DOI QR코드

DOI QR Code

Prediction of concrete pumping based on correlation between slump and rheological properties

  • Lee, Jung Soo (Department of Civil and Environmental Engineering, Myungji University) ;
  • Kim, Eun Sung (BieL Inc.) ;
  • Jang, Kyong Pil (Department of Building Research, Korea Institute of Civil Engineering and Building Technology) ;
  • Park, Chan Kyu (Institute of Construction Technology, Samsung C & T Corporation) ;
  • Kwon, Seung Hee (Department of Civil and Environmental Engineering, Myungji University)
  • 투고 : 2021.12.17
  • 심사 : 2022.05.18
  • 발행 : 2022.05.25

초록

This study collected the results of material tests and full-scale pumping tests using 127 types of concrete mixtures with compressive strength ranging from 24 to 200 MPa. The results of 242 material tests showed high correlations between the viscosity of the lubricating layer and concrete, between the slump and the yield stress of concrete, between the water-binder ratio and the viscosity of lubricating layer, and between the time required to reach 500 mm of slump flow and concrete viscosity. Based on these correlations, pumpability was predicted using 101 pumping test conditions, and their accuracy was compared to the actual test results. When the rheological properties of concrete and the lubricating layer were directly measured, the prediction result showed the highest accuracy. A high accuracy can be achieved when the measured viscosity of the lubricating layer, a key determinant of concrete pumpability, is reflected in the prediction of pumpability. When measuring rheological properties is difficult, the slump test can be used to quantitatively predict the pumpability despite the lower accuracy than those of other prediction methods.

키워드

과제정보

This work is supported by the Korea Agency for Infrastructure Technology Advancement (KAIA) grant funded by the Ministry of Land, Infrastructure and Transport (Grant 21TBIP-C158690-02).

참고문헌

  1. ASTM C143. (2010), Standard Test Method for Slump of Hydraulic-Cement Concrete, ASTM International.
  2. ASTM C1611. (2021), Standard Test Method for Slump Flow of Self-Consolidating Concrete, ASTM International.
  3. Bingham, E.C. (1922), Fluidity and Plasticity, McGraw-Hill, New York, New York, USA.
  4. Choi, M.S., Kim, Y.J. and Kwon, S.H. (2013), "Prediction on pipe flow of pumped concrete based on shear-induced particle migration", Cement Concrete Res., 52, 216-224. https://doi.org/10.1016/j.cemconres.2013.07.004.
  5. Choi, M.S., Kim, Y.J., Jang, K.P. and Kwon, S.H. (2014), "Effect of the coarse aggregate size on pipe flow of pumped concrete", Constr. Build. Mater., 66, 723-730. https://doi.org/10.1016/j.conbuildmat.2014.06.027.
  6. Ferraris, C.F. and DeLarrard, F. (1998), "Testing and modeling of fresh concrete rheology", National Institute of Standards and Technology, Gaithersburg, USA. https://doi.org/10.6028/NIST.IR.6094.
  7. Hu, C., de Larrard, F., Sedran, T., Boulay, C., Bosc, F. and Deflorenne, F. (1996), "Validation of BTRHEOM, the new rheometer for soft-to-fluid concrete", Mater. Struct., 29(10), 620-631. https://doi.org/10.1007/BF02485970.
  8. Jang, K.P. (2018), "Design of concrete pumpability based on quantitative predictions", Ph.D. Dissertation of Philosophy, Myong-ji University.
  9. Jang, K.P., Kim, W.J., Choi, M.S. and Kwon, S.H. (2018b), "A new method to estimate rheological properties of lubricating layer for prediction of concrete pumping", Adv. Concrete Constr., 6(5), 465-483. https://doi.org/10.12989/acc.2018.6.5.465.
  10. Jang, K.P., Kwon, S.H., Choi, M.S., Kim, Y.J., Park, C.K. and Shah, S.P. (2018a), "Experimental observation on variation of rheological properties during concrete pumping", Int. J. Concrete Struct. Mater., 12(1), 1-15. https://doi.org/10.1186/s40069-018-0310-3.
  11. Jeong, J.H., Jang, K.P., Park, C.K., Lee, S.H. and Kwon, S. H. (2016), "Effect of admixtures on pumpability for high-strength concrete", ACI Mater. J., 113(3), 323. https://doi.org/10.14359/5168864
  12. Jo, S.D., Park, C.K., Jeong, J.H., Lee, S.H. and Kwon, S.H. (2012), "A computational approach to estimating a lubricating layer in concrete pumping", Comput. Mater. Continua, 27(3), 189.
  13. KCI-UC109. (2019), Standard Test Method for Rheology of Concrete : Vane Rotation Method, Korea Concrete Institute.
  14. KCI-UC110. (2019), Standard Test Method for Rheology of Lubricating Layer in Pipe during Concrete Pumping Cylinder Rotation Method, Korea Concrete Institute.
  15. Kim, J.H., Yim, H.J. and Kwon, S.H. (2014), "Quantitative measurement of the external and internal bleeding of conventional concrete and SCC", Cement Concrete Compos., 54, 34-39. https://doi.org/10.1016/j.cemconcomp.2014.05.006.
  16. Kim, J.S., Kwon, S.H., Jang, K.P. and Choi, M.S. (2018), "Concrete pumping prediction considering different measurement of the rheological properties", Constr. Build. Mater., 171, 493-503. https://doi.org/10.1016/j.conbuildmat.2018.03.194.
  17. Koehler, E.P. and Fowler, D.W. (2009), "Comparison of workability test methods for self-consolidating concrete", J. ASTM Int., 7(2), 1-19.
  18. Kwon, S.H., Jang, K.P. and Lee, J.S. (2021), "External Injection Method for Improvement of Concrete Pumpability", ACI Mater. J., 118(5), 17-28.
  19. Kwon, S.H., Jo, S.D., Par, C.K., Jeong, J.H. and Lee, S.H. (2013a), "Prediction of concrete pumping: Part I. Development of a new tribometer to measure rheological properties of lubricating layer", ACI Mater. J., 110(6), 647-655.
  20. Kwon, S.H., Par, C.K., Jeong, J.H., Jo, S.D. and Lee, S.H. (2013b), "Prediction of concrete pumping: Part II-Analytical prediction and experimental verification", ACI Mater. J., 110(6), 657.
  21. Le, H.D., Kadri, E.H., Aggoun, S., Vierendeels, J., Troch, P. and De Schutter, G. (2015), "Effect of lubrication layer on velocity profile of concrete in a pumping pipe", Mater. Struct., 48(12), 3991-4003. https://doi.org/10.1617/s11527-014-0458-5.
  22. Lee, H.J., Kim, J.H., Moon, J.H., Kim, W.W. and Seo, E.A. (2020), "Experimental analysis on rheological properties for control of concrete extrudability", Adv. Concrete Constr., 9(1), 93-102. https://doi.org/10.12989/acc.2020.9.1.093.
  23. Lee, J.S. (2020), "Research on a method to improve concrete pumpability by external injection of friction reducing agent", Ph.D. Dissertation of Philosophy, Myong-ji University.
  24. Lee, J.S., Jang, K.P., Park, C.K. and Kwon, S.H. (2018), "Verification on effect of external injection of activation agent for lubrication layer through full-scale concrete pumping test", J. Korea Concrete Inst., 30(6), 649-655. https://doi.org/10.4334/jkci.2018.30.6.649
  25. Lee, K.W., Lee, H.J. and Choi, M.S. (2019), "Evaluation of 3D concrete printing performance from a rheological perspective", Adv. Concrete Constr., 8(2), 155-163. https://doi.org/10.12989/acc.2019.8.2.155.
  26. Murata, J. and Kukawa, H. (1992), "Viscosity equation for fresh concrete", Mater. J., 89(3), 230-237.
  27. Nehdi, M. and Al-Martini, S. (2009), "Coupled effects of high temperature, prolonged mixing time, and chemical admixtures on rheology of fresh concrete", ACI Mater. J., 106(3), 231.
  28. Park, C.K., Jang, K.P., Jeong, J.H., Sohn, Y.S. and Kwon, S.H. (2020), "Analysis on pressure losses in pipe bends based on real-scale concrete pumping tests", ACI Mater. J., 117(3), 205-216.
  29. Roussel, N. and Coussot, P. (2005), "Fifty-cent rheometer" for yield stress measurements: from slump to spreading flow", J. Rheol., 49(3), 705-718. https://doi.org/10.1122/1.1879041.
  30. Shin, T.Y., Han, S.H. and Kim, J.H. (2020), "Estimation of yield stress and plastic viscosity of concrete using the slump flow test", J. Korea Concrete Inst., 32(2), 165-171. https://doi.org/10.4334/JKCI.2020.32.2.165.