DOI QR코드

DOI QR Code

Experimental and numerical study on the stability of slurry shield tunneling in circular-gravel layer with different cover-span ratios

  • Liu, Xinrong (School of Civil Engineering, Chongqing University) ;
  • Liu, Dongshuang (School of Civil Engineering, Chongqing University) ;
  • Xiong, Fei (School of Civil Engineering, Chongqing University) ;
  • Han, Yafeng (School of Civil Engineering, Chongqing University) ;
  • Liu, Ronghan (School of Civil Engineering, Chongqing University) ;
  • Meng, Qingjun (Nanning Rail Transit Co., Ltd) ;
  • Zhong, Zuliang (School of Civil Engineering, Chongqing University) ;
  • Chen, Qiang (School of Civil Engineering, Chongqing University) ;
  • Weng, Chengxian (T.Y. Lin International Engineering Consulting (China) Co., Ltd) ;
  • Liu, Wenwu (School of Civil Engineering, Chongqing University)
  • 투고 : 2020.08.28
  • 심사 : 2021.12.22
  • 발행 : 2022.02.10

초록

A set of slurry shield test system capable of cutter cutting and slurry automatic circulation is used to investigate the deformation characteristics, the evolution characteristics of support resistance and the distribution and evolution process of earth pressure during excavating and collapsing of slurry shield tunneling in circular-gravel layer. The influence of cover-span ratio on surface subsidence, support resistance and failure mode of excavation face is also discussed. Three-dimensional numerical calculations are performed to verify the reliability of the test results. The results show that, with the decrease of the supporting force of the excavation face, the surface subsidence goes through four stages: insensitivity, slow growth, rapid growth and stability. The influence of shield excavation on the axial earth pressure of the front soil is greater than that of the vertical earth pressure. When the support resistance of the excavation face decreases to the critical value, the soil in front of the excavation face collapses. The shape of the collapse is similar to that of a bucket. The ultimate support resistance increase with the increase of the cover-span ratio, however, the angle between the bottom of the collapsed body and the direction of the tunnel excavation axis when the excavation face is damaged increase first and then becomes stable. The surface settlement value and the range of settlement trough decrease with the increase of cover-span ratio. The numerical results are basically consistent with the model test results.

키워드

과제정보

The research described in this paper was financially supported by the National Key R&D Program of China (Grant No. 2018YFC1504802), National Natural Science Foundation for Young Scientists of China (Grant No. 52104076) and the National Natural Science Foundation of China (Grant No. 52074042).

참고문헌

  1. Alagha, A.S.N. and Chapman, D.N. (2019), "Numerical modelling of tunnel face stability in homogeneous and layered soft ground", Tunn. Undergr. Sp. Tech., 94, 103096. https://doi.org/10.1016/j.tust.2019.103096.
  2. Anagnostou, G. and Kovari, K. (1994), "The face stability of slurry-shield-driven tunnels", Tunn. Undergr. Sp. Tech.,9(2), 165-174. https://doi.org/10.1016/0886-7798(94)90028-0.
  3. Anagnostou, G. and Kovari, K. (1996), "Face stability conditions with earth-pressure-balanced shields", Tunn. Undergr. Sp. Tech., 11(2), 165-173. https://doi.org/10.1016/0886-7798(96)00017-X.
  4. Babendererde, S. (1991), "Tunnelling machines in soft ground: a comparison of slurry and EPB shield systems", Tunn. Undergr. Sp. Tech., 6(2), 169-174. https://doi.org/10.1016/0886-7798(91)90063-A.
  5. Broere, W. (1998), "Face stability calculation for a slurry shield in heterogeneous soft soils", Proceedings of the World Tunnel Congress 98 on Tunnels and Metropolises, Sao Paolo, Brazil, April.
  6. Broere, W. and van Tol, A.F. (2001), "Time-dependant infiltration and groundwater flow in a face stability analysis", Proceedings of the International Symposium on Modern Tunneling Science and Technology, Kyoto, Japan, October.
  7. Chaipanna, P. and Jongpradist, P. (2019), "3D response analysis of a shield tunnel segmental lining during construction and a parametric study using the ground-spring model", Tunn. Undergr. Sp. Tech., 90, 369-382. https://doi.org/10.1016/j.tust.2019.05.015.
  8. Chou, H.S., Yang, C.Y., Hsieh, B.J. and Chang, S.S. (2001), "A study of liquefaction related damages on shield tunnels", Tunn. Undergr. Sp. Tech., 16(3), 185-193. https://doi.org/10.1016/S0886-7798(01)00057-8.
  9. Editorial Department of China Journal of Highway and Transport. (2015), "Review on China's Tunnel Engineering Research", Chin. J. Highway Transport., 28(5), 1-65. https://doi.org/10.19721/j.cnki.1001-7372.2015.05.001.
  10. Eisenstein, Z. and Ezzeldine, O. (1992), "The effect of tunnelling technology on ground control", Tunn. Undergr. Sp. Tech., 7(3), 273-279. https://doi.org/10.1016/0886-7798(92)90008-6.
  11. Eskandari, F., Goharrizi, K.G. and Hooti, A. (2018), "The impact of EPB pressure on surface settlement and face displacement in intersection of triple tunnels at Mashhad metro", Geomech. Eng., 15(2), 769-774. https://doi.org/10.12989/gae.2018.15.2.769.
  12. Han, Y.F., Liu, X.R., Li, D.L., Tu, Y.L., Deng, Z.Y., Liu, D.S. and Wu, X.C. (2019), "Model test on the bearing behaviors of the tunnel-type anchorage in soft rock with underlying weak interlayers", B. Eng. Geol. Environ., 79(2), 1023-1040. https://doi.org/10.1007/s10064-019-01564-5.
  13. Huang, F., Zhang, M., Wang, F., Ling, T. and Yang, X. (2020), "The failure mechanism of surrounding rock around an existing shield tunnel induced by an adjacent excavation", Comput. Geotec., 117, https://doi.org/10.1016/j.compgeo.2019.103236.
  14. Jeon, Y.J., Jeon, S.C., Jeon, S.J. and Lee, C.J. (2020), "Study on the behaviour of pre-existing single piles to adjacent shield tunnelling by considering the changes in the tunnel face pressures and the locations of the pile tips", Geomech. Eng., 21(2), 187-200. https://doi.org/10.12989/gae.2020.21.2.187.
  15. Jallow, A., Ou, C.Y. and Lim, A. (2019), "Three-dimensional numerical study of long-term settlement induced in shield tunneling", Tunn. Undergr. Sp. Tech., 88, 221-232. https://doi.org/10.1016/j.tust.2019.02.021.
  16. Kim, K., Oh, J., Lee, H., Kim, D. and Choi, H. (2018), "Critical face pressure and backfill pressure in shield TBM tunneling on soft ground", Geomech. Eng., 15(3), 823-831. https://doi.org/10.12989/gae.2018.15.3.823.
  17. Kim, D., Pham, K., Park, S., Oh, J.Y. and Choi, H. (2020), "Determination of effective parameters on surface settlement during shield TBM", Geomech. Eng., 21(2), 153-164. https://doi.org/10.12989/gae.2020.21.2.153.
  18. Kupferle, J., Zizka, Z., Schoesser, B., Rottger, A., Alber, M., Thewes, M. and Theisen, W. (2018), "Influence of the slurrystabilized tunnel face on shield TBM tool wear regarding the soil mechanical changes-Experimental evidence of changes in the tribological system", Tunn. Undergr. Sp. Tech., 74, 206-216. https://doi.org/10.1016/j.tust.2018.01.011.
  19. Li, Y., Emeriault, F., Kastner, R. and Zhang, Z.X. (2009), "Stability analysis of large slurry shield-driven tunnel in soft clay", Tunn. Undergr. Sp. Tech., 24(4), 472-481. https://doi.org/10.1016/j.tust.2008.10.007.
  20. Liu, X.R., Han, Y.F., Li, D.L., Tu, Y.L., Deng, Z.Y., Yu, C.T. and Wu, X.C. (2019), "Anti-pull mechanisms and weak interlayer parameter sensitivity analysis of tunnel-type anchorages in soft rock with underlying weak interlayers", Eng. Geol., 253, 123-136. https://doi.org/10.1016/j.enggeo.2019.03.012.
  21. Liu, X.R., Xiong, F., Zhou, X.H., Liu, D.S., Chen, Q., Zhang, J.L., Han, Y.F., Xu, B., Deng, Z.Y. and He, C.M. (2021), "Physical model test on the influence of the cutter head opening ratio on slurry shield tunnelling in a cobble layer", Tunn. Undergr. Sp. Tech., 104264. https://doi.org/10.1016/j.tust.2021.104264.
  22. Liu, D.S., Liu, X.R., Lin, C.Q., Xiong, F., Han, Y.F., Meng, Q.J., Zhong, Z.L., Chen, Q. and Weng, C.X. (2020), " Experimental study and engineering application of slurry permeability mechanism of slurry shield in circular-gravel stratum", Arab. J. Geosci., 13(9), 1000. https://doi.org/10.1007/s12517-020-05731-x.
  23. Li, J.Y., Liu, W., Zou, J.J., Zhao, Y. and Gong, X.N. (2018), "Large-scale model tests on face instability of shallow shield tunnels in sand", Chin. J. Geotech. Eng., 40(3), 562-567. https://doi.org/10.11779/CJGE201803022.
  24. Lu, X.L., Zhou, Y.C. and Li, F.D. (2016), "Centrifuge model test and numerical simulation of stability of excavation face of shield tunnel in silty sand", Rock Soil Mech., 37(11), 3324-3328. https://doi.org/10.16285/j.rsm.2016.11.035.
  25. Maid, U. (1992), "Design features of the Botlek rail tunnel in the Betuweroute", Tunn. Undergr. Sp. Tech., 14(2), 135-140. https://doi.org/10.1016/S0886-7798(99)00027-9.
  26. Mansour, M. and Swoboda, G. (1997), "Tunnel face stability of hydroshield tunneling", Proceedings of the 9th International Conference on Computer Methods and Advances in Geomechanics, Wuhan, China, November.
  27. Naseem, A., Schotte, K., De Pauw, B. and De Backer, H. (2019), "Ground Settlements due to Construction of Triplet Tunnels with Different Construction Arrangements", Adv. Civ. Eng., 1-18. https://doi.org/10.1155/2019/8637837.
  28. Park, H., Oh, J.Y., Kim, D. and Chang, S. (2018), "Monitoring and analysis of ground settlement induced by tunnelling with slurry pressure-balanced tunnel boring machine", Adv. Civ. Eng., 1-10. https://doi.org/10.1155/2018/5879402.
  29. Swoboda, G. and Abu-Krisha, A. (1999), "Three-dimensional numerical modelling for TBM tunnelling in consolidated clay", Tunn. Undergr. Sp. Tech., 14(3), 327-333. https://doi.org/10.1016/s0886-7798(99)00047-4.
  30. Smith, A., Dixon, N. and Fowmes, G.J. (2016), "Early detection of first-time slope failures using acoustic emission measurements: large-scale physical modelling", Geotechnique., 67(2), 138-152. https://doi.org/10.1680/jgeot.15.P.200.
  31. Uchida, K., Wasa, Y. and Kanai, M. (1992), "Design of the shield tunnel for the trans-Tokyo bay highway", Tunn. Undergr. Sp. Tech., 7(3), 251-261. https://doi.org/10.1016/0886-7798(92)90006-4.
  32. Wang, S.G., Liu, Y.R., Tao, Z.F., Zhang, Y., Zhong, D.N., Wu Z.S., Lin, C. and Yang, Q. (2018), "Geomechanical model test for failure and stability analysis of high arch dam based on acoustic emission technique", Int. J. Rock Mech. Min., 112, 95-107. https://doi.org/10.1016/j.ijrmms.2018.10.018.
  33. Xu, T. and Bezuijen, A. (2019), "Experimental study on the mechanisms of bentonite slurry penetration in front of a slurry TBM", Tunn. Undergr. Sp. Tech., 93, 103052. https://doi.org/10.1016/j.tust.2019.103052.
  34. Xue, Y.G., Li, X., Qiu, D.H., Ma, X.M., Kong, F.M., Qu, C.Q. and Zhao, Y. (2019), "Stability evaluation for the excavation face of shield tunnel across the Yangtze River by multi-factor analysis", Geomech. Eng., 19(3), 283-293. https://doi.org/10.12989/gae.2019.19.3.283.
  35. Yamaguchi, I., Yamazaki, I. and Kiritani, Y. (1998), "Study of ground-tunnel interactions of four shield tunnels driven in close proximity, in relation to design and construction of parallel shield tunnels", Tunn. Undergr. Sp. Tech., 13(3), 289-304. https://doi.org/10.1016/S0886-7798(98)00063-7.
  36. Zhang, L., Feng, K., Gou, C., He, C., Liang, K. and Zhang, H. (2019), "Failure tests and bearing performance of prototype segmental linings of shield tunnel under high water pressure", Tunn. Undergr. Sp. Tech., 92, 103053. https://doi.org/10.1016/j.tust.2019.103053.
  37. Zhang, F., Gao, Y., Wu, Y. and Wang, Z. (2018), "Face stability analysis of large-diameter slurry shield-driven tunnels with linearly increasing undrained strength", Tunn. Undergr. Sp. Tech., 78, 178-187. https://doi.org/10.1016/j.tust.2018.04.018.
  38. Zhang, ZX., Hu, X.Y. and Scott, K.D. (2011), "A discrete numerical approach for modeling face stability in slurry shield tunnelling in soft soils", Comput. Geotech., 38(1), 94-104. https://doi.org/10.1016/j.compgeo.2010.10.011.
  39. Zeng, S., Lu, X. and Huang, M. (2019), "Discrete element modeling of static liquefaction of shield tunnel face in saturated sand", Acta Geotech., 14(6), 1643-1652. https://doi.org/10.1007/s11440-019-00806-w.
  40. Zizka, Z., Schoesser, B., Thewes, M. and Schanz, T. (2019), "Slurry shield tunneling: New methodology for simplified prediction of increased pore pressures resulting from slurry infiltration at the tunnel face under cyclic excavation processes", Int. J. Civ. Eng., 17(1), 113-130. https://doi.org/10.1007/s40999-018-0303-2.