DOI QR코드

DOI QR Code

Physical Properties of Cement System Insulation Using Blast Furnace Slag

  • Seo, Sung Kwan (Energy and Environmental Division, Korea Institute of Ceramic Engineering and Technology) ;
  • Park, Jae Wan (Energy and Environmental Division, Korea Institute of Ceramic Engineering and Technology) ;
  • Cho, Hyeong Kyu (Energy and Environmental Division, Korea Institute of Ceramic Engineering and Technology) ;
  • Chu, Yong Sik (Energy and Environmental Division, Korea Institute of Ceramic Engineering and Technology)
  • Received : 2017.11.01
  • Accepted : 2017.12.11
  • Published : 2018.01.31

Abstract

In this study, fabrication method of inorganic insulation were studied to reduce $CO_2$ from buildings. Main materials for inorganic insulation were used cement, blast furnace slag and aluminum powder as foaming agent. Mixing ratio of cement and slag was controlled and physical properties of inorganic insulation were analyzed. When inorganic insulation was fabricated using cement and slag, expanded slurries were not sunken and hardened normally. Pore size was 0.5 - 2 mm; mean pore size was about 1mm in inorganic insulation. Compressive strength of inorganic insulation increased with curing time and increased slightly with cement fineness. However, specific gravity decreased slightly with curing time; this phenomenon was caused by evaporation of adsorptive water. When inorganic insulation was dried at $60^{\circ}C$, compressive strength was higher than that of undried insulation. The highest compressive strength was found with a mixture of cement (50%) and slag (30%) in inorganic insulation. Compressive strength was 0.32 MPa, thermal conductivity was 0.043 W/mK and specific gravity was $0.12g/cm^3$.

Keywords

References

  1. Y. S. Song, W. Y. Jeong, and T. H. Kim, "An Examination of Application Plan of Proper CDM for GHG Reduction," J. Reg. Assoc. Archit. Inst. Korea, 12 [4] 82-177 (2010).
  2. Y. S. Jeong and H. K. Jung, "A Study on Calculation Method for the Gas Emission of Building Sector," J. Reg. Assoc. Archit. Inst. Korea, 37 [1] 499-500 (2017).
  3. S. K. Jeong, J. S. Jeon, and J. K. Seo, "Consideration for application of Phase Change Material for Building Energy Saving," J. KIAEBS, 5 [1] 1-9 (2011).
  4. K. H. Lee and C. W. Chae, "A Study on the Amount of the Energy Consumption and $CO_2$ Emission of Public Building using the Input-Output Analysis," Architectural Institute of Korea, 18 [5] 99-107 (2002).
  5. J. H. Park and T. H. Hoon, "Improvements of Policies Related Building Energy Reduction in Korea," Korea Inst. Construct. Eng. Manage., 11 [4] 14-21 (2010). https://doi.org/10.6106/KJCEM.2010.11.6.14
  6. J. M. Park, D. H. Kim, and D. J. Suh, "Recent Research Trends for Green Building Thermal Insulation Materials," Clean Technol., 18 [1] 14-21 (2012). https://doi.org/10.7464/ksct.2012.18.1.014
  7. D. K. Kim and S. B. Lee, "Properties and Thermal Characteristics of Phenol Foam for Heat Insulating Materials," J. Ind. Eng. Chem., 17 [4] 357- 60 (2006).
  8. J. S. Roh, J. Y. Yoon, K. J. Moon, Y. K. Cho, and Y. S. So, "Heating Value and Noxious Gases Generation of Sandwich Panel Core Using Artificial Lightweight Aggregate"; pp. 261-66 in Proceedings of Korea Concrete Institute, 2003.
  9. J. S. Kim, "Efficient Application of Insulation for Green Plant," Korean J. Chem. Eng., 29 [1] 79-84 (2011).
  10. M. S. Ahn, T. K. Park, I. S. Hwang, and B. I. Kim, "Effect of Gypsum and Cement on Hydrothermal Reaction in Fly Ash-Lime System," J. Korean Ceram. Soc., 35 [10] 1030-39 (1998).
  11. J. K. Park and J. S. Lee, "Preparation of Porous Inorganic Materials by Foaming Slurry," J. Korean Ceram. Soc., 35 [1] 1280-85 (1998).
  12. W. K. Jung, K. H. Kim, B. J. Jeon, and J. O. Bae, "Development of Carbon Reduction Concrete Using The Pozzolan Reaction Cement"; pp. 77-8 in Proceedings of Korea Concrete Institute, 2013.

Cited by

  1. Chemical design of lightweight aggregate to prevent adhesion at bloating activation temperature vol.8, pp.2, 2020, https://doi.org/10.1080/21870764.2020.1725259