 : 2017.05.25

초록

With rapid growth in the complexity of large scale engineering systems, the application of multidisciplinary analysis and design optimization (MDO) in the engineering design process has garnered much attention. MDO addresses the challenge of integrating several different disciplines into the design process. Primary challenges of MDO include computational expense and poor scalability. The introduction of a distributed, collaborative computational environment results in better utilization of available computational resources, reducing the time to solution, and enhancing scalability. SORCER, a Java-based network-centric computing platform, enables analyses and design studies in a distributed collaborative computing environment. Two different optimization algorithms widely used in multidisciplinary engineering design-VTDIRECT95 and QNSTOP-are implemented on a SORCER grid. VTDIRECT95, a Fortran 95 implementation of D. R. Jones' algorithm DIRECT, is a highly parallelizable derivative-free deterministic global optimization algorithm. QNSTOP is a parallel quasi-Newton algorithm for stochastic optimization problems. The purpose of integrating VTDIRECT95 and QNSTOP into the SORCER framework is to provide load balancing among computational resources, resulting in a dynamically scalable process. Further, the federated computing paradigm implemented by SORCER manages distributed services in real time, thereby significantly speeding up the design process. Part 1 covers SORCER and the algorithms, Part 2 presents results for aircraft panel design with curvilinear stiffeners.

키워드

과제정보

연구 과제 주관 기관 : Air Force Research Laboratory

참고문헌

  1. Amos, B.D., Easterling, D.R., Watson, L.T., Thacker, W.I., Castle, B.S. and Trosset, M.W. (2014b), "Algorithm XXX: QNSTOP: Quasi-Newton algorithm for stochastic optimization", Computer Science Technical Report 2014-07, Virginia Polytechnic Institute and State University, Blacksburg, VA.
  2. Bisagni, C. and Lanzi, L. (2002), "A post-buckling optimisation of composite stiffened panels using neural networks", Compos. Struct., 58(2), 237-247. https://doi.org/10.1016/S0263-8223(02)00053-3
  3. Boni, L., Fanteria, D. and Lanciotti, A. (2012), "A post-buckling behavior of flat stiffened composite panels: experiments vs. analysis", Compos. Struct., 94(12), 3421-3433. https://doi.org/10.1016/j.compstruct.2012.06.005
  4. Jrad, M. (2015), "Multidisciplinary optimization and damage tolerance of stiffened structures", Ph.D. Thesis, Department of Aerospace and Ocean Engineering, Virginia Polytechnic Institute & State University, Blacksburg, VA.
  5. Jrad, M., Khan, A.I. and Kapania, R.K. (2014), "Buckling Analysis of Curvilinearly Stiffened Composite Panels with Cracks", Proceedings of the AIAA 2014-0165, 55th Structures, Structural Dynamics, and Materials Conference (SDM), Maryland, National Harbor.
  6. Lanzi, L. and Giavotta, V. (2006), "A post-buckling optimization of composite stiffened panels: computations and experiments", Compos. Struct., 73(2), 208-220. https://doi.org/10.1016/j.compstruct.2005.11.047
  7. Liu, Q., Jrad, M., Mulani, S.B. and Kapania, R.K. (2015), "Integrated Global Wing and Local Panel Optimization of Aircraft Wing", Proceedings of the AIAA 2015-0137, 56th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, Kissimmee, Florida.
  8. Locatelli, D., Liu, Q., Tamijani, A.Y., Mulani, S.B. and Kapania, R.K. (2013), "Multidisciplinary optimization of supersonic wing structures using curvilinear Spars and Ribs (SpaRibs)", Proceedings of the AIAA 2013-1931, 54th AIAA/ASME/ASCE/AHS/ASC Structures Conference, Boston, Massachusetts.
  9. Montemurro, M., Vincenti, A. and Vannucci, P. (2012), "A two-level procedure for the global optimum design of composite modular structures-application to the design of an aircraft wing. Part 1: theoretical formulation", J. Optim. Theor. Appl., 155(1), 1-23. https://doi.org/10.1007/s10957-012-0067-9
  10. Montemurro, M., Vincenti, A. and Vannucci, P. (2012), "A two-level procedure for the global optimum design of composite modular structures-application to the design of an aircraft wing. Part 2: numerical aspects and examples", J. Optim. Theor. Appl., 155(1), 24-53. https://doi.org/10.1007/s10957-012-0070-1
  11. Mulani, S.B., Locatelli, D. and Kapania, R.K. (2010), "Algorithm development for optimization of arbitrary geometry panels using curvilinear stiffeners", Proceedings of the AIAA 2010-2674, 51st AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, Orlando, Florida.
  12. Mulani, S.B., Slemp, W.C.H. and Kapania, R.K. (2013), "EBF3PanelOpt: an optimization framework for curvilinear blade-stiffened panels", Thin Wall. Struct., 63, 13-26. https://doi.org/10.1016/j.tws.2012.09.008
  13. Raghunath, C. (2015), Service Oriented Computing Environment (SORCER) for Deterministic Global and Stochastic Optimization, M.S. thesis, Department of Computer Science, Virginia Polytechnic Institute & State University, Blacksburg, VA.
  14. Taminger, K.M.B. and Hafley, R.A. (2003), "Electron beam freeform fabrication: a rapid metal deposition process", Proceedings of the Third Annual Automotive Composites Conference, Troy, Michigan.