Computers and Concrete

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Enhancing the performance of hyposludge concrete beams using basalt fiber and latex under cyclic loading

  • Srividhya, S. (Department of Civil Engineering, College of Engineering Guindy, Anna University) ;
  • Vidjeapriya, R. (Department of Civil Engineering, College of Engineering Guindy, Anna University) ;
  • Neelamegam, M. (Department of Civil Engineering, Easwari Engineering College)
  • Received : 2020.11.15
  • Accepted : 2021.06.11
  • Published : 2021.07.25
⟨ Previous Next ⟩

Abstract

An attempt has been made to study the influence of basalt fiber and latex on the behaviour of hypo sludge based concrete beams under cyclic loading. Two sets of four geometrically similar specimens were cast to study the deflection behaviour of beams. The analysis and study of parameters such as ultimate load carrying capacity, crack pattern, energy dissipation, stiffness degradation and ductility were conducted in this investigation. A preliminary investigation showed that the durability properties decreased when hypo sludge was added to concrete. To enhance the durability, SBR latex was added to one set of four specimens. Results indicate that the addition of basalt fibers and latex to the hypo sludge based concrete beams showed significant improvement in ultimate load carrying capacity, stiffness, energy dissipation and ductility compared to the control concrete beams. The specimen (LHSBFC) with 10% hypo sludge, 0.25% Basalt fiber and 10% SBR latex showed an increase of 1.82% load carrying capacity, 2.65% stiffness, 21.84% ductility, 16% energy dissipation when compared to the control concrete beam.

Keywords

Acknowledgement

The authors would like to acknowledge all the support from Tech Civil Material Testing Laboratory Pvt Ltd.

References

  1. Ahmad, S., Malik, M.I., Wani, M.B. and Ahmad, R. (2013), "Study of concrete involving use of waste paper sludge ash as partial replacement of cement", IOSR J. Eng., 3(11), 6-15.
  2. Ali, B., Raza, S.S., Hussain, I. and Iqbal, M. (2021), "Influence of different fibers on mechanical and durability performance of concrete with silica fume", Struct. Concrete, 22(1), 318-333. https://doi.org/10.1002/suco.201900422.
  3. Ali, M. and Chouw, N. (2013), "Experimental investigations on coconut-fiber rope tensile strength and pullout from coconut fiber reinforced concrete", Constr. Build. Mater., 41, 681-690. https://doi.org/10.1016/j.conbuildmat.2012.12.052.
  4. Alnahhal, W. and Aljidda, O. (2018), "Flexural behavior of basalt fiber reinforced concrete beams with recycled concrete coarse aggregates", Constr. Build. Mater., 169, 165-178. https://doi.org/10.1016/j.conbuildmat.2018.02.135.
  5. Amran, M., Murali, G., Fediuk, R., Vatin, N., Vasilev, Y. and Abdelgader, H. (2021), "Palm oil fuel ash-based eco-efficient concrete: A critical review of the short-term properties", Mater., 14(2), 332. https://doi.org/10.3390/ma14020332.
  6. Ansari, M. and Safiey, A. (2020), "Corrosion effects on mechanical behavior of steel fiber reinforced concrete, including fibers from recycled tires", Comput. Concrete, 26(4), 367-375. https://doi.org/10.12989/cac.2020.26.4.367.
  7. Ansari, M. and Safiey, A. (2021), "Interaction of magnetic water and polypropylene fiber on fresh and hardened properties of concrete", Steel Compos. Struct., 39(3), 307-318. https://doi.org/10.12989/scs.2021.39.3.307.
  8. ASTM C1585-13, Standard Test Method for Measurement of Rate of Absorption of Water by Hydraulic-Cement Concretes.
  9. Ayub, T., Shafiq, N. and Nuruddin, M.F. (2014), "Mechanical properties of high-performance concrete reinforced with basalt fibers", Procedia Eng., 77, 131-139. https://doi.org/10.1016/j.proeng.2014.07.029.
  10. Azizinamini, A., Pavel, R., Hatfield, E. and Ghosh, S.K. (1999), "Behavior of lap-spliced reinforcing bars embedded in high-strength concrete", ACI Struct J., 96, 826-835. https://doi.org/10.14359/737.
  11. Bai, J., Chaipanich, A., Kinuthia, J.M., O'farrell, M., Sabir, B.B., Wild, S. and Lewis, M.H. (2003), "Compressive strength and hydration of waste paper sludge ash-ground granulated blast furnace slag blended pastes", Cement Concrete Res., 33(8), 1189-1202. https://doi.org/10.1016/S0008-8846(03)00042-5.
  12. Beglarigale, A. and Yazici, H. (2015), "Pull-out behavior of steel fiber embedded in flowable RPC and ordinary mortar", Constr. Build. Mater., 75, 255-265. https://doi.org/10.1016/j.conbuildmat.2014.11.037.
  13. Bhat, T., Chevali, V., Liu, X., Feih, S. and Mouritz, A.P. (2015), "Fire structural resistance of basalt fiber composite", Compos. Part A: Appl. Sci. Manuf., 71, 107-115. https://doi.org/10.1016/j.compositesa.2015.01.006.
  14. Bhikshma, V., Jagannadha, R.K. and Balaji, B. (2010), "An experimental study on behavior of polymer cement concrete", Asian J. Civil Eng. (Build. Hous.), 11(5), 563-573.
  15. Branston, J., Das, S., Kenno, S.Y. and Taylor, C. (2016), "Influence of basalt fibers on free and restrained plastic shrinkage", Cement Concrete Compos., 74, 182-190. https://doi.org/10.1016/j.cemconcomp.2016.10.004.
  16. Buratti, N., Ferracuti, B. and Savoia, M. (2013), "Concrete crack reduction in tunnel linings by steel fiber-reinforced concretes", Constr. Build. Mater., 44, 249-259. https://doi.org/10.1016/j.conbuildmat.2013.02.063.
  17. Dadmand, B., Pourbaba, M., Sadaghian, H. and Mirmiran, A. (2020), "Experimental & numerical investigation of mechanical properties in steel fiber-reinforced UHPC", Comput. Concrete, 26(5), 451-465. https://doi.org/10.12989/cac.2020.26.5.451.
  18. Divyah, N., Thenmozhi, R. and Neelamegam, M. (2020), "Experimental and numerical analysis of battened builtup lightweight concrete encased composite columns subjected to axial cyclic loading", Lat. Am. J. Solid. Struct., 17(3). http://dx.doi.org/10.1590/1679-78255745.
  19. Divyah, N., Thenmozhi, R., Neelamegam, M. and Prakash, R. (2021), "Characterization and behavior of basalt fiber-reinforced lightweight concrete", Struct Concrete, 22(1), 422-430. http://doi.org/10.1002/suco.201900390.
  20. Dogan, M. and Bideci, A. (2016), "Effect of Styrene Butadiene Copolymer (SBR) admixture on high strength concrete", Constr. Build. Mater., 112, 378-385. http://doi.org/10.1016/j.conbuildmat.2016.02.204.
  21. Fava, G., Ruello, M. L. and Corinaldesi, V. (2011), "Paper mill sludge ash as supplementary cementitious material", J. Mater. Civil Eng., 23(6), 772-776. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000218.
  22. Ganesan, N. and Indira, P.V. (2000), "Latex modified SFRC beam-column joints subjected to cyclic loading", Ind. Concrete. J., 74(7), 416-420.
  23. Ghamari, A., Kurdi, J., Shemirani, A.B. and Haeri, H. (2020), "Experimental investigating the properties of fiber reinforced concrete by combining different fibers", Comput. Concrete, 25(6), 509-516. https://doi.org/10.12989/cac.2020.25.6.509.
  24. Goel, G. and Kalamdhad, A.S. (2017), "An investigation on use of paper mill sludge in brick manufacturing", Constr. Build. Mater, 148, 334-343. https://doi.org/10.1016/j.conbuildmat.2017.05.087.
  25. Gomes, L.D.D.S., Oliveira, D.R.C.D., MoraesNeto, B.N.D., Medeiros, A.B.D. and Macedo, A.N. (2018), "Experimental analysis of the efficiency of steel fibers on shear strength of beams", Lat. Am. J. Solid. Struct., 15(7). https://doi.org/10.1590/1679-78254710.
  26. High, C., Seliem, H.M., El-Safty, A. and Rizkalla, S.H. (2015), "Use of basalt fibers for concrete structures", Constr. Build. Mater., 96, 37-46. https://doi.org/10.1016/j.conbuildmat.2015.07.138.
  27. IS 383 (2016), Specification for Coarse and Fine Aggregate from Natural Sources for Concrete, Bureau of Indian Standards, New Delhi, India.
  28. IS 516 (1959) (Reaffirmed 2004), Methods of Tests for Strength of Concrete. Amendment No. 2, Reprint 1993, Bureau of Indian Standards, New Delhi, India.
  29. Jalasutram, S., Sahoo, D.R. and Matsagar, V. (2017), "Experimental investigation of the mechanical properties of basalt fiber-reinforced concrete", Struct Concrete, 18(2), 292-302. https://doi.org/10.1002/suco.201500216.
  30. Jittin, V., Minnu, S.N. and Bahurudeen, A. (2020), "Potential of sugarcane bagasse ash as supplementary cementitious material and comparison with currently used rice husk ash", Constr. Build. Mater, 273. https://doi.org/10.1016/j.conbuildmat.2020.121679.
  31. Katkhuda, H. and Shatarat, N. (2017), "Improving the mechanical properties of recycled concrete aggregate using chopped basalt fibers and acid treatment", Constr. Build. Mater., 140, 328-335. https://doi.org/10.1016/j.conbuildmat.2017.02.128.
  32. Kayali, O. (2004), "Effect of high volume fly ash on mechanical properties of fiber reinforced concrete", Struct Constr., 37(5), 318-327. https://doi.org/10.1617/13978.
  33. Khan, M. and Ali, M. (2019), "Improvement in concrete behavior with fly ash, silica-fume and coconut fibers", Constr. Build. Mater, 203, 174-187. https://doi.org/10.1016/j.conbuildmat.2019.01.103.
  34. Kirthika, S.K. and Singh, S.K. (2018), "Experimental investigations on basalt fiber-reinforced concrete", J. Inst. Eng. Ser. A, 99(4), 661-670. https://doi.org/10.1007/s40030-018-0325-4.
  35. Kizilkanat, A.B., Kabay, N., Akyuncu, V., Chowdhury, S. and Akca, A.H. (2015), "Mechanical properties and fracture behavior of basalt and glass fiber reinforced concrete: An experimental study", Constr. Build. Mater., 100, 218-224. https://doi.org/10.1016/j.conbuildmat.2015.10.006.
  36. Larsen, I.L. and Thorstensen, R.T. (2020), "The influence of steel fibers on compressive and tensile strength of ultra high performance concrete, A review", Constr. Build. Mater., 256, 119459. https://doi.org/10.1016/j.conbuildmat.2020.119459.
  37. Lenka, S. and Panda, K.C. (2017), "Effect of metakaolin on the properties of conventional and self compacting concrete", Adv. Concrete Constr., 5(1), 31-48. http://doi.org/10.12989/acc.2017.5.1.031.
  38. Mills, R.H. (1981), "Preferential precipitation of calcium hydroxide on alkali-resistant glass fibers", Cement Concrete Res., 11(5), 689-697. https://doi.org/10.1016/0008-8846(81)90027-2.
  39. Mohammadyan-Yasouj, S.E. and Ghaderi, A. (2020), "Experimental investigation of waste glass powder, basalt fiber, and carbon nanotube on the mechanical properties of concrete", Constr. Build. Mater., 252, 119115. https://doi.org/10.1016/j.conbuildmat.2020.119115.
  40. Mohammed, B.S. and Fang, O.C. (2011), "Mechanical and durability properties of concretes containing paper-mill residuals and fly ash", Constr. Build. Mater., 25(2), 717-725. https://doi.org/10.1016/j.conbuildmat.2010.07.015.
  41. Mosaberpanah, M.A., Amran, Y.H. and Akoush, A. (2020), "Performance investigation of palm kernel shell ash in high strength concrete production", Comput. Concrete, 26(6), 577-585. https://doi.org/10.12989/cac.2020.26.6.577.
  42. Muduli, R. and Mukharjee, B.B. (2019), "Effect of incorporation of metakaolin and recycled coarse aggregate on properties of concrete", J. Clean. Prod., 209, 398-414. https://doi.org/10.1016/j.jclepro.2018.10.221.
  43. Murugesan, T., Vidjeapriya, R. and Bahurudeen, A. (2020), "Sugarcane bagasse ash-blended concrete for effective resource utilization between sugar and construction industries", Sugar Tech., 858-869. https://doi.org/10.1007/s12355-020-00794-2.
  44. Murugesan, T., Vidjeapriya, R. and Bahurudeen, A. (2020), "Sustainable use of sugarcane bagasse ash and marble slurry dust in crusher sand based concrete", Struct. Concrete, 22(S1), 183-192. https://doi.org/10.1002/suco.202000215.
  45. Pillay, D.L., Olalusi, O.B. and Mostafa, M.M. (2020), "A review of the engineering properties of concrete with paper mill waste ash towards sustainable rigid pavement construction", Silicon, 1-17. https://doi.org/10.1007/s12633-020-00664-2.
  46. Qureshi, L.A., Ali, B. and Ali, A. (2020), "Combined effects of supplementary cementitious materials (silica fume, GGBS, fly ash and rice husk ash) and steel fiber on the hardened properties of recycled aggregate concrete", Constr. Build. Mater., 263, 120636. https://doi.org/10.1016/j.conbuildmat.2020.120636.
  47. Ramli, M., Tabassi, A.A. and Hoe, K.W. (2013), "Porosity, pore structure and water absorption of polymer-modified mortars: An experimental study under different curing conditions", Compos. Part B: Eng., 55, 221-233. http://doi.org/10.1016/j.compositesb.2013.06.022.
  48. Ridzuan, A.R.M., Fauzi, M.A., Ghazali, E., Arshad, M.F. and Fauzi, M.A.M. (2011), "Strength assessment of controlled low strength materials (CLSM) utilizing recycled concrete aggregate and waste paper sludge ash", IEEE Colloquium on Humanities, Science and Engineering, 208-211.
  49. Rossignolo, J.A. (2009), "Interfacial interactions in concretes with silica fume and SBR latex", Constr. Build. Mater., 23(2), 817-821. https://doi.org/10.1016/j.conbuildmat.2008.03.005.
  50. Sakai, E. and Sugita, J. (1995), "Composite mechanism of polymer modified cement", Cement Concrete Res., 25(1), 127-135. https://doi.org/10.1016/0008-8846(94)00120-N.
  51. Schneider, M. (2019), "The cement industry on the way to a low-carbon future", Cement Concrete Res., 124, 105792. https://doi.org/10.1016/j.cemconres.2019.105792
  52. Shankar, G.R. and Suji, D. (2014), "Seismic behaviour of exterior reinforced concrete beam-column joints in high performance concrete using metakaolin and partial replacement with quarry dust", International Scholarly Research Notices. http://doi.org/10.1155/2014/361962.
  53. Sharipudin, S.S. and Ridzuan, A.R.M. (2013), "Influence of waste paper sludge ash (WPSA) and fine recycled concrete aggregate (FRCA) on the compressive strength characteristic of foamed concrete", Adv. Mater. Res., 626, 376-380. https://doi.org/10.4028/www.scientific.net/AMR.626.376.
  54. Siddiqi, Z.A., Hameed, R., Saleem, M., Khan, Q.S. and Qazi, J.A. (2013), "Determination of compressive strength and water absorption of styrene butadiene rubber (SBR) latex modified concrete", Pak. J. Sci., 65(1), 124.
  55. Singh, L.P., Ali, D., Tyagi, I., Sharma, U., Singh, R. and Hou, P. (2019), "Durability studies of nano-engineered fly ash concrete", Constr. Build. Mater., 194, 205-215. https://doi.org/10.1016/j.conbuildmat.2018.11.022.
  56. Singh, N.B. and Middendorf, B. (2020), "Geopolymers as an alternative to Portland cement: An overview", Constr. Build. Mater., 237, 117455. https://doi.org/10.1016/j.conbuildmat.2019.117455.
  57. Sukontasukkul, P., Pomchiengpin, W. and Songpiriyakij, S. (2010), "Post-crack (or post-peak) flexural response and toughness of fiber reinforced concrete after exposure to high temperature", Constr. Build. Mater., 24(10), 1967-1974. https://doi.org/10.1016/j.conbuildmat.2010.04.003.
  58. Sultana, N., Hossain, S.Z., Alam, M.S., Hashish, M.M.A. and Islam, M.S. (2020), "An experimental investigation and modeling approach of response surface methodology coupled with crow search algorithm for optimizing the properties of jute fiber reinforced concrete", Constr. Build. Mater., 243, 118216. https://doi.org/10.1016/j.conbuildmat.2020.118216.
  59. Tamanna, K., Raman, S.N., Jamil, M. and Hamid, R. (2020), "Utilization of wood waste ash in construction technology: A review", Constr. Build. Mater., 237, 117654. https://doi.org/10.1016/j.conbuildmat.2019.117654.
  60. Tassew, S.T. and Lubell, A.S. (2014), "Mechanical properties of glass fiber reinforced ceramic concrete", Constr. Build. Mater., 51, 215-224. https://doi.org/10.1016/j.conbuildmat.2013.10.046.
  61. Tawfik, A.S., Badr, M.R. and Elzanaty, A. (2014), "Behavior and ductility of high strength reinforced concrete frames", HBRC J., 10(2), 215-221. https://doi.org/10.1016/j.hbrcj.2013.11.005.
  62. Truong, G.T., Son, M.K. and Choi, K.K. (2019), "Mechanical performance and durability of latex-modified fiber-reinforced concrete", J. Adv. Concrete Technol., 17(2), 79-92. https://doi.org/10.3151/jact.17.79.
  63. Wang, W. and Chouw, N. (2017), "The behaviour of coconut fiber reinforced concrete (CFRC) under impact loading", Constr. Build. Mater., 134, 452-461. https://doi.org/10.1016/j.conbuildmat.2016.12.092.
  64. Wong, H.S., Barakat, R., Alhilali, A., Saleh, M. and Cheeseman, C.R. (2015), "Hydrophobic concrete using waste paper sludge ash", Cement Concrete Res., 70, 9-20. https://doi.org/10.1016/j.cemconres.2015.01.005.
  65. Xiaochun, Q., Xiaoming, L. and Xiaopei, C. (2017), "The applicability of alkaline-resistant glass fiber in cement mortar of road pavement: Corrosion mechanism and performance analysis", Int. J. Pavement Res. Technol., 10(6), 536-544. https://doi.org/10.1016/j.ijprt.2017.06.003.
  66. Zhou, M., Fang, D. and Jiang, D. (2016), "Research on the fracture properties and modification mechanism of polyester fiber and SBR latex modified cement concrete", Adv. Mater. Sci. Eng., 2016, Article ID 5163702. https://doi.org/10.1155/2016/5163702.