DOI QR코드

DOI QR Code

Structural performance evaluation of bolted end-plate connections in a half-through railway inclined girder

  • Jung Hyun Kim (Department of Civil and Environmental Engineering, Chung-Ang University) ;
  • Chang Su Shim (Department of Civil and Environmental Engineering, Chung-Ang University)
  • Received : 2023.01.18
  • Accepted : 2023.12.05
  • Published : 2023.12.10

Abstract

A through-railway bridge with an inclined girder has recently been applied to optimize the cross-section of a slender bridge structure in railway bridges. To achieve the additional cross-section optimization effect by the bolted end-plate connection, it is necessary to investigate the application of the bolted end-plate tension connection between the inclined girder and the crossbeam. This basic study was conducted on the application of the bolted end-plate moment connection of crossbeams to half-through girders with inclined webs. The combined behavior of vertical deflection and rotational behavior was observed due to the effect of the web inclination in the inclined girder where the steel crossbeam was connected to the girder by the bolted end-plate moment connection. Therefore, in the experiment, the deflection of the inclined girder was 1.77-2.93 times greater than that of the vertical girder but the lateral deflection of the inclined girder was 0.4 times less than that of the vertical girder. Moreover, the tensile stress of the upper bolts in the inclined girder with low crossbeams was clearly 0.81 times lower than that of the vertical girder. According to the results, the design formula for vertical girders does not reflect the influence of the web inclination. Therefore, this study proposed the design procedures for the inclined girder to apply the bolted end-plate moment connection of the crossbeam to the inclined girder by reflecting the design change factors according to the effect of the web inclination.

Keywords

References

  1. AASHTO (2020), LRFD Bridge Construction Specifications, (9th Edition), American Association of State Highway and Transportation Officials; Washington, DC, USA.
  2. ABAQUS (2014), Analysis User's Manual IV. Version 6.14. USA: ABAQUS, Inc., Dassault Systemes.
  3. AISC (2004), Steel Design Guide 4, Extended End-Plate Moment Connections, (Second edition); American Institute of Steel Construction, Chicago, Illinois, USA.
  4. AREMA (2019), Manual for Railway Engineering, chapter 15. American Railway Engineering and Maintenance of Way Association; Lanham, Maryland, USA.
  5. Bahaari, M.R. and Sherbourne, A.N. (1996a), "Structural behavior of end-plate bolted connections to stiffened columns", J. Struct. Eng., 122(8), 926-935. https://doi.org/10.1061/(ASCE)0733-9445(1996)122:8 (926).
  6. Bahaari, M.R. and Sherbourne, A.N. (1996b), "3D simulation of bolted connections to unstiffened columns-II. Extended endplay connections", J. Construct. Steel Res. Appl. Sci., 40(3), 189-223. https://doi.org/10.1016/S0143-974X(96) 00049-1.
  7. Borgsmiller, J.T. (1995), "Simplified Method for Design of Moment End-Plate Connections", M.S. Thesis, Department of Civil Engineering, Virginia Polytechnic Institute and State University, Blacksburg, Virginia.
  8. BS-5400-3 (2000), Steel, Concrete and Composite Bridges - Part 3: Code of Practice for Design of Steel Bridges, British Standards Institution, London.
  9. EN1993-1-8, Eurocode 3 (2005), Design of Steel Structures - Part 1-8: Design of joints, European Committee for Standardization, Brussels, Belgium.
  10. Douty, R.T. and Mc Guire, W. (1963), "Research on bolted moment connections-A progress report", Proceedings of the 1963 AISC National Engineering Conference, Tulsa, April 24-26, 1963, AISC, 48-55.
  11. Douty, R.T. and McGuire, W. (1965), "High strength bolted moment connections", J. Struct. Div., ASCE, 91(2), 101-128. https://doi.org/10.1061/jsdeag.0001230.
  12. Ronald, D.Z. (2010), "Guide to Stability Design Criteria for Metal Structures", Wiley-Interscience https://doi.org/10.1002/9780470549087.ch2.
  13. Japanese Society of Steel Construction (2004), "Recommendation for Design of High Strength Tensile Bolted Connections for Steel Bridges", JSS IV-05 2004.
  14. John, F.U. (2018), Design and Construction of Modern Steel Railway Bridges, CRC Press, Taylor & Francis Group, LLC.
  15. Kato, B. and McGuire, W. (1973), "Analysis of T-stub flange-to-column connections", J. Struct. Div., 99(5), 865-888. https://doi.org/10.1061/jsdeag.0003510.
  16. Kennedy, N.A., Vinnakota, S. and Sherbourne, A.N. (1981), "The split-tee analogy in bolted splices and beam-column connections", Proceedings of the International Conference: Joints in Structural Steelwork: The Design and Performance of Semi-Rigid and Rigid Joints in Steel and Composite Structures and Their Influence on Structural Behaviour, Teesside Polytechnic, Middlesbrough, Cleveland, England, April 6-9, 1981, 2.138-2.157.
  17. KOBEC (2019), Yeongdong-line between Beopjeon and Bonghwa near 36.972km Chunyangcheon 2nd Bridge Improvement project report, Seongnam, KOBEC, Gyeonggi-do, Republic of Korea, (in Korean).
  18. Korea Construction Standards Center (2019), Design Criteria for Steel Bridges (Allowable stress design, KDS 24 14 30: 2019), Ministry of Land, Infrastructure and Transportation, Sejong, Republic of Korea, (in Korean).
  19. Kuhlmann Ulrike., Breunig Stephanie., Zinke Tim. (2018), "Modern railway bridges as thick plate trough bridges optimization of the design for fatigue and life cycle consideration, optimization of the design for fatigue and life cycle consideration", Stahlbau, 2018; Volume 87, Issue 6: 531-638, (in Germany). https://doi.org/10.1002/stab.201810616.
  20. Network Rail (2010), Technical User Manual for Standard Half Through Underbridges Z-Type Standard Detail and Design Drawings, NR/CIV/TUM/1200 Rev D May 2010, Network Rail, London, UK.
  21. Oliver Hechler, Andreas Girkes (2007), "Efficient reconstruction of bridges with small and medium spans", IABSE Symposium Report,
  22. RTRI (2019), Design Standards for Railway Structures, etc. Steel and Composite Structure, p243~245, Japan Railway Technology Research Institute, (In Japan).
  23. SCI Publication P318 (2004), Design Guide for Steel Railway Bridges, The Steel Construction Institute, Silwood Park, Ascot Berkshire, UK.
  24. Sumner, E.A. (2003), "Unified Design of Extended End-Plate Moment Connections Subject to Cyclic Loading", Ph.D. Dissertation, Virginia Polytechnic Institute and State University, Blacksburg, Virginia.
  25. Ulrike, K., Stephanie, B., Thomas, U., Philipp, W. (2018), "Development of a DASt guideline for higher-frequency hammering processes", Stahlbau, 87(10), 967-983, (in Germany) https://doi.org/10.1002/stab.201800021.
  26. Ulrike, K., Stephanie, B. and Tim, Z. (2018), "Modern railway bridges as thick sheet metal trough bridges - optimization of the design for fatigue and life cycle consideration", Stahlbau, 87(6) 571-582. https://doi.org/10.1002/stab.201810616.
  27. VDEI (2019), Thick Sheet Metal Bridges (Trough bridges with thick deck) Notes on planning and execution, VDEI-INFO Konstruktiver Ingenieurbau Nr. 15 [2019-04], Verband Deutscher Eisebahn-Ivgenieure, Frankfurt, Germany (In Germany).