DOI QR코드

DOI QR Code

The effect of tensile reinforcement on the behavior of CFRP strengthened reinforced concrete beams: An experimental and analytical study

  • Javad Sabzi (Faculty of Engineering, Ferdowsi University of Mashhad) ;
  • M. Reza Esfahani (Faculty of Engineering, Ferdowsi University of Mashhad) ;
  • Togay Ozbakkaloglu (Ingram School of Engineering, Texas State University) ;
  • Ahmadreza Ramezani (Faculty of Engineering, Ferdowsi University of Mashhad)
  • 투고 : 2022.01.12
  • 심사 : 2023.01.02
  • 발행 : 2023.01.10

초록

The present study experimentally and analytically investigates the effect of tensile reinforcement ratio and arrangement on the behavior of FRP strengthened reinforced concrete (RC) beams. The experimental part of the program was comprised of 8 RC beams that were tested under four-point bending. Results have shown that by keeping the total cross-section area of tensile reinforcing bars constant, in specimens with a low reinforcement ratio, increasing the number and decreasing the diameter of bars in the section lead to 21% and 29% increase in the load-carrying capacity of specimens made with normal and high compressive strength, respectively. In specimens with high reinforcement ratio, a different behavior was observed. Furthermore, the accuracy of the existing code provisions and analytical models in predicting the load-carrying capacity of the FRP strengthened beams failed by premature debonding mode were evaluated. Herein, a model is proposed which considers the tensile reinforcement ratio (as opposed to code provisions) to achieve more accurate results for calculating the load carrying capacity of FRP strengthened RC beams.

키워드

과제정보

This research was financially supported by the Ferdowsi University of Mashhad.

참고문헌

  1. ACI 440.2R-02 (2002), Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Reported by ACI Committee 440.
  2. ACI 440.2R-17 (2017), Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, Reported by ACI Committee 440.
  3. ACI 318-19 (2019), Building Code Requirements for Structural Concrete and Commentary, Farmington Hills: American Concrete Institute.
  4. ASTM C39/C39M (2010), Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, American Society for Testing and Materials, West Conshohocken.
  5. ASTM E8/E8M (2009), Standard Test Methods for Tension Testing of Metallic Materials, ASTM E8/E8M, American Society for Testing and Materials, West Conshohocken, PA.
  6. Achintha, M. and Burgoyne, C. (2011), "Fracture mechanics of plate debonding: Validation against experiment", Construct. Build. Mater., 25(6), 2961-2971. https://doi.org/10.1016/j.conbuildmat.2010.11.103.
  7. Aksoylu, C. (2021), "Experimental analysis of shear deficient reinforced concrete beams strengthened by glass fiber strip composites and mechanical stitches", Steel Compos. Struct., 40(2), 267-285. https://doi.org/10.12989/scs.2021.40.2.267.
  8. Al-Saawani, M.A., El-Sayed, A.K. and Al-Negheimish, A.I. (2015), "Effect of basic design parameters on IC debonding of CFRP-strengthened shallow RC beams", J. Reinforc. Plastics Compos., 34(18), 1526-1539. https://doi.org/10.1177/0731684415593816.
  9. Al-Saawani, M.A., El-Sayed, A.K. and Al-Negheimish, A.I. (2020), "Assessment of plate-end debonding design provisions for RC beams strengthened with FRP", Latin Amer. J. Solids Struct., 17(2). https://doi.org/10.1590/1679-78255920.
  10. Ali, L., Ouni, M.H.E., Raza, A. and Kahla, N.B. (2021), "Investigation of FRP-reinforced recycled concrete compressive members: Experimental and theoretical analysis", Steel Compos. Struct., 41(1), 99-113. https://doi.org/10.12989/scs.2021.41.1.099.
  11. Altin, S., Anil, O., Toptas, T. and Kara, M.E. (2011), "Retrofitting of shear damaged RC beams using CFRP strips", Steel Compos. Struct., 11(3), 207-223. http://dx.doi.org/10.12989/scs.2011.11.3.207.
  12. Arabshahi, A., Gharaei-Moghaddam, N. and Tavakkolizadeh, M. (2020), "Development of applicable design models for concrete columns confined with aramid fiber reinforced polymer using Multi-Expression Programming", Structures, 23, 225-244. https://doi.org/10.1016/j.istruc.2019.09.019.
  13. Arabshahi, A., Tavakol, M., Sabzi, J. and Gharaei-Moghaddam, N. (2022), "Prediction of the effective moment of inertia for concrete beams reinforced with FRP bars using an evolutionary algorithm", Structures, 35, 604-705. https://doi.org/10.1016/j.istruc.2021.11.011.
  14. Arduini, M. and Nanni, A. (1997), "Behavior of precracked RC beams strengthened with carbon FRP sheets", J. Compos. Construct., 1(2), 63-70, https://doi.org/10.1061/(ASCE)1090-0268(1997)1:2(63).
  15. Attari, B. and Tavakkolizadeh, M. (2019), "An experimental investigation on effect of elevated temperatures on bond strength between externally bonded CFRP and concrete", Steel Compos. Structures, 32(5), 559-569. https://doi.org/10.12989/scs.2019.32.5.559.
  16. Benjeddou, O., Ouezdou, M.B. and Bedday, A. (2007), "Damaged RC beams repaired by bonding of CFRP laminates", Construct. Build. Mater., 21(6), 1301-1310. https://doi.org/10.1016/j.conbuildmat.2006.01.008.
  17. Brena, S.F. and Macri, B.M. (2004), "Effect of carbon-fiberreinforced polymer laminate configuration on the behavior of strengthened reinforced concrete beams", J. Compos. Construct., 8(3), 229-240. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:3(229).
  18. Ceroni, F. (2010), "Experimental performances of RC beams strengthened with FRP materials", Construct. Build. Mater., 24(9), 1547-1559. https://doi.org/10.1016/j.conbuildmat.2010.03.008.
  19. CNR-DT 200 R1/2013 (2013), Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Existing Structures, Rome, Italy: National Research Council.
  20. De Domenico, D., Urso, S., Borsellino, C., Spinella, N. and Recupero, A. (2020), "Bond behavior and ultimate capacity of notched concrete beams with externally-bonded FRP and PBOFRCM systems under different environmental conditions", Construct. Build. Mater., 265, 121208. https://doi.org/10.1016/j.conbuildmat.2020.121208.
  21. Esfahani, M. Reza, Kianoush, M.R. and Tajari, A.R. (2007), "Flexural behaviour of reinforced concrete beams strengthened by CFRP sheets", Eng. Struct., 29(10), 2428-2444. https://doi.org/10.1016/j.engstruct.2006.12.008.
  22. Farahi, B., Esfahani, M. Reza. and Sabzi, J. (2019), "Experimental investigation on the behavior of reinforced concrete beams retrofitted with NSM-SMA/FRP", Amirkabir J. Civil Eng.. 51(4), 685-698. https://doi.org/10.22060/ceej.2018.13927.5512.
  23. Gao, B., Kim, J.-K. and Leung, C.K. (2004a), "Taper ended FRP strips bonded to RC beams: experiments and FEM analysis", The 2nd international conference on FRP composites in civil engineering.
  24. Gao, B., Kim, J.-K. and Leung, C.K. (2004 b), "Experimental study on RC beams with FRP strips bonded with rubber modified resins", Compos. Sci. Technol., 64(16), 2557-2564. https://doi.org/10.1016/j.compscitech.2004.05.016.
  25. Gholampour, A., Ozbakkaloglu, T. and Hassanli, R. (2017), "Behavior of rubberized concrete under active confinement", Construct. Build. Mater., 138, 372-382. https://doi.org/10.1016/j.conbuildmat.2017.01.105.
  26. ISIS CANADA (2001), Strengthening Reinforced Concrete Structuers with Externally- Bonded Fibre Reinforced Polymers, ISIS Canada.
  27. Khorasani, A.M., Esfahani, M. Reza. and Sabzi, J. (2019), "The effect of transverse and flexural reinforcement on deflection and cracking of GFRP bar reinforced concrete beams", Compos. Part B: Eng., 161, 530-546. https://doi.org/10.1016/j.compositesb.2018.12.127.
  28. Lezgy-Nazargah, M., Dezhangah, M. and Sepehrinia, M. (2018), "The effects of different FRP/concrete bond-slip laws on the 3D nonlinear FE modeling of retrofitted RC beams-A sensitivity analysis", Steel Compos. Struct., 26(3), 347-360. https://doi.org/10.12989/scs.2018.26.3.347.
  29. Lim, J.C., Karakus, M. and Ozbakkaloglu, T. (2016), "Evaluation of ultimate conditions of FRP-confined concrete columns using genetic programming", Comput. Struct., 162, 28-37. https://doi.org/10.1016/j.compstruc.2015.09.005.
  30. Lim, J.C. and Ozbakkaloglu, T. (2015), "Unified stress-strain model for FRP and actively confined normal-strength and highstrength concrete", J. Compos. Construct., 19(4), 04014072. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000536.
  31. Lu, X., Teng, J., Ye, L. and Jiang, J. (2007), "Intermediate crack debonding in FRP-strengthened RC beams: FE analysis and strength model", J. Compos. Construct., 11(2), 161-174. https://doi.org/10.1061/(ASCE)1090-0268(2007)11:2(161).
  32. Maalej, M. and Bian, Y. (2001), "Interfacial shear stress concentration in FRP-strengthened beams", Compos. Struct., 54(4), 417-426, https://doi.org/10.1016/S0263-8223(01)00078-2.
  33. Maalej, M. and Leong, K. (2005), "Effect of beam size and FRP thickness on interfacial shear stress concentration and failure mode of FRP-strengthened beams", Compos. Sci. Technol.. 65(7-8), 1148-1158, https://doi.org/10.1016/j.compscitech.2004.11.010.
  34. Mazzotti, C., Savoia, M. and Ferracuti, B. (2008), "An experimental study on delamination of FRP plates bonded to concrete", Construct. Build. Mater., 22(7), 1409-1421. https://doi.org/10.1016/j.conbuildmat.2007.04.009.
  35. Mostofinejad, D. and Khozaei, K. (2015), "Effect of GM patterns on ductility and debonding control of FRP sheets in RC strengthened beams", Construct. Build. Mater., 93, 110-120. https://doi.org/10.1016/j.conbuildmat.2015.05.062.
  36. Mostofinejad, D. and Moghaddas, A. (2014), "Bond efficiency of EBR and EBROG methods in different flexural failure mechanisms of FRP strengthened RC beams", Construct. Build. Mater., 54, 605-614. https://doi.org/10.1016/j.conbuildmat.2014.01.002.
  37. Morsy, A.M., El-Tony, E.T.M. and El-Naggar, M. (2015), "Flexural repair/strengthening of pre-damaged RC beams using embedded CFRP rods", Alexandria Eng. J., 54(4), 1175-1179, https://doi.org/10.1016/j.aej.2015.07.012.
  38. Oh, H.-S. and Sim, J. (2004), "Interface debonding failure in beams strengthened with externally bonded GFRP", Compos. Interfaces. 11(1), 25-42. https://doi.org/10.1163/156855404322681037.
  39. Ozbakkaloglu, T. and Lim, J.C. (2013), "Axial compressive behavior of FRP-confined concrete: Experimental test database and a new design-oriented model", Compos. Part B: Eng., 55, 607-634. https://doi.org/10.1016/j.compositesb.2013.07.025.
  40. Ozbakkaloglu, T., Lim, J.C. and Vincent, T. (2013), "FRPconfined concrete in circular sections: Review and assessment of stress-strain models", Eng. Struct., 49, 1068-1088. https://doi.org/10.1016/j.engstruct.2012.06.010.
  41. Pham, H.B. and Al-Mahaidi, R. (2006), "Prediction models for debonding failure loads of carbon fiber reinforced polymer retrofitted reinforced concrete beams", J. Compos. Construct., 10(1), 48-59. https://doi.org/10.1061/(ASCE)1090-0268(2006)10:1(48).
  42. Rahimi, H. and Hutchinson, A. (2001), "Concrete beams strengthened with externally bonded FRP plates", J. Compos. Construct., 5(1), 44-56. https://doi.org/10.1061/(ASCE)1090-0268(2001)5:1(44).
  43. Raoof, M. and Hassanen, M. (2000), "Peeling failure of reinforced concrete beams with fibre-reinforced plastic or steel plates glued to their soffits", Proceedings of the institution of civil engineers-structures and buildings, 140(3), 291-305. https://doi.org/10.1680/stbu.2000.140.3.291.
  44. Ross, C.A, Jerome, D.M., Tedesco, J.W., and Hughes, M.L. (1999), "Strengthening of reinforced concrete beams with externally bonded composite laminates", Struct. J., 96(2), 212-220.
  45. Sabzi, J. and Esfahani, M. R, (2018) "Effects of tensile steel bars arrangement on concrete cover separation of RC beams strengthened by CFRP sheets", Construct. Build. Mater., 162, 470-479. https://doi.org/10.1016/j.conbuildmat.2017.12.053.
  46. Sabzi, J., Esfahani, M. Reza, Ozbakkaloglu, T. and Farahi, B. (2020), "Effect of concrete strength and longitudinal reinforcement arrangement on the performance of reinforced concrete beams strengthened using EBR and EBROG methods", Eng. Struct., 205, 110072. https://doi.org/10.1016/j.engstruct.2019.110072.
  47. Said, H. and Wu, Z. (2008), "Evaluating and proposing models of predicting IC debonding failure", J. Compos. Construct., 12(3), 284-299. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:3(284).
  48. Skuturna, T. and Valivonis, J. (2016), "Experimental study on the effect of anchorage systems on RC beams strengthened using FRP", Compos. Part B: Eng., 91, 283-290. https://doi.org/10.1016/j.compositesb.2016.02.001.
  49. Smith, S.T. and Teng, J. (2003), "Shear-bending interaction in debonding failures of FRP-plated RC beams", Adv. Struct. Eng., 6(3), 183-199. https://doi.org/10.1260/136943303322419214.
  50. Sobuz, H.R., Ahmed, E., Sutan, N.M., Hasan, N.M.S., Uddin, M.A. and Uddin, M.J. (2012), "Bending and time-dependent responses of RC beams strengthened with bonded carbon fiber composite laminates", Construct. Build. Mater., 29, 597-611. https://doi.org/10.1016/j.conbuildmat.2011.11.006.
  51. Spinella, N. (2019), "Modeling of shear behavior of reinforced concrete beams strengthened with FRP", Compos. Struct., 215, 351-364. https://doi.org/10.1016/j.compstruct.2019.02.073.
  52. Teng, J., Smith, S.T., Yao, J. and Chen, J.-F. (2003), "Intermediate crack-induced debonding in RC beams and slabs", Construct. Build. Mater., 17(6-7), 447-462. https://doi.org/10.1016/S0950-0618(03)00043-6.
  53. Teng, J. and Yao, J. (2007), "Plate end debonding in FRP-plated RC beams-II: Strength model", Eng. Struct., 29(10), 2472-2486. https://doi.org/10.1016/j.engstruct.2006.11.023.
  54. Uriayer, F.A. and Alam, M. (2015), "Steel-CFRP composite and their shear response as vertical stirrup in beams", Steel Compos. Struct., 18(5), 1145-1160. https://doi.org/10.12989/scs.2015.18.5.1145.
  55. Yao, J. and Teng, J. (2007), "Plate end debonding in FRP-plated RC beams-I: Experiments", Eng. Struct., 29(10), 2457-2471. https://doi.org/10.1016/j.engstruct.2006.11.022.
  56. Zhang, S.S. and Teng, J.G. (2014), "Finite element analysis of end cover separation in RC beams strengthened in flexure with FRP", Eng. Struct., 75, 550-560. https://doi.org/10.1016/j.engstruct.2014.06.031.