Ocean Systems Engineering

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Experimental and statistical investigation of torque coefficient in optimized surface piercing propeller

  • Masoud Zarezadeh (School of Mechanical Engineering, Iran University of Science and Technology) ;
  • Nowrouz Mohammad Nouri (School of Mechanical Engineering, Iran University of Science and Technology) ;
  • Reza Madoliat (School of Mechanical Engineering, Iran University of Science and Technology)
  • Received : 2023.12.12
  • Accepted : 2024.01.20
  • Published : 2024.03.25
⟨ Previous Next ⟩

Abstract

The interaction of the blade of surface-piercing propellers (SPPs) with the water/air surface is a physical phenomenon that is difficult to model mathematically, so that such propellers are usually designed using empirical approaches. In this paper, a newly developed mechanism for measuring the torque of SPPs in an open water circuit is presented. The mechanism includes a single-component load cell and a deformable torque sensor to detect the forces exerted on the propeller. Deformations in the sensor elements lead to changes in the strain gauge resistance, which are converted into voltage using a Wheatstone bridge. The amplified signal is then recorded by a 16-channel data recording system. The mechanism is calibrated using a 6-DoF calibration system and a Box-Behnken design, achieving 99% accuracy through multivariate regression and ANOVA. Finally, the results of performance tests on a 4-blade propeller were presented in the form of changes in the torque coefficient as a function of feed rate. The results show that the new mechanism is 8% more accurate than conventional empirical methods.

Keywords

Acknowledgement

We are grateful to the Hydrotech Group, which operates in the field of scientific technologies.

References

  1. Amini, A., Nouri, N.M., Abedi, A. and Kamran, M. (2021), "Performance improvement of surface piercing propeller at low advance coefficients by aeration", Ocean Eng., 238, 109551. https://doi.org/10.1016/j.oceaneng.2021.109551.
  2. Bahaj, A., Molland, A., Chaplin, J. and Batten, W. (2007), "Power and thrust measurements of marine current turbines under various hydrodynamic flow conditions in a cavitation tunnel and a towing tank", Renew. Energ., 32(3), 407-426. https://doi.org/10.1016/j.renene.2006.01.012.
  3. Bartz, J.R. and Blatz, J.A. (2022), "Considerations for measuring residual stresses in driven piles with vibrating wire strain gauges", Can. Geotech. J., 59(3), 441-446. https://doi.org/10.1139/cgj-2020-0614.
  4. Bose, N., Dugue, C., Esposito, P.G., Holtrop, J., Jessup, S., Lee, J.T., Mewis, F., Poustoshny, A., Salvatore, F. and Shirose, Y. "The Propulsion Committee".
  5. Brookshire, K. (2022), An Analysis on Hydrodynamic Loads for Surface-Piercing Propellers Using Computational Fluid Dynamics, Virginia Tech.
  6. Carlton, J. (2018), Marine propellers and propulsion, Butterworth-Heinemann.
  7. Chen, X., Huang, Y., Wei, P., Zhang, Z. and Jin, F. (2018), "Numerical analysis of scale effect on propeller E1619", International Conference on Offshore Mechanics and Arctic Engineering, https://doi.org/10.1115/OMAE2018-78213.
  8. Ding, E. (2007), "A series of surface piercing propellers and its application", Proceedings of the 9th International Conference on Fats Sea Transportation, Shanghai, China.
  9. Dyson, P.K. (2000), "Modelling, testing and design, of a surface piercing propeller drive".
  10. Eskandari, M. and Ghassemi, H. (2022), "A simple practical method to show the forces of the surface propeller during one cycle", Am. J. Mech. Eng., 10(1), 34-40.
  11. Ferrando, M., Crotti, S. and Viviani, M. (2007). "Performance of a family of surface piercing propellers", Proceedings of the 2nd International Conference on Marine Research and Transportation (ICMRT), Ischia.
  12. Ferrando, M. and Scamardella, A. (1996), "Surface piercing propellers: Testing methodologies, results analysis and comments on open water characteristics".
  13. Funeno, I., Pouw, C. and Bosman, R. (2013). "Measurements and computations for blade spindle torque of controllable pitch propellers in open water", Proceedings of the 3rd International Symposium on Marine Propulsors smp.
  14. Ha, J., Park, J., Park, G., Kim, J., Kim, J., Seo, J. and Rhee, S.H. (2023), "Experimental study on the propulsion performance of a partially submerged propeller", Int. J. Naval Architect. Ocean Eng., 15, 100516. https://doi.org/10.1016/j.ijnaoe.2023.100516.
  15. Hecker, R. and Crown, D. (1970), "Performance characteristics of partially-submerged propeller 4281 with varying number of blades at low advance coefficients", NSRDC T and E Report.
  16. Kamran, M., Nouri, N.M., Goudarzi, H. and Golrokhifar, S. (2022), "Experimental evaluation of the effect of positioning and operating parameters on the performance of a surface-piercing propeller", Scientific Reports. 12(1), 18566. https://doi.org/10.1038/s41598-022-21959-x.
  17. Kikuchi, H., Sasaki, N., MURAKAMI, K., KIHARA, H., YABUSHITA, K. and SUZUKI, K. (1999), "Experimental study on surface piercing propeller with axis horizontally raked", J. Kansai Soc. Naval Archit. Jpn., 1-8.
  18. Kruppa, C. (1975), "Propulsion devices for high-speed craft (Testing techniques)", Proceedings of the 14th international towing tank conference (Report of cavitation committee), Ottawa, ON, Canada.
  19. Liu, S. and Zhu, H. (1988), "An experimental study on the performance characteristics of partially submerged propeller", Proceedings of the International High Performance Vehicle Conference.
  20. Lorio, J.M. (2010), Open water testing of a surface piercing propeller with varying submergence, yaw angle and inclination angle, Florida Atlantic University
  21. Lumley, J.L. and McMahon, J. (1967), "Reducing water tunnel turbulence by means of a honeycomb".
  22. Mehta, R.D. and Bradshaw, P. (1979), "Design rules for small low speed wind tunnels", Aeronaut. J., 83(827), 443-453.
  23. Nozawa, K. and Takayama, N. (2002), "Experimental study on propulsive performance of surface piercing propeller", J. Kansai Soc. Naval Archit. Jpn., 63-70.
  24. Olofsson, N. (1996), "Force and ow characteristics of a partially submerged propeller doctoral thesis", Goteborg: Chalmers University of Technology {Department of Naval Architecture and Ocean Engineering.
  25. Peterson, D.T. (2005), Surface piercing propeller performance, Citeseer
  26. Pustoshny, A. and Rusetsky, A. (2006), "Naval and commercial fast ship development experience and further prospects", Aust. J. Mech. Eng., 3(2), 79-90. https://doi.org/10.1080/14484846.2006.11464497.
  27. Seyyedi, S.M., Shafaghat, R. and Siavoshian, M. (2019), "Experimental study of immersion ratio and shaft inclination angle in the performance of a surface-piercing propeller", Mech. Sci., 10(1), 153-167. https://doi.org/10.5194/ms-10-153-2019.
  28. Shafaghat, R. (2016), "Design algorithm of a free surface water tunnel to test the Surface-Piercing Propellers (SPP); Case study water tunnel of Babol Noshirvani university of technology", Int. J. Maritime Tech., 6, 19-30. https://doi.org/10.18869/acadpub.ijmt.6.19.