Transactions of Materials Processing (소성∙가공)

The Korean Society for Technology of Plasticity and materials processing (한국소성∙가공학회)
권호 표지
DOI QR코드

DOI QR Code

Study of Frictional Behavior of AZ31B Mg Alloy at Elevated Temperature

AZ31B 마그네슘 합금의 온간 마찰 특성 연구

  • Han, S.S. (Department of Mechanical Engineering, Kumoh National Institute of Technology)
  • 한수식 (금오공과대학교 기계공학과)
  • Received : 2018.01.29
  • Accepted : 2018.03.28
  • Published : 2018.06.01
Download PDF
⟨ Previous Next ⟩

Abstract

The success of warm forming of Mg alloy sheets is very dependent on its frictional behavior at elevated temperatures. The effects of contact pressure and sliding length on the frictional characteristics of AZ31B Mg alloy sheet were investigated at elevated temperature and at room temperature. The contact pressure range for the friction test was determined through FE analysis of the roof panel which is a candidate for Mg alloy application. According to the experimental results, the frictional behavior of the Mg alloy sheet is equally highly influenced by both sliding length and contact pressure at room temperature. At elevated temperatures, however, the sliding length has a more dominant influence on the frictional characteristics of the Mg alloy sheet than the contact pressure, if the contact pressure is lower than a certain level.

Keywords

References

  1. D. H. Park, Y. H. Tak, S. H. Um, J. J. Yun, C. W. Lee, 2013, Car Body Forming Technology using Magnesium Alloy Sheet, Proc. Kor. Soc. Tech. Plast. Conf., pp.239-240.
  2. G. H. Lee, T. W. Yoon, C. Y. Kang, 2014, A Study on the Mechanical Properties and Formability of Mg AZ31B Sheet, Trans. Mater. Process., 23(8), pp.495-500. https://doi.org/10.5228/KSTP.2014.23.8.495
  3. S. H. Kim, K. D. Park, J. H. Jang, K. T. Kim, H. W. Lee, G. A. Lee, K. P. Kim, Y. S. Lee, 2008, Experimental and Analytical Researches on Mechanical Properties Related to Formability of AZ31B Alloy Sheet, Trans. Mater. Process., 17(7), pp.466-472. https://doi.org/10.5228/KSPP.2008.17.7.466
  4. H. Y. Kim, S. C. Choi, H. S. Lee, H. J. Kim, K. T. Lee, 2007, Experiments for Forming Limit Diagram and Springback Characteristics of AZ31B Magnesium Alloy Sheet at Elevated Temperature, Trans. Mater. Process., 16(5), pp.364-369. https://doi.org/10.5228/KSPP.2007.16.5.364
  5. Y. S. Lee, Y. N. Kwon, S. H. Kang, S. W. Kim, J. H. Lee, 2008, Forming Limit of AZ31 Alloy Sheet and Strain Rate on Warm Sheet Metal Forming, J. Mater. Process. Technol., Vol. 201, No. 1, pp. 431-435. https://doi.org/10.1016/j.jmatprotec.2007.11.306
  6. H. W. Kwon, N. Yoon, J. C. Kim, Y.-J. Jeong, Y.-S. Kim, 2011, Tribological Characteristics during Sheet Forming of the AZ31B Mg alloy, Proc. Kor. Soc. Tech. Plast. Conf., 10, pp.88-91.
  7. H. Gwon, M. G. Kim, H. L. Hur, Y.-S. Kim, 2014, Correlation between galling and friction coefficient measured during sheet forming of Mg alloy using a steel die, Proc. Kor. Soc. Tech. Plast. Conf., 10, pp.174-177.