DOI QR코드

DOI QR Code

Experimental and numerical studies on the behaviour of corroded cold-formed steel columns

  • Nie, Biao (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Xu, Shanhua (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Zhang, Haijiang (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Zhang, Zongxing (School of Civil Engineering, Xi'an University of Architecture & Technology)
  • 투고 : 2020.01.15
  • 심사 : 2020.05.13
  • 발행 : 2020.06.10

초록

Experimental investigation and finite element analysis of corroded cold-formed steel (CFS) columns are presented. 11 tensile coupon specimens and 6 stub columns of corroded CFS that had a channel section of C160x60x20 were subjected to monotonic tensile tests and axial compression tests, respectively. The degradation laws of the mechanical properties of the tensile coupon specimens and stub columns were analysed. An appropriate finite element model for the corroded CFS columns was proposed and the influence of local corrosion on the stability performance of the columns was studied by finite element analysis. Finally, the axial capacity of the experimental results was compared with the predictions obtained from the existing design specifications. The results indicated that with an increasing average thickness loss ratio, the ultimate strength, elastic modulus and yield strength decreased for the tensile coupon specimens. Local buckling deformation was not noticeable until the load reached about 90% of the ultimate load for the non-corroded columns, while local buckling deformation was observed when the load was only 40% of the ultimate load for the corroded columns. The maximum reduction of the ultimate load and critical buckling load was 57% and 81.7%, respectively, compared to those values for the non-corroded columns. The ultimate load of the columns with web thickness reduced by 2 mm was 53% lower than that of the non-corroded columns, which indicates that web corrosion most significantly affects the bearing capacity of the columns with localized corrosion. The results predicted using the design specifications of MOHURD were more accurate than those predicted using the design specifications of AISI.

키워드

과제정보

This work was supported by 13th Five-Year national focus on R & D project of China with Grant No. 2016YFC0701305 and the National Nature Foundation of China with Grant No.51678477.

참고문헌

  1. AISI S100-16 (2016), North American Specifcation for the Design of Cold-Formed Steel Structural Members, American Iron and Steel Institute, USA.
  2. Ananthi, G., Roy, K., Chen, B. and Lim, J.B.P. (2019), "Testing, simulation and design of back-to-back built-up cold-formed steel unequal angle sections under axial compression", Steel. Compos. Struct., 33(4), 595-614. https://doi.org/10.12989/scs.2019.33.4.595.
  3. Beaulieu, L.V., Legeron, F. and Langlois S. (2010), "Compression strength of corroded steel angle members", J. Struct. Steel Res., 66(11), 1366-1373. https://doi.org/10.1016/j.jcsr.2010.05.006.
  4. Chen, B., Roy, K., Uzzaman, A., Raftery, G.M., Nash, D., Clifton, G.C. and Lim, J.B. (2019), "Effects of edge-stiffened web openings on the behaviour of cold-formed steel channel sections under compression", Thin-Wall. Struct., 144, 106307. https://10.1016/j.tws.2019.106307.
  5. Cinitha, A., Umesha, P.K. and Iyer, N.R. (2014), "An overview of corrosion and experimental studies on corroded mild steel compression members", KSCE J. Civ. Eng. Archit., 18(6), 1735-1744. https://doi.org/10.1007/s12205-014-0362-0.
  6. Cinitha, A., Umesha, P.K., Palani, G.S. and Sampath, V. (2018), "Compression behaviour of ssteel tubular members under simulated corrosion and elevated temperature", Int. J. Steel Struct., 18(1), 139-152. https://doi.org/10.1007/s13296-018-0311-8.
  7. Dunbar, T.E., Pegg, N., Taheri, F. and Jiang, L. (2004), "A computational investigation of the effects of localized corrosion on plates and stiffened panels", Mar. Struct., 17, 385-402. https://doi.org/10.1016/j.marstruc.2004.08.012.
  8. Garbatov, Y., Soares, C.G., Parunov, J. and Kodvanj, J. (2014), "Tensile strength assessment of corroded small scale specimens", Corros. Sci., 85, 296-303. https://doi.org/10.1016/j.corsci.2014.04.031.
  9. Karagah, H., Shi, C., Dawood, M., and Belarbi A. (2015), "Experimental investigation of short steel columns with localized corrosion", Thin-Wall. Struct., 87, 191-199. https://doi.org/10.1016/j.tws.2014.11.009.
  10. Khurram, N., Sasaki, E., Katsuchi, H. and Yamada, H. (2014), "Experimental and numerical evaluation of bearing capacity of steel plate girder affected by end panel corrosion", Int. J. Steel Struct., 14(3), 659-676. http://dx.doi.org/10.1007/s13296-015-3018-0.
  11. Kim, I.T., Lee, M.J., Ah, J.H. and Kainuma, S. (2013), "Experimental evaluation of shear buckling behaviors and strength of locally corroded web", J. Struct. Steel Res., 83, 75-89. https://doi.org/10.1016/j.jcsr.2012.12.015.
  12. Li, J., Li, M. and Sun, Z. (1999), "Development of an artificial climatic complex accelerated corrosion tester and investigation of complex accelerated corrosion test methods", Corrosion, 55 (5), 498-502. https://doi.org/10.5006/1.3284012.
  13. Melchers, R.E. and Wells, T. (2006), "Models for the anaerobic phases of marine immersion corrosion", Corros. Sci., 48, 1791-1811. https://doi.org/10.1016/j.corsci.2005.05.039.
  14. Nakai, T., Matsushita, H., Yamamoto, N. and Arai, H. (2004), "Effect of pitting corrosion on local strength of hold frames of bulk carriers (1st report)", Mar. Struct., 17, 403-432. https://doi.org/10.1016/j.marstruc.2004.10.001.
  15. Nakhaie, D. and Moayed, M.H. (2014), "Pitting corrosion of cold rolled solution treated 17-4 PH stainless steel", Corros. Sci., 80, 290-298. https://doi.org/10.1016/S0010-938X(78)80086-9.
  16. Nie, B., Xu, S., Yu, J. and Zhang, H.J. (2019), "Experimental investigation of mechanical properties of corroded cold-formed steels", J. Struct. Steel Res., 162, 105706. https://doi.org/10.1016/j.jcsr.2019.105706.
  17. Ok, D., Pu, Y. and Incecik, A. (2007), "Computation of ultimate strength of locally corroded unstiffened plates under uniaxial compression", Mar. Struct., 20, 100-114. https://doi.org/10.1016/j.marstruc.2007.02.003.
  18. Paik, J.K., Lee, J.M. and Ko, M.J. (2003), "Ultimate strength of plate elements with pit corrosion wastage", J. Eng. Marit. Environ., 217, 185-200. https://doi.org/10.1177/147509020321700402.
  19. Qin, G., Xu, S., Yao, D. and Zhang, Z. (2016), "Study on the degradation of mechanical properties of corroded steel plates based on surface topography", J. Struct. Steel Res., 125, 205-217. https://doi.org/10.1016/j.jcsr.2016.06.018.
  20. Qiu, B. and Xu, S. (2014), "Degradation law of mechanical properties of corroded steel plates", Mech. Eng. Mater., 38, 60-63. https://doi.org/1000-3738(2014)10-0060-04
  21. Rahgozar, R. (2009), "Remaining capacity assessment of corrosion damaged beams using minimum curves", J. Struct. Steel Res., 65(2), 299-307. https://doi.org/10.1016/j.jcsr.2008.02.004.
  22. Roy, K., Lau, H.H. and Lim, J.B.P. (2019a), "Finite element modelling of back-to-back built-up cold-formed stainless-steel lipped channels under axial compression", Steel. Compos. Struct., 33(1), 869-898. https://doi.org/10.12989/scs.2019.33.1.869.
  23. Roy, K., Ting, T.C., Lau, H.H. and Lim, J.B. (2019b), "Experimental and numerical investigations on the axial capacity of cold-formed steel built-up box sections", J. Struct. Steel Res., (160), 411-427.
  24. Roy, K., Ting, T., Lau, H.H. and Lim, J.B. (2018), "Nonlinear behavior of axially loaded back-to-back built-up cold-formed steel un-lipped channel sections", Steel. Compos. Struct., 28(2), 233-250. https://doi.org/10.12989/scs.2018.28.2.233.
  25. Saad-Eldee, S., Garbatov, Y. and Soares, C.G. (2012), "Effect of corrosion degradation on ultimate strength of steel box girders", Corros. Eng. Sci. Technol., 47(4), 272-283. https://doi.org/10.1179/1743278212Y.0000000005.
  26. Sharifi, Y. and Rahgozar, R. (2010), "Remaining moment capacity of corroded steel beams", Int. J. Steel Struct., 10(2), 165-176. http://dx.doi.org/10.1007/BF03215828.
  27. Sheng, J. and Xia, J. (2017), "Effect of simulated pitting corrosion on the tensile properties of steel", Constr. Build. Mater., 131, 90-100. https://doi.org/10.1016/j.conbuildmat.2016.11.037.
  28. Shi, C., Karagah, H., Dawood, M. and Belarbi, A. (2014), "Numerical investigation of H-shaped short steel piles with localized severe corrosion", Eng. Struct., 73, 114-124. https://doi.org/10.1016/j.engstruct.2014.04.048.
  29. Stefec, R. and Franz, F. (1978), "A study of the pitting corrosion of cold-worked stainless steel", Corros. Sci., 18, 161-168. https://doi.org/10.1016/S0010-938X(78)80086-9
  30. Wang, H., Yu, Y., Yu, J.X., Duan, H., Zhang, Y., Li, Z.M. and Wang, C.M. (2018), "Effect of 3D random pitting defects on the collapse pressure of pipe-Part I: Experiment", Thin-Wall. Struct., 129, 512-526. https://doi.org/10.1016/j.tws.2018.04.015.
  31. Wang, Y., Xu, S. and Li A. (2020b), "Flexural performance evaluation of corroded steel beam based on 3D corrosion morphology", Struct. Infrastruct. Eng., (4), 1-16. https://10.1080/15732479.2020.1713169.
  32. Wang, Y., Xu, S., Li, H. and Zhang, H. (2020a), "Surface characteristics and stochastic model of corroded structural steel under general atmospheric environment", Acta Metall. Sin., 56(2), 148-160. https://10.11900/0412.1961.2019.00156.
  33. Wang, Y., Xu, S., Wang, H. and Li, A. (2017), "Predicting the residual strength and deformability of corroded steel plate based on the corrosion morphology", Constr. Build. Mater., 152, 777-793. https://doi.org/10.1016/j.conbuildmat.2017.07.035.
  34. Wu, H., Lei, H., Chen, Y.F. and Qiao, J. (2019), "Comparison on corrosion behaviour and mechanical properties of structural steel exposed between urban industrial atmosphere and laboratory simulated environment", Constr. Build. Mater, 211, 228-243. https://doi.org/10.1016/j.conbuildmat.2019.03.207.
  35. Xu, S., Zhang, Z. and Qin, G. (2019b), "Study on the seismic performance of corroded H-shaped steel columns", Eng. Struct., 191, 39-61. https://doi.org/10.1016/j.engstruct.2019.04.037.
  36. Xu, S., Zhang, Z., Li, R. and Wang, H. (2019a), "Effect of cleaned corrosion surface topography on mechanical properties of cold-formed thin-walled steel", Constr. Build. Mater., 222, 1-14. https://doi.org/10.1016/j.conbuildmat.2019.06.130.
  37. Zhang, Z., Xu, S. and Li, R. (2020a), "Comparative investigation of the effect of corrosion on the mechanical properties of different parts of thin-walled steel", Thin-Wall. Struct., 146, 106450, https://10.1016/j.tws.2019.106450.
  38. Zhang, Z., Xu, S., Nie, B. and Xing Z. (2020b), "Experimental and numerical investigation of corroded steel columns subjected to in-plane compression and bending", Thin-Wall. Struct., 151, 106735, https://10.1016/j.tws.2020.106735.
  39. Zhou, X. and Chen, M. (2018), "Experimental investigation and finite element analysis of web-stiffened cold-formed steel columns with batten sheets", Thin-Wall. Struct., 125, 38-50. https://doi.org/10.1016/j.tws.2018.01.006.

피인용 문헌

  1. Seismic performance of steel columns corroded in general atmosphere vol.40, pp.2, 2020, https://doi.org/10.12989/scs.2021.40.2.217
  2. Predicting seismic performance of locally corroded steel box-section piers vol.40, pp.5, 2020, https://doi.org/10.12989/scs.2021.40.5.709