DOI QR코드

DOI QR Code

A simple panel zone model for linear analysis of steel moment frames

  • Saffari, Hamed (Department of Civil Engineering, Faculty of Engineering, Shahid Bahonar University of Kerman) ;
  • Morshedi, Esmaeil (Department of Civil Engineering, Faculty of Engineering, Shahid Bahonar University of Kerman)
  • 투고 : 2019.11.15
  • 심사 : 2020.04.30
  • 발행 : 2020.05.25

초록

Consideration of the panel zone (PZ) deformations in the analysis of steel moment frames (SMFs) has a substantial effect on structural response. One way to include the PZ effect on the structural response is Krawinkler's PZ model, which is one of the best and conventional models. However, modeling of Krawinkler's PZ model has its complexity, and finding an alternative procedure for PZ modeling is of interest. In this study, an efficient model is proposed to simplify Krawinkler's PZ model into an Adjusted Rigid-End Zone (AREZ). In this way, the rigid-end-zone dimensions of the beam and column elements are defined through an appropriate rigid-end-zone factor. The dimensions of this region depend on the PZ stiffness, beam(s) and columns' specifications, and connection joint configuration. Thus, to obtain a relationship for the AREZ model, which yields the dimensions of the rigid-end zone, the story drift of an SMF with Krawinkler's PZ model is equalized with the story drift of the same structure with the AREZ model. Then, the degree of accuracy of the resulting relationship is examined in several connections of generic SMFs. Also, in order to demonstrate the applicability of the proposed model in SMFs, several SMFs ranging from 3- to 30-story representing low- to high-rise buildings are examined through linear static and dynamic time history analysis. Furthermore, non-linear dynamic analyses of three SMFs conducted to validate the degree of accuracy of the proposed model in the non-linear analysis of SMFs. Analytical results show that there is considerable conformity between inter-story drift ratio (IDR) results of the SMFs with Krawinkler's PZ model and those of the centerline SMFs with AREZ.

키워드

참고문헌

  1. AISC (1990), Load and resistance factor design specification for structural steel buildings, American Institute of Steel Construction; Chicago, USA.
  2. Anderson, J.C. and Bertero, V.V. (1997), "Implications of the landers and big bear earthquakes on earthquake resistant design of structures", UCB/EERC-97/08; Earthquake Engineering Research Center, University of California, Berkeley, USA.
  3. Adan, S.M. and Reaveley, R.D. (2006), "RBS moment connections without continuity plates", Proceedings of the 8th U.S. National Conference on Earthquake Engineering, San Francisco, USA, April.
  4. Bertero, V.V., Krawinkler, H. and Popov, E.P. (1973), "Further studies on seismic behavior of steel beam-to-column subassemblages", UBC/EERC-73/27; Earthquake Engineering Research Center, University of California, Berkeley, USA.
  5. Bayat, M. and Zahrai, S.M. (2017), "Seismic performance of mid-rise steel frames with semi-rigid connections having different moment capacity", Steel Compos. Struct., 25(1), 1-17. https://doi.org/10.12989/scs.2017.25.1.001.
  6. Charney, F.A. and Downs, W.M. (2004), "Modeling procedures for panel zone deformations in moment resisting frames", Proceedings of National Conference on Connections in Steel Structures V: Innovative Steel Connections, Amsterdam, the Netherlands, June.
  7. Castro, J.M., Elghazouli, A.Y. and Izzuddin, B.A. (2005), "Modelling of the panel zone in steel and composite moment frames", Eng. Struct., 27(1), 129-144. https://doi.org/10.1016/j.engstruct.2004.09.008.
  8. Downs, W.M. (2002), "Modeling and Behavior of the Beam/Column Joint Region of Steel Moment Resisting Frames", Ph.D. Dissertation, Virginia Tech, Virginia, USA.
  9. Elkady, A. and Lignos, D.G. (2015), "Effect of gravity framing on the overstrength and collapse capacity of steel frame buildings with perimeter special moment frames", Earthq. Eng. Struct. D., 44(8), 1289-1307. https://doi.org/10.1002/eqe.2519.
  10. Nunez, E., Torres, R. and Herrera, R. (2017), "Seismic performance of moment connections in steel moment frames with HSS columns", Steel Compos. Struct., 25(3), 271-286. https://doi.org/10.12989/scs.2017.25.3.271
  11. Fielding, D.J. and Huang, J.S. (1971), "Shear in steel beam-to-column connections", Welding J., 50(7), 313-326.
  12. FEMA (2000), "State of the Art Report on Systems Performance of Steel Moment Frames Subject to Earthquake Ground Shaking", FEMA-355C; SAC Joint Venture, Federal Emergency Management Agency, USA.
  13. Gupta, A. and Krawinkler, H. (1999), "Seismic demands for performance evaluation of steel moment resisting frame structures", TR 132; John A. Blume Earthquake Engineering Research Center, Stanford University, USA.
  14. Hamburger, R.O., Krawinkler, H., Malley J.O. and Adan S.M. (2009), "Seismic design of steel special moment frames: a guide for practicing engineers', NEHRP Seismic Design Technical Brief No. 2, USA.
  15. Krawinkler, H., Bertero, V.V. and Popov, E.P. (1971), "Inelastic behavior of steel beam-to-column subassemblages", EERC 71-7; Earthquake Engineering Research Center, University of California, Berkeley, USA.
  16. Krawinkler, H., Popov, E.P. and Bertero, V.V. (1975), "Shear behavior of steel frame joints", J. Struct. Division, 101(11), 2317-2336. https://doi.org/10.1061/JSDEAG.0004206
  17. Kawano, A. (1984), "Inelastic behavior of low-rise frame based on a weak beam-to-column connection philosophy to earthquake motion", Proceedings of the 8th World Conference on Earthquake Engineering, New Jersey, July
  18. Krawinkler, H. and Mohasseb, S. (1987), "Effects of panel zone deformations on seismic response", J. Constr. Steel Res., 8, 233-250. https://doi.org/10.1016/0143-974X(87)90060-5.
  19. Kim, K. and Engelhardt, M.D. (1995), "Development of analytical models for earthquake analysis of steel moment frames", Ph.D. Dissertation, Phil M. Ferguson Structural Engineering Laboratory, University of Texas at Austin, Texas, USA
  20. Kim, K. and Engelhardt, M.D. (2002), "Monotonic and cyclic loading models for panel zones in steel moment frames", J. Constr. Steel Res., 58(5), 605-635. https://doi.org/10.1016/S0143-974X(01)00079-7.
  21. Kalkan, E. and Kunnath, S.K. (2006a), "Effects of fling step and forward directivity on seismic response of buildings", Earthq. Spectra, 22(2), 367-390. https://doi.org/10.1193/1.2192560.
  22. Kalkan, E. and Kunnath, S.K. (2006b), "Adaptive modal combination procedure for nonlinear static analysis of building structures", J. Struct. Eng., 132(11), 1721-1731. https://doi.org/10.1061/(ASCE)0733-9445(2006)132:11(1721).
  23. Kalkan, E. and Chopra, A.K. (2010), "Practical guidelines to select and scale earthquake records for nonlinear response history analysis of structures", 1068(2010); U.S. Geological Survey, USA
  24. Lee, S.J., (1987), "Seismic Behavior of Steel Building structure with Composite Slabs", Ph.D. Thesis, Department of Civil Engineering, Lehigh University, Bethlehem, USA
  25. Lignos, D.G., and Krawinkler, H. (2009), "Sidesway collapse of deteriorating structural systems under seismic excitations", TB 172, The John A. Blume Earthquake Engineering Research Center, Stanford University, USA.
  26. Lignos, D.G. and Krawinkler, H. (2011), "Deterioration modeling of steel components in support of collapse prediction of steel moment frames under earthquake loading", J. Struct. Eng., 137(11), 1291-1302. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000376.
  27. Lu, L.F., Xu, Y.L., Zheng, H. and Lim, J.B. (2018a), "Cyclic response and design procedure of a weak-axis cover-plate moment connection", Steel Compos. Struct., 26(3), 329-345. https://doi.org/10.12989/scs.2018.26.3.329.
  28. Lu, L.F., Xu, Y.L. and Lim, J.B. (2018b), "Mechanical performance of a new I-section weak-axis column bending connection", Steel Compos. Struct., 26(1), 31-44. https://doi.org/10.12989/scs.2018.26.1.031.
  29. Lu, L.F., Xu, Y.L., Liu, J. and Lim, J.B. (2017), "Cyclic performance and design recommendations of a novel weak-axis reduced beam section connection", Steel Compos. Struct., 27(3), 337-353. https://doi.org/10.12989/scs.2017.27.3.337.
  30. Liew, J.R. and Chen, W.F. (1995), "Analysis and design of steel frames considering panel joint deformations", J. Struct.. Eng., 121(10), 1531-1540. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:10(1531).
  31. Mckenna, F.T. (1997), "Object-oriented finite element programming: frameworks for analysis, algorithms and parallel computing", Ph.D. Dissertation, University of California, Berkeley, USA
  32. Mansouri, I. and Saffari, H. (2014), "A new steel panel zone model including axial force for thin to thick column flanges", Steel Compos. Struct., 16(4), 417-436. https://doi.org/10.12989/scs.2014.16.4.417.
  33. Mansouri, I. and Saffari, H. (2015), "New mathematical modeling of steel panel zone with thin to thick column flanges", Asian J. Civil Eng. (BHRC), 16(4), 451-466.
  34. Popov, E.P. and Stephen, R.M. (1970), "Cyclic loading of full-size steel connections, UCB/EERC-70/03; Earthquake Engineering Research Center, University of California, Berkeley, USA.
  35. Popov E.P., Amin, N., Louie. J. and Stephen, R. (1985), "Cyclic behavior of large beam-column assembles", Earthq. Spectra, 1(2), 203-238. https://doi.org/10.1193/1.1585263
  36. Popov, E.P. (1987), "Panel zone flexibility in seismic moment joints", J. Constr. Steel Res., 8, 91-118. https://doi.org/10.1016/0143-974X(87)90055-1
  37. Poursha, M., Khoshnoudian, F. and Moghadam, A. (2010), "Assessment of modal pushover analysis and conventional nonlinear static procedure with load distributions of federal emergency management agency for high-rise buildings", Struct. Des. Tall Spec. Build., 19(3), 291-308. https://doi.org/10.1002/tal.487.
  38. Rafezy, B., Huynh, Q. and Gallart, H. (2014), "Explicit evaluation of steel panel zone stiffness using equivalent end zone (EEZ) model", SEAOC Convention, California, USA
  39. Slutter, R.G. (1982), "Tests of Panel Zone Behavior in Beam-column-connections," 200.81.403.1; Fritz Engineering Laboratory, Lehigh University, Bethlehem, Pennsylvania, USA
  40. Somerville, P.G. (1997), "Development of ground motion time histories for phase 2 of the FEMA/SAC steel project", SAC/BD-97/04; Structural Engineers Association of California, Applied Technology Council, California Universities for Research in Earthquake Engineering.
  41. Saffari, H., Sarfarazi, S. and Fakhraddini, A. (2016), "A mathematical steel panel zone model for flanged cruciform columns", Steel Compos. Struct., 20(4), 851-867. https://doi.org/10.12989/scs.2016.20.4.851
  42. Schneider, S.P. and Amidi, A. (1998), "Seismic behavior of steel frames with deformable panel zones", J. Struct. Eng., 124(1), 35-42. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:1(35)
  43. Tsai, K.C. and Popov, E.P. (1990), "Seismic panel zone design effect on elastic story drift in steel frames", J. Struct. Eng., 116(12), 3285-3301. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:12(3285).
  44. UBC 73 (1973), International conference of building officials, Uniform building code, Whittier, California, USA.
  45. UBC 94 (1994), International conference of building officials, Uniform building code, Whittier, California, USA.
  46. UBC 98 (1998), International conference of building officials, Uniform building code, Whittier, California, USA.
  47. Wang, S.J. (1989), "Seismic response of steel building frames with inelastic joint deformation," Ph.D. Dissertation, Lehigh University, Bethlehem, Pennsylvania, USA.
  48. 2800 Standard (2005), Iranian Code of Practice for Seismic Resistant Design of Buildings, Iran.