Geomechanics and Engineering

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Assessing the influence of displacement rates on the failure behavior and undrained shear strength characteristics of reconstituted varve laminae prepared at different moisture contents

  • Deepali Anand (Department of Civil Engineering, Indian Institute of Technology Guwahati) ;
  • Arindam Dey (Department of Civil Engineering, Indian Institute of Technology Guwahati) ;
  • K. Ravi (Department of Civil Engineering, Indian Institute of Technology Guwahati)
  • Received : 2024.11.19
  • Accepted : 2025.09.24
  • Published : 2025.10.25
⟨ Previous Next ⟩

Abstract

The geotechnical behavior of varved clays in cold regions remains inadequately understood despite their widespread occurrence. This study addresses this gap by investigating the behavior of homogeneous and reconstituted varved clay samples through Unconfined Compressive Strength (UCS) testing. Homogeneous samples consist of Red Soil (RS) and Black Soil (BS), while reconstituted varved clays are prepared by layering RS and BS in configurations of 2, 4, 8, and 16 layers. UCS tests are conducted at displacement rates of 1.25, 0.24, and 0.024 mm/min, hypothesized to simulate the velocity of glacial override on soils. Samples are prepared at five moisture contents ranging from 0.8 to 1.2 OMC. Results indicate that as moisture content decreases below OMC, undrained shear strength increases for all samples, accompanied by a reduction in strain, while the opposite trend is observed for samples on the wet side of OMC. For reconstituted varved clays, undrained shear strength increases as number of laminae rises from 2 to 8, but decreases in the 16-laminae sample, which suggests a threshold exists for the number of laminae beyond which strength reduces. Displacement rate significantly influences failure modes and patterns, with samples exhibiting more ductile behavior at lower displacement rates and higher moisture contents.

Keywords

Acknowledgement

This study belongs to a part of the project 'Study of Glacial Dynamics and Sustainable Hydrological Resources in Arunachal Himalaya' (Project No. DST/CCP/MRDP/185/2019(G) dated 13/03/2020). The project is supported by Department of Science & Technology (SPLICE - Climate Change Program), Ministry of Science and Technology, Govt. of India. The authors express their gratitude for receiving the financial support for the same.

References

  1. Ali, M., Aziz, M., Hamza, M. and Madni, M.F. (2020), "Engineering properties of expansive soil treated with polypropylene fibers", Geomech. Eng., 22(3), 227-236. https://doi.org/10.12989/gae.2020.22.3.227.
  2. ASTM D3080/D3080M (2011), Standard test method for direct shear test of soils under consolidated drained conditions, American Standard Testing Methods; West Conshohocken, PA: ASTM.
  3. Awoleye, O.A., Bouazza, A. and Rama-Rao, R. (1991), "Time effects on the unconfined compressive strength and sensitivity of a clay", Eng. Geol., 31(3-4), 345-351. https://doi.org/10.1016/0013-7952(1)90016-E.
  4. Balagosa, J.A., Lee, M.J., Choo, Y.W., Kim, H.S. and Kim, J.M. (2024), "Effect of wood pellet fly ash on strength and microstructure of Korean weathered granite soil", Geomech. Eng., 38(4), 335-352. https://doi.org/10.12989/gae.2024.38.4.335.
  5. Blondeau, K.M. (1975), "Sedimentation and stratigraphy of the Mount Rogers Formation, Virginia", MS Dissertation; Louisiana State University and Agricultural and Mechanical College. https://doi.org/10.31390/gradschool_disstheses.8236.
  6. Chompoorat, T., Likitlersuang, S., Sitthiawiruth, S., Komolvilas, V., Jamsawang, P. and Jongpradist, P. (2021), "Mechanical properties and microstructures of stabilised dredged expansive soil from coal mine", Geomech. Eng., 25(2), 143-157. https://doi.org/10.12989/gae.2021.25.2.143.
  7. Chhun, K.T., Choo, H., Kaothon, P. and Yune, C.Y. (2020), "Experimental study on the strength behavior of cement-stabilized sand with recovered carbon black", Geomech. Eng., 23(1), 31-38. https://doi.org/10.12989/gae.2020.23.1.031.
  8. Dobak, P., Kiełbasiński, K., Szczepański, T. and Zawrzykraj, P. (2018), "Verification of compressibility and consolidation parameters of varved clays from Radzymin (Central Poland) based on direct observations of settlements of road embankment", Open Geosci., 10(1), 911-924. https://doi.org/10.1515/geo-2018-0072.
  9. Du, H., Ma, W., Zhang, S., Zhou, Z. and Liu, E. (2016), "Strength properties of ice-rich frozen silty sands under uniaxial compression for a wide range of strain rates and moisture contents", Cold Reg. Sci. Technol., 123, 107-113. https://doi.org/10.1016/j.coldregions.2015.11.017.
  10. Eden, W.J. (1955), "A laboratory study of varved clay from Steep Rock Lake, Ontario", Report No. DBR-R-24, National Research Council of Canada - Division of Building Research. https://doi.org/10.4224/20331506
  11. Ehlers, J. (2022), "From Moulins to Glacial Valleys", In: The Ice Age. Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-662-64590-1_5.
  12. Eigenbrod, K.D. and Burak, J.B. (1991), "Effective stress paths and pore-pressure responses during undrained shear along the bedding planes of varved Fort William Clay", Can. Geotech. J., 28(6), 804-811. https://doi.org/10.1139/t91-097.
  13. Fard, A.R., Moradi, G., Ghalehjough, B.K. and Abbasnejad, A. (2020), "Freezing-thawing resistance evaluation of sandy soil, improved by polyvinyl acetate and ethylene glycol monobutyl ether mixture", Geomech. Eng., 23(2), 179-187. https://doi.org/10.12989/gae.2020.23.2.179.
  14. Flieger-Szymanska, M., Machowiak, K., Krawczyk, D. and Wanatowski, D. (2019), "Characterisation of mineral composition and strength parameters of varved clays", Proceedings of the 17th European Conference on Soil Mechanics and Geotechnical Engineering (ECSMGE 2019), Reykjavik, Iceland. http://doi.org/10.32075/17ECSMGE-2019-0172.
  15. Florkiewicz, A., Flieger-Szymanska, M., Machowiak, K. and Wanatowski, D. (2014), "Engineering properties of varved clays from the Junikowski Stream Valley in Poland", Proceedings of the 4th International Conference on Geotechnical Engineering for Disaster Mitigation and Rehabilitation (4th GEDMAR), Kyoto, Japan.
  16. Girgis, N., Li, B., Akhtar, S. and Courcelles, B. (2020), "Experimental study of rate-dependent uniaxial compressive behaviors of two artificial frozen sandy clay soils", Cold . Sci. Technol., 180, 103166, 1-13. https://doi.org/10.1016/j.coldregions.2020.103166.
  17. Gruchot, A. and Zydroń, T. (2024), "Effect of shear rate and saturation on shear strength of mineral and anthropogenic soil", Archiv. Civil Eng., 70(2), 97-117. http://doi.org/10.24425/ace.2024.149853.
  18. Hampton, D. and Yoder, E.J. (1958), "The effect of rate of strain on soil strength", Joint Highway Research Project No. C-36-20B, Purdue University, Lafayette, Indiana, 116- 129.
  19. Hang, T. (2003), "A local clay-varve chronology and proglacial sedimentary environment in glacial Lake Peipsi, Eastern Estonia", Boreas, 32(2), 416-426. https://doi.org/10.1111/j.1502-3885.2003.tb01094.x.
  20. Ibdah, L., Owusu, K., Behdad, A. and Eun, J. (2024), "Effects of freeze-thaw cycles on the unconfined compressive strength of lime- and cement-stabilized soils", Geomech. Eng., 41(1), 59-70. https://doi.org/10.12989/gae.2025.41.1.059.
  21. IS 2720 Part 3/Sec-2 (1980), Methods of test for soils: Determination of specific gravity: Fine, medium, and coarse-grained soils, Bureau of Indian Standards; New Delhi, India.
  22. IS 2720 Part 4 (1980), Methods of test for soils: Grain size analysis, Bureau of Indian Standards; New Delhi, India.
  23. IS 2720 Part 5 (1985), Methods of test for soils: Determination of liquid limit and plastic limit, Bureau of Indian Standards, New Delhi, India.
  24. IS 2720 Part 7 (1983), Methods of test for soils: Determination of water content-dry density relation using light compaction, Bureau of Indian Standards, New Delhi, India.
  25. Jin, H., Lee, J., Zhuang, L. and Ryu, B.H. (2020), "Laboratory investigation of unconfined compression behavior of ice and frozen soil mixtures", Geomech. Eng., 22(3), 219-226. https://doi.org/10.12989/gae.2020.22.3.219.
  26. Jummasultan, A., Sagidullina, N., Kim, J., Ku, T. and Moon, S.W. (2021), "Performance of cement-stabilized sand subjected to freeze-thaw cycles", Geomech. Eng., 25(1), 41-48. https://doi.org/10.12989/gae.2021.25.1.041.
  27. Kazi, A. (1967), "Aspects of the engineering geology of laminated glacial lake clays", Ph.D. Dissertation, Imperial College of Science, London.
  28. Krawczyk, D. and Flieger-Szymańska, M. (2018), "The value of plasticity index (IP) and liquidity index (IL) of North Polish ablation boulder clays and varved clays depending of the method of its determination", Scientific Rev. Eng. Environ. Sci., 27(2), 167-174. http://doi.org/10.22630/PNIKS.2018.27.2.16.
  29. Lacasse, S.M., Ladd, C.C. and Barsvary, A.K. (1977), "Undrained behavior of embankments on New Liskeard varved clay", Can. Geotech. J., 14(3), 367-388. https://doi.org/10.1139/t77-041.
  30. Lamoureux, S.F. and Bradley, R.S. (1996), "A late Holocene varved sediment record of environmental change from northern Ellesmere Island, Canada", J. Paleolimnol., 16, 239–255. https://doi.org/10.1007/BF00176939.
  31. Leroueil, S., Bouclin, G., Tavenas, F., Bergeron, L. and Rochelle, P.L. (1990), "Permeability anisotropy of natural clays as a function of strain", Can. Geotech. J., 27(5), 568-579. https://doi.org/10.1139/t90-072.
  32. Lindqvist, J.K. and Lee, D.E. (2009), "High-frequency paleoclimate signals from Foulden Maar, Waipiata Volcanic Field, southern New Zealand: An Early Miocene varved lacustrine diatomite deposit", Sediment. Geol., 222(1-2), 98-110. https://doi.org/10.1016/j.sedgeo.2009.07.009.
  33. Liu, S., Liao, C., Chen, J., Ye, G. and Xia, X. (2024), "Shear rate effect on clay-structure interface strength properties in various interface boundary conditions", Soil Dyn. Earthq. Eng., 177, 1-14. https://doi.org/10.1016/j.soildyn.2023.108389.
  34. Lo, K.Y. and Milligan, V. (1967), "Shear strength properties of two stratified clays", J. Soil Mech. Found. Div. ASCE, 93(1). https://doi.org/10.1061/JSFEAQ.0000928.
  35. Luo, L., Yang, Y., Shen, Z., Zhang, W., Wang, Z., Wang, X., Gao, H. and Xu, Q. (2025), "Experimental study on the mechanical behavior of artificially prepared stratified soil in triaxial compression tests", Acta Geotechnica, 20, 543-562. https://doi.org/10.1007/s11440-024-02426-5.
  36. Lydzba D. and Tankiewicz M. (2012), study of failure anisotropy characterization ofvarved clay',AGHJ. Min. Geoeng,36(2), 229-234.
  37. Martinez, A. and Stutz, H.H. (2019), "Rate effects on the interface shear behaviour of normally and overconsolidated clay", Géotechnique, 69(9), 801-815. https://doi.org/10.1680/jgeot.17.P.311.
  38. Mousavi, F., Abdi, E., Ghalandarayeshi, S. and Page-Dumroese, D.S. (2021), "Modeling unconfined compressive strength of fine-grained soils: Application of pocket penetrometer for predicting soil strength", CATENA, 196, 1-7. https://doi.org/10.1016/j.catena.2020.104890.
  39. Mukherjee, M. and Pathak, S. (2023), "Rate-dependent shearing response of Toyoura sand addressing influence of initial density and confinement: A visco-plastic constitutive approach", Geomech. Eng., 34(2), 197-208. http://doi.org/10.12989/gae.2023.34.2.197.
  40. Philippe, E.G.H., St-Onge G., Valet J.P., Godbout P.M., Egli R., Francus P. and Roy M. (2023), "Influence of seasonal postdepositional processes on the remanent magnetization in varved sediments from glacial lake Ojibway (Canada)", Geochem. Geophys. Geosyst., 24(3), 1-20. https://doi.org/10.1029/2022GC010707.
  41. Ramesh, H.N., Kulkarni, M.G.R., Raghunandan, M.V. and Nethravathi, S. (2022), "Mechanical and microstructural investigations on cement-treated expansive organic subgrade soil", Geomech. Eng., 38(4), 353-366. https://doi.org/10.12989/gae.2024.38.4.353.
  42. Ringberg, B. and Erlström, M. (1999), "Micromorphology and petrography of Late Weichselian glaciolacustrine varves in southeastern Sweden", Catena, 35(2-4), 147-177. https://doi.org/10.1016/S0341-8162(98)00098-8.
  43. Sabatini, P.J., Bachus, R.C., Mayne, P.W., Schneider, J.A. and Zettler, T.E. (2002), "Evaluation of soil and rock properties", Geotechnical Engineering Circular No. 5, Technical Manual. https://rosap.ntl.bts.gov/view/dot/40554.
  44. Safa, M., Maleka, A., Arjomand, M.A., Khorami, M. and Shariati, M. (2019), "Strain rate effects on soil-geosynthetic interaction in fine-grained soil", Geomech. Eng., 19(6), 533–542. http://doi.org/10.12989/GAE.2019.19.6.533
  45. Sagidullina, N., Kim., J., Satyanaga, A., Ku, T. and Moon, S.W. (2024), "Mechanical and microstructural investigations on cement-treated expansive organic subgrade soil", Geomech. Eng., 38(4), 353-366. https://doi.org/10.12989/gae.2024.38.4.353.
  46. Sahlabadi, S.H., Bayat, M., Mousivand, M. and Saadat, M. (2021), "Freeze–thaw durability of cement-stabilized soil reinforced with polypropylene/Basalt fibers", J. Mater. in Civil Eng., 33(9), 04021232. http://doi.org/10.1061/(ASCE).
  47. Schneider, M.A., Whittle, R.W. and Springman, S.M. (2022), "Measuring strength and consolidation properties in lacustrine clay using piezocone and self-boring pressuremeter tests", Can. Geotech. J., 59(12), 2135-2150. https://doi.org/10.1139/cgj-2021-0486.
  48. Tankiewicz, M. (2015), "Experimental investigation of strength anisotropy of varved clay", Procedia Earth and Planetary Sci., 15, 732-737. https://doi.org/10.1016/j.proeps.2015.08.116.
  49. Tankiewicz, M. (2016), "Structure investigations of layered soil – varved clay", Annals of Warsaw University of Life Sciences SGGW Land Reclamation, 48(4), 365-375. http://doi.org/10.1515/sggw-2016-0028.
  50. Tornborg, J., Karlsson, M. and Karstunen, M. (2023), "Permanent sheet pile wall in soft sensitive clay", J. Geotech. Geoenviron. Eng. - ASCE, 149(6). https://doi.org/10.1061/JGGEFK.GTENG-10955.
  51. Tyagi, A., Wong, Y.C.D. and Lee, F.H. (2019), "Effect of loading strain-rates on peak strength and drainage behaviour of cement-treated soils", Proceedings of the 16th Asian Regional Conference on Soil Mechanics and Geotechnical Engineering.
  52. Wang, Y. and Cong, L. (2019), "Effects of water content and shearing rate on residual shear stress", Arabian J. Geosci., 44, 8915-8929. https://doi.org/10.1007/s13369-019-03922-7.
  53. Wang, C.C., Lin, H.D., Li, A.J. and Ting, K.E. (2020), "Assessment of the unconfined compression strength of unsaturated lateritic soil using the UPV", Geomech. Eng., 23(4), 339-349. https://doi.org/10.12989/gae.2020.23.4.339.
  54. Zarei, C., Soltani-Jigheh, H. and Liu, Y. (2023), "Effects of strain rate and specimen size on the behavior of fine-grained soils", Arabian J. Geosci., 16, 244. https://doi.org/10.1007/s12517-023-11344-x
  55. Zhang, C., Li, D., Luo, C., Wang, Z. and Chen, G. (2022), "Research on creep characteristics and the model of artificial frozen soil", Adv. Mater. Sci. Eng., 1, 1-15. https://doi.org/10.1155/2022/2891673.