DOI QR코드

DOI QR Code

Parametric studies on punching shear behavior of RC flat slabs without shear reinforcement

  • Elsamak, Galal (Department of Civil Engineering, Faculty of Engineering, Kafrelsheikh University) ;
  • Fayed, Sabry (Department of Civil Engineering, Faculty of Engineering, Kafrelsheikh University)
  • 투고 : 2019.06.12
  • 심사 : 2020.03.30
  • 발행 : 2020.04.25

초록

This paper proposed a numerical investigation based on finite elements analysis (FEA) in order to study the punching shear behavior of reinforced concrete (RC) flat slabs using ABAQUS and SAP2000 programs. Firstly, the concrete and the steel reinforcements were modeled by hexahedral 3D solid and linear elements respectively, and the nonlinearity of the used materials was considered. In order to validate this model, experimental results considered in literature were compared with the proposed FE model. After validation, a parametric study was performed. The parameters include the slab thickness, the flexure reinforcement ratios and the axial membrane loads. Then, to reduce the time of FEA, a simplified modelling using 3D layered shell element and shear hinge concept was also induced. The effect of the footings settlement was studied using the proposed simplified nonlinear model as a case study. Results of numerical models showed that increase of the slab thickness by 185.7% enhanced the ultimate load by 439.1%, accompanied with a brittle punching failure. The punching failure occurred in one of the tested specimens when the tensile reinforcement ratio increased more than 0.65% and the punching capacity improved with increasing the horizontal flexural reinforcement; it decreased by 30% with the settlement of the outer footings.

키워드

참고문헌

  1. Abaqus Theory Manual (6.14) (2014), Dassault Systemes, Providence, RI, USA.
  2. ACI Committee & International Organization for Standardization (2008), Building Code Requirements for Structural Concrete (ACI 318-08) and Commentary, American Concrete Institute.
  3. Ahsan, R. and Zahura, F.T. (2017), "Numerical study on effect of integrity reinforcement on punching shear of flat plate", Comput. Concrete, 20(6), 731-738. https://doi.org/10.12989/cac.2017.20.6.731.
  4. Alam, A.J., Amanat, K.M. and Seraj, S.M. (2009), "An experimental study on punching shear behavior of concrete slabs", Adv. Struct. Eng., 12(2), 257-265. https://doi.org/10.1260/136943309788251650.
  5. American Concrete Institute. (2014), Building Code Requirements for Structural Concrete (ACI 318-14), Commentary on Building Code Requirements for Structural Concrete (ACI 318R-14), An ACI Report, American Concrete Institute, ACI.
  6. Anna Polak, M. (2005), "Shell finite element analysis of RC plates supported on columns for punching shear and flexure", Eng. Comput., 22(4), 409-428. https://doi.org/10.1108/02644400510598750.
  7. Belletti, B., Walraven, J.C. and Trapani, F. (2015), "Evaluation of compressive membrane action effects on punching shear resistance of reinforced concrete slabs", Eng. Struct., 95, 25-39. https://doi.org/10.1016/j.engstruct.2015.03.043.
  8. Birkle, G. and Dilger, W.H. (2008), "Influence of slab thickness on punching shear strength", ACI Struct. J., 105(2), 180.
  9. Einpaul, J., Bujnak, J., Fernandez Ruiz, M. and Muttoni, A. (2016), "Study on influence of column size and slab slenderness on punching strength", ACI Struct. J., 113, 135-145.
  10. Eurocode 2; BS EN 1992-1-1 (2004), Design of Concrete Structures, General Rules and Rules for Buildings, Section 3.1.5.
  11. Federal Emergency Management Agency (2000), Pre-Standard and Commentary for Seismic Rehabilitation of Buildings, Report No. FEMA-356, Washington DC.
  12. Genikomsou, A.S. and Polak, M.A. (2014), "Finite element analysis of a reinforced concrete slab-column connection using ABAQUS", Structure Congress ASCE, 813, 823. https://doi.org/10.1061/9780784413357.072.
  13. Guan, H. (2009), "Prediction of punching shear failure behaviour of slab-edge column connections with varying opening and column parameters", Adv. Struct. Eng., 12(1), 19-36. https://doi.org/10.1260/136943309787522605.
  14. Guandalini, S., Burdet, O. and Muttoni, A. (2009), "Punching tests of slabs with low reinforcement ratios", ACI Struct., 106(1), 87-95
  15. Lips, S., Fernandez Ruiz, M. and Muttoni, A. (2012), "Experimental investigation on punching strength and deformation capacity of shear-reinforced slabs", ACI Struct. J., 109, 889-900.
  16. Mander, J.B., Priestley, M.J. and Park, R. (1988), "Theoretical stress-strain model for confined concrete", J. Struct. Eng., 114(8), 1804-1826. https://doi.org/10.1061/(ASCE)0733-9445(1988)114:8(1804).
  17. Meisami, M.H., Mostofinejad, D. and Nakamura, H. (2013), "Punching shear strengthening of two-way flat slabs using CFRP rods", Compos. Struct., 99, 112-122. https://doi.org/10.1016/j.compstruct.2012.11.028.
  18. Sagaseta, J., Muttoni, A., Fernandez Ruiz, M. and Tassinari, L. (2011), "Non-axis-symmetrical punching shear around internal columns of RC slabs without transverse reinforcement", Mag. Concrete Res., 63(6), 441-457. https://doi.org/10.1680/macr.10.00098.
  19. Saleh, H., Kalfat, R., Abdouka, K. and Al-Mahaidi, R. (2018), "Experimental and numerical study into the punching shear strengthening of RC flat slabs using post-installed steel bolts", Constr. Build. Mater., 188, 28-39. https://doi.org/10.1016/j.conbuildmat.2018.08.064.
  20. SAP 2000. Version 20 (2017), CSI-Computers and Structures Inc., 2000.
  21. Schmidt, P., Kueres, D. and Hegger, J. (2019), "Punching shear behavior of reinforced concrete flat slabs with a varying amount of shear reinforcement", Struct. Concrete, 21(1), 235-246. https://doi.org/10.1002/suco.201900017.
  22. Shu, J., Plos, M., Zandi, K., Johansson, M. and Nilenius, F. (2016), "Prediction of punching behaviour of RC slabs using continuum non-linear FE analysis", Eng. Struct., 125, 15-25. https://doi.org/10.1016/j.engstruct.2016.06.044.

피인용 문헌

  1. Experimental study of punching shear in post-tensioned slabs with unbonded tendons vol.79, pp.4, 2020, https://doi.org/10.12989/sem.2021.79.4.507