In this study a measurement equipment was designed and made for the nonlinear dielectric constants in dielectrics. The determining method of the nonlinear dielectric constants also was proposed. The measurement equipment was consisted of the wave generation part, the high voltage amplifier part, the measurement part and the data acquisition part. In this equipment the measurement control and the data processing could be conducted by computer. In order to determine the nonlinear dielectric constants alternating sign-wave electric fields are applied to dielectrics with different magnitude and the waves of the electric fields and the response from dielectrics are stored in computer memories. The harmonics of dielectric displacement are obtained by the Fourier transformation of these waves. The nonlinear dielectric constants are determined at the relatively low-field region. The experiment for PZT ceramic samples was done by the equipment and the determining method and as the result meaningful data were obtained.

In this study, laser ablation atomic fluorescence (LAAF) spectroscopy has been applied for a nanometer-scale surface analysis of Na-doped polymethyl methacrylate (PMMA). LAAF spectroscopy is a new sensitive element detection technique which involves atomizing of a sample by the laser ablation and detection of ablated plume by laser-induced fluorescence (LIF) spectroscopy. Using this technique in the detection of Na atoms with Na-doped PMMA, a detection limit is obtained as 36 fg for single laser shot. Further, the depth distribution in the sample is measured with a very high spatial resolution using a two-layer PMMA sample by observing the shot-by-shot LIF intensity from the Na atoms.

We have investigated the relation between the molecular weight distribution (MWD) of diffusible species and the recovery rate of hydrophobicity of room-temperature vulcanizing (RTV) silicone rubber (SIR) using solvent extraction at various temperatures. It was observed that the extract had a MWD ranging from a few hundreds g/mol to hundreds of thousands g/mol. By measuring the migration of siloxane to the extracted SIR surface through a thin carbon coating, the aspect of migration of diffusible species was observed as a real time plot, and the time constant of the migration was also calculated. According to the time dependence of IR-absorbance, the time constant was increased with the increase of MW of the extracts.

ZnO thin films are Prepared on Si(111) substrate by RF magnetron sputtering. Two-step deposition method is proposed to obtain ZnO thin films with high c-axis (002) TC value and electrical resistivity. This method consists of the following two-step deposition procedures: 1st-deposition for 10$\sim$30 min without oxygen at 100W and 2nd-deposition with oxygen added in the range of $O_2/(Ar+O_2)$ = 10 $\sim$ 50%. SAW filters with IDT/ZnO/Si(111) configuration are also fabricated. From the frequency response characteristics, the insertion loss and the side-lobe rejection are estimated.

본 논문은 스냅백을 효과적으로 제거하고 순방향 전압 강하를 줄이는 새로운 구조의 분리된 이중 게이트 SOI SA-LIGBT를 제안하였다. 제안된 소자는 분리된 단락 애노드와 플로팅 오믹 접합의 적용을 통해 스냅백이 성공적으로 제거되었고, 순방향전압강하는 전류밀도가 100A/$cm^2$일 때 기존의 SA-LIGBT에 비교해서 2V 감소된다. 또한 턴-오프 특성도 분리된 단락 애노드를 적용하였기 때문에 SA-LIGBT보다 개선되었다.

Generally, Invar alloy shows very low thermal expansion characteristics, lower than $2{\times}10^{-6}$/K approximately. To apply Fe-Ni-Co-C Invar alloy as a core material for large ampacity transmission line we studied the effects of magnetic properties on coefficient of thermal expansion. The coefficient of thermal expansion(CTE) suddenly decreases with addition of a little carbon(0.08%), increases with the increasing carbon and has a constant value at the composition over than 1.0%C. The trend of Curie temperature change with carbon is similar with that of CTE. Therefore, the CTE has a linear relationship with Curie temperature. However, the CTE linearly decreases with the ratio of saturation magnetization and Curie temperature(${\sigma}_s/T_c$).

Polycrystalline diamond films are deposited by using a microwave plama CVC system, where the bias-enhanced nucleation (BEN) method is employed. Effects of the varying microwave power, the surface treatment by hydrogen plasma, and the cyclic hydrogen etching during deposition on the crystallinity as well as on the surface roughness of deposited films are examined by Raman spectroscopy, SEM, and AFM. A novel method for achieving a smoother diamond surface is also suggested through the indirect wafer bonding and back-side polishing.

후막 EL소자는 연속동작 중에 발광특성이 저하되는 특징을 가진다. 본 연구는 상온과 $70^{\circ}C$, 상대 습도 100% 환경에서 후막 EL소자를 100V, 400Hz의 전원을 인가한 후 휘도 변화를 측정 및 비교하였다. 또한 열화된 시료의 표면 및 측면 주사 전자 현미경 사진을 통해 열화 부분을 관찰하였다. 측정된 휘도와 열화 메카니즘을 통해 sulfur vacancy와 deep traps 농도 시뮬레이션을 활용하였다. 후막 EL소자의 발광 특성은 주변의 온도 및 습도에 의해 크게 저하됨을 확인하였다.

An experimental study on arc resistance and light reflectance of PTFE is presented. PTFE has been used widely as a material for circuit breaker nozzle. In the arcing environment, radiative power incident upon the nozzle wall may be transmitted through the nozzle material. Adding some fillers into PTFE was expected to be efficient in improving the endurability to radiation.

0.2${\mu}m$ 이하의 최소 선폭을 가지는 소자를 구현할 때 drain induced barrier lowering (DIBL)이나 hot electron effect와 같은 short channel effect (SCE)가 나타나며 이로 인하여 소자의 신뢰성이 악화되기도 한다. 이를 개선하기 위한 방법 중 하나가 silicon selective epitaxial growth (SEG)를 이용한 elevated source/drain (ESD) 구조이다. 본 연 구에서는 silicon selective epitaxial growth를 이용하여 elevated source/drain 구조를 갖는 MOSFET 소자와 일반적인 MOSFET 구조를 갖는 소자와의 차이를 elevated source/drain의 높이 변화에 따른 전류 전압 특성을 이용하여 비교, 분석하였으며 그 결과 elevated source/drain 구조가 short channel effect를 감소시킴을 확인할 수 있었다.

본 논문에서는 다이어프램을 세라믹을 사용하여 2차 변환 소자로 금속 스트레인 게이지 대신에 thick film piezoresistor를 이용한 후막 압력센서에 관한 연구이다. 다이어프램의 미소 변형을 후막의 비저항 변화로 검출하는 압저항 효과를 이용하는 방식이다. 종래의 압력센서와 비교하여 크리프 현상이 적고, 안정성이 우수한 특징을 갖고 있다. 또한 저항선이나 박 게이지의 게이지율이 3$\sim$5 인 것이 비하면 후막저항을 사용한 경우, 약 15$\sim$20정도의 높은 게이지율을 얻을 수 있어서 측정범위를 넓게 할 수 있으며, 후막공정의 스크린 프린팅을 통한 자동화는 수율의 향상과 저 가격화를 실현할 수 있다. 또, 후막 저항형 압력센서는 두 개의 저항이 다이어프램의 중앙 부근에 위치하며, 나머지 두 개의 저항은 가장자리에 위치시킴으로써 미소 변형에서도 저항값의 변화를 읽을 수 있도록 하였고, 휘스톤 브리지의 연결 도체부는 Pt를 주성분으로 하는 conductive paste(DHC7085)를 사용하였다. 이렇게 설계.제작된 압력 센서를 지지대에 고정시킨 후 캡슐에 넣고 감도, 선형성, 히스테리시스 그리고 온도특성 등을 고찰하였다.

다공질 실리콘(PSi)의 형성방법중에 가장 주된 방식인 전기화학법은 매우 범용화된 기술이다. 이러한 전기화학법을 이용한 PSi 제작방식에 있어 HF 가 함유된 전해액과 첨가되는 첨가제는 PSi 형성에 매우 중요한 역할을 한다. 전해액에 첨가되어지는 첨가재는 종류에 따라 전해질과 기판사이의 친수성 및 전해액의 표면장력을 작게 하는 역할을 하며, 그 밖의 기판 표면 상태변화의 원인으로서 양극산화 공정에 많은 변수로 작용한다. 본 논문에서는 기존의 에틸알콜을 함유한 HF 전해액과 새로운 용매를 함유한 HF 전해액에 대한 PSi의 형성을 광학 현미경 사진과 시간에 따른 전류 및 전압 특성 곡선으로 비교 분석하였으며, 기존 식각 용액을 사용했을 경우의 표면 식각현상과 형성구조의 불균일성 등을 해결할 수 있었다.

In this study it can be confirmed that the formula by the free-rotational dipole theory is similiar with that by the phenomenological theory and the non-linear permittivity is determined only with the third harmonic conponent of polarization. Various parameters of VDCN copolymers were obtained from fitting results with the related formula.

This paper describes on thinning SDB SOI substrates by SDB technology and Electro-chemical etch-stop. The surface of the fabricated SDB SOI substrates is more uniform than that grinding or polishing by mechanical method, and this process is possible to accurate SOI thickness control. During Electrochemical etch-stop, leakage current versus voltage curves were measured for analysis of the open current potential (OCP) point and the passivation potential (PP) poin and determinated to anodic passivation potential. The surface roughness and selectively controlled thickness of the fabricated SOI substrates were analyzed by using AFM and SEM, respectively.

This paper describes fabrication and characteristics of metal thin-film pressure sensor for working at high temperature. The proposed pressure sensor consists of a chrom thin-film, patterned on a Wheatstone bridge configuration, sputter-deposited onto thermally oxidized Si membranes with an aluminium interconnection layer. The fabricated pressure sensor presents a low temperature coefficient of resistance, high-sensitivity, low non-linearity and excellent temperature stability. The sensitivity is 1.097 $\sim$ 1.21 mV/V kgf/$cm^2$ in the temperature range of 25 $\sim$ $200^{\circ}C$ and the maximum non-linearity is 0.43 %FS.

This paper describes the fabrication and characteristics of CrN thin-film type pessure sensors, in which the sensing elements were deposited on SUS. 630 diaphragm by DC reactive magnetron sputtering in an argon-nitride atmosphere(Ar-(10%) $N_2$). The optimized condition of CrN thin-film sensing elements was thickness range of 3500$\AA$ and annealing condition($300^{\circ}C$, 3 hr) in Ar-10 %$N_2$ deposition atmosphere. Under optimum conditions, the CrN thin-films for strain gauges is obtained a high resistivity, $\rho$=1147.65 ${\mu}{\Omega}$cm, a low temperature coefficient of resistance, TCR=-186 ppm/$^{\circ}C$ and a high temporal stability with a good longitudinal, 11.17. The output sensitivity of fabricated CrN thin-film type pressure sensors is 2.36 mV/V, 4$\sim$20 mA and the maximum non-linearity is 0.4 %FS and hysteresis is less than 0.2 %FS..

Ohmic contacts have been fabricated on p-type 4H-SiC using Pt/Ti. Low resistivitf Ohmic contacts of Pt/Ti to p-type 4H-SiC were investigated. Specific contact resistances were measured using the transmission line model method, and the physical properties of the contacts were examined using x-ray diffraction, scanning electron microscopy. Ohmic behavior with linear current-voltage characteristics was observed following anneals at $900^{\circ}C$ for 90sec at a pressure of $3.4{\times}10^{-5}$ Torr. The Pt/Si/Ti films was measured lower value of the specific contact resistance by the annealing process, and the contact resistances were improved more than one order compared to Ti contact the annealed sample. Scanning electron microscopy shows that the Pt layer effectively reduce the oxidation of Ti films. And results are obtained as $4.6{\times}10^{-4}$ ohm/$cm^2$ for a Pt/Ti metal structure after a vacuum annealing at $900^{\circ}C$ for 90sec. Titanium has a relatively high melting point, thus Ti-based metal contacts were attempted in this study.

원자력 발전소의 격납 건물에 설치된 안전 관련 케이블은 고온, 고 방사선의 열악한 환경으로 인해 열화 될 수 있다. 원자력발전소에 설치된 케이블 중 특히 발전소의 안전에 중요한 케이블은 안전관련기기의 동작에 필요한 전원을 공급하는 중요한 역할을 하고 있다. 원자력발전소의 수명 40년 혹은 수명연장을 고려하면 격납 건물에 설치된 안전관련 케이블의 상태를 확인할 필요가 있다. 지금까지 사용되고 있는 케이블의 상태 감시 방법에는 케이블의 물리적 성질, 전기적 성질 및 화학적 성질을 이용한 여러 가지방법이 제시되어 있다. 그러나 원자력 발전소에서 케이블의 상태 감시를 하기 위해서는 원자력 발전소의 열악한 환경과 운전 특수성을 고려하여야 한다. 본 논문에서는 원자력 발전소의 이러한 환경과 운전특성, 그리고 현재까지 제시된 케이블의 각 상태감시 방법의 장, 단점을 분석하여 원자력 발전소 현장과 안전성에 가장 적합한 상태감시 방법을 제시하였다.

In this paper, the structural and electrical properties of the $Sr_{1-x}Ca_xTiO_3$($0{\leq}x{\leq}0.2$)-based grain boundary layer ceramics were investigated by X-ray, SEM and V-I system. Increasing content of Ca, the average gram size and the lattice constant were decreased. The relative density of all specimens was > 96%. The 2nd phase formed by thermal diffusing from the surface lead to a very excellent electrical properties, that is, ${\varepsilon}_r$ > 50000, tan${\delta}$ < 0.05, $\Delta$C < ${\pm}$ 10%.

In this paper, the microstructure and the dielectric properties of the $Sr_{1-x}Ca_xTiO_3$($0{\leq}x{\leq}0.2$)-based grain boundary layer ceramics were investigated. The 2nd phase formed by thermal diffusing from the surface lead to a very high apparent dielectric constant, ${\varepsilon}_r$ > 50000, and tan$\delta$ < 0.05, $\Delta$C < ${\pm}$ 10%.

ZnO-based SAW(surface acoustic wave) filters are fabricated with the configuration of IDT/ZnO/$SiO_2$/Si(100) using various IDT materials such as Al, Cu/Ti, and Cu/Al. Their frequency response characteristics are measured and compared. The thickness of Al IDT is varied to examine the mass loading effect. In addition, effects of thermal treatment and electrical stress on the frequency responses of the fabricated SAW filters are investigated.

DLC films are deposited by using a modified FCVA system. Carbon amorphous network, surface roughness, internal compressive stress, resistivity, and Hall mobility are studied as a function of nitrogen flow rate (0 $\sim$ 10 sccm). As the nitrogen content is increased in the carbon network, the size of $sp^2$ clusters is increased, the internal compressive stress is decreased, and the resistivity is remarkably decreased. The RMS values of the surface roughness are measured to be in the range of 0.2$\sim$0.5nm. The Hall mobility of DLC film with 3 sccm of nitrogen added is 3.22 $cm^2/V{\cdot}$s.

The $HoSi_2$ compounds prepared by codeposition of Si and Ho, and $HoSi_2$ by sintering method were investigated electrical and Hall effect. The crystal structure of samples showed a orthorhombic structure, and lattices constant is a=9.8545 $\AA$, b=7.7935 $\AA$, c=7.8071 $\AA$. Hall effect shows a n-type conductivity in the sintered $HoSi_2$. The electrical resistivity values was 1.608${\Omega}cm^{-1}$ and carrier mobility was $6.9{\times}10^1cm^2/V{\cdot}sec$ at low room temperature.

We studied on structure and resistivity, temperature coefficient of resistance (TCR) of NiCr and NiCr-N thin resistor films prepared by do reactive magnetron sputtering of NiCr target. It is found that while pure NiCr films are polycrystalline, an addition of nitrogen (N2/(Ar+N2) ratios are between 10% and 70%) into the film is changed into amorphous structure and sheet resistance of films is increased. Measurement temperatures of TCR are ratios of $5^{\circ}C$ per 15min from $25^{\circ}C$ to $130^{\circ}C$. TCR for an as-deposited NiCr-N thin film is varied from positive to negative.

Josephson junction arrays of the type $Nb/Al-Al_2O_3/Nb$ were prepared by DC magnetron sputtering. The tunnel barrier was formed by in-situ thermal oxidation. Individual junctions were defined using selective niobium etching process(SNEP). The characteristic curves of Josephson junction arrays fabricated with and without cooling the substrate were represented. The junctions deposited without cooling showed poor characteristics(high leakage current, low gap voltage), and a high quality Josephson junction array of 2,000 junctions with high hysteresis was obtained with cooling and when operated at 74.6 GHz, it generated stable quantized voltage steps up to 2.2 V.

It was studied to prepare high temperature heating elements using molybdenum disilicide($MoSi_2$). Molybdenum disilicide is widely used as material for manufacturing high temperature heating elements. $MoSi_2$ heating elements could be used at 1700-1900$^{\circ}C$. However, it is relatively expensive, and its demand depends on import. $MoSi_2$ powders was mixed with 4-5wt% of montmorillonites type bentonite as plasticizer and a small amount of $Si_3N_4$, $ThO_2$, and B as additives to prepare specimen of heating elements. Then, it was extruded, dried, sintered and machined followed by heating test. Effects of sintering conditions and amount of additives were investigated, It was sintered effectively at 1,350$^{\circ}C$ for five hours. Electrical resistivity was decreased with increasing of sintering temperature and time, and related with apparent density of the specimens. It was linealy decreased with increasing of sintered density. The heating elements thus prepared was stable at 1700$^{\circ}C$ and the physical properties such as specific electrical resistivity, hardness, apparent density, thermal expansion coefficient, and bending strength were almost identical with those of commercial heating elements.

The 0.96$MgTiO_3$-0.04$BaTiO_3$ ceramics were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature and composition ratio by XRD, SEM and EDS. According to the X-ray diffraction patterns of the 0.96$MgTiO_3$-0.04$BaTiO_3$ ceramics, the hexagonal $BaMg_6Ti_6O_{19}$ and ilmenite $MgTiO_3$ structures were coexisted. In the case of the 0.96$MgTiO_3$-0.04$BaTiO_3$ ceramics sintered at 1325$^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 23.95, 70,200, -55.8ppm/$^{\circ}C$, respectively.

The $(Ba_{0.5}Sr_{0.5})(Nb_{0.5}Ti_{0.5})O_3$ [BSNT] ceramics were prepared by conventional mixed oxide method. The structural properties of the BSNT ceramics with sintering temperature were investigated by XRD, SEM, EDS. Increasing the sintering temperature, diffraction intensity of the BST(110) peak was increased. The average grain size of BSNT ceramics were increased with sintering temperature. In the case of BSNT ceramics sintered at 1550$^{\circ}C$, the grain was uniform and the pore was not existed. Increasing the sintering temperature from 1400$^{\circ}C$ to 1500$^{\circ}C$, the amount of Nb and Sr were decreased. The density of BSNT ceramics sintered at 1550$^{\circ}C$ was $1.125g/cm^2$.

Crack-free and homogeneous compact and epitaxial lead zirconate titanate(PZT) ferroelectric thin films with perovsikte structure have been prepared by sol-eel method. Tetrabutyl titanate, lead acetate and zirconium nitrate are used as raw materials. Glacial acetic acid is used as a catalyst. Ethylene glycol monoethyl ether is used as a solvent. The annealing temperatures of th thin films are 600~900$^{\circ}C$. The values of the remanent polarization Pr, and the coercive field $E_c$, of the PZT ceramic thin films are 46, 35 ${\mu}C/cm^2$ respectively.

This paper presents the results of materials and mechanical analyses and performance improvement of pull-off fitting used for catenary. The pull-off fitting is supporting the trolley wire which supplies the electricity. However, the pull-off fitting is repeatedly suffered by the mechanical stresses which produce cracks in the swivel clip, resulting in interruption of an electric car. The characteristic analyses of the swivel clip were performed and the improved swivel clip was suggested.

$Ba(Mg_{1-x}Co_x)TaO_3$[BMCT] ceramics were prepared by the conventional mixed oxide method. The ceramics were sintered at the temperature of 1525 $\sim$ 1625$^{\circ}C$ for 5hr. in air. The crystal structure of BMCT ceramics was investigated by the XRD. The microstructure of the specimens were observed by SEM. The structural properties of BMCT specimens were investigated as a function of composition and sintering temperature. All BMCT ceramics sintered over 1575$^{\circ}C$ were showed a polycrystalline complex perovskite structure without second phases and any unreacted materials. The density of BMCT (90/10) specimen sintered at 1575$^{\circ}C$ was 7.75g/$cm^2$. As the Co contents decreased, the ordering parameter of B-site in BMCT increased. The ordering parameter of BMCT(90/10) specimen sintered at 1575$^{\circ}C$ was 0.98.

본 논문에서는 채널과 드리프트 영역을 트랜치 안쪽에 형성하여 소자 크기를 줄임으로서 항복전압을 감소시키지 않고 낮은 온 저항을 얻을 수 있는 새로운 수직방향 채널 LDMOS(Lateral Double Diffused MOSFET)를 제안한다. 기존의 LDMOS 구조와 비교 할 때 동일한 60V의 항복 전압에서 소자 크기가 4${\mu}m$로 줄어들었고 이에 따라 온 저항은 절반의 수준으로 (0.45 m${\Omega}cm^2$) 감소하였다. 또한 소자 크기의 감소로 인해 전력용 집적회로를 구성할 때 집적도가 두 배 가량 증가하게 된다.

Polycrystalline silicon(poly-Si) films are deposited on low temperature glass substrate by Hot-Wire CVD(HWCVD). The structural properties of the poly-Si films are strongly dependent on the wire temperature($T_w$). The films deposited at high $T_w$ of 2000$^{\circ}C$ have superior crystalline properties; average lateral grain sizes are larger than $1{\mu}m$ and there at·e no vertical grain boundaries. The surface of the high $T_w$ samples are naturally textured like pyramid shape. These large grain size and textured surface are believed to give high current density when applied to solar cells. However, the poly-si films are structurally porous and contains high defect density, by which high concentration of C and O resulted within the films by air-penetration after removed from chamber.

In this paper, 200-class insulation system for form-wound stator coils is designed for form-wound stator coils is designed for AC traction driven with VVVF inverter. Model coils are made to embody all essential elements representing a winding insulation system and structure. Acceleration degradation for model coils is applied exposure to heat(235$^{\circ}C$). In order to investigate the condition of the coils and to determine their insulation reliability, high voltage test and the dielectric properties such as dielectric loss and capacitance are performed. Also, partial discharge measurement is investigated for internal defects.

The mechanical and phase transformation of the cold isostatically pressed $\beta$-SiC ceramic were investigated as a function of the sintering temperature. The result of phase analysis revealed 6H, 4H, 3C and phase transformation between 3C and 4H showed over 2000$^{\circ}C$ and the $\beta$ ${\rightarrow}$ $\alpha$ phase transformation was in saturation at 2200$^{\circ}C$. The relative density and the mechanical properties of $\alpha$-SiC ceramic was increased with increased sintering temperature. The flexural strength showed the highest value of 230 MPa at 2200$^{\circ}C$. This reason is because crack was propagated through surface flaw. The fracture toughness showed the highest value of 4.2 $MPa{\cdot}m^{1/2}$ at 2200$^{\circ}C$.

The $\beta$-SiC + $ZrB_2$ ceramic electroconductive composites were pressureless-sintered and annealed by adding 12wt% $Al_2O_3$ + $Y_2O_3$ (6 : 4wt%) powder as a function of sintering temperature. The relative density showed the highest value of 81.1% at 1900$^{\circ}C$ sintering temperature. The phase analysis of the composites by XRD revealed of $\alpha$-SiC(6H), $TiB_2$, $Al_5Y_2O_{12}$ and $\beta$-SiC(15R). Flexural strength showed the highest value of 230 MPa for composites sintered at 1900$^{\circ}C$. The vicker's hardness and the fracture toughness showed the highest value of increased with increasing sintering temperature and showed the highest of 9.88 GPa and 6.05 $MPa{\cdot}m^{1/2}$ at 1900$^{\circ}C$. The electrical resistivity was measured by the Pauw method from 25$^{\circ}C$ to 700$^{\circ}C$. The electrical resistivity of the composites showed the PTCR (Positive Temperature Coefficient Resistivity).

In this paper, the piezoelectric and dielectric properties as a function of x and r in $yPbZr_xTi_{1-x}O_3-(1-y)Pb(Mn_{1/3}Nb_{2/3})O_3$ piezoelectric ceramics is investigated. As a results, when y is 0.95 and x is 0.505, electromechanical coupling factor($k_p$), permittivity(${{\varepsilon}_{33}}^T/{\varepsilon}_0$), piezoelectric strain constant($d_{33}$) and mechanical quality factor($Q_m$) are 58[%], 1520, 272 [pC/N] and 1550, respectively. From XRD analysis, when x is 0.505, it is MPB which present rhombohedral and tetragonal phase in same quantity. Also, From SEM observation. when sintering temperature is 1150[$^{\circ}C$], grain size is about 2 [${\mu}m$]. As y decreases, piezoelectric and dielectric properties and curie temperature decreases, but mechanical quality factor and sintering temperature increases.

A new low-temperature poly-Si TFT employing a counter-doped lateral body terminal is proposed and fabricated, in order to enhance the stability of poly-Si TFT driving circuits. The LBT structure effectively suppresses the kink effect by collecting the counter-polarity carriers and suppresses the hot carrier effect by reducing the peak lateral field at the drain junction. The proposed device is immune to dynamic stress, so that it is suitable for low voltage and high speed driving circuits of AMLCD.

We have investigated about the grating formation of the $a-Se_{75}-Ge_{25}$ chalcogenide thin films. In this study, holographic gratings have been formed by using He-Ne laser(632.8nm) with different polarization states(linear, circular polarization). The diffraction efficiency was obtained by +1st order intensity of the diffracted beam. We have obtained maximum efficiency for Ag-doped thin film. It is observed the difference of the diffraction efficiency with polarization states. S:S-polarized state is shown high efficiency than the other polarization.

본 연구에서는 알루미늄 마스크를 이용하여 다결정 실리콘 결정립의 수평성장을 유도하는 새로운 엑시머 레이저 어닐링 방법을 제안한다. 제안된 방법은 비정질 실리콘 박막 위에 알루미늄 패턴을 형성하여 선택적으로 레이저 빔을 차단시키고, 액상 실리콘의 열을 금속박막을 통해 방출시킴으로써 다결정 실리콘 결정립의 수평성장을 유도할 수 있다. 제안된 레이저 결정화 방법을 이용하여 최대 1.6${\mu}m$의 수평성장 결정립을 형성하였고, 알루미늄 패턴의 경계로부터 결정립을 성장시킴으로써 결정립 경계의 위치를 제어하였다. 제안된 방법을 이용하여 제작한 다결정 실리콘 박막 트랜지스터는 기존의 다결정 실리콘 박막 트랜지스터에 비해 전계효과 이동도 및 온/오프 전류비 등의 전기적 특성이 우수하였다.

An SOI(Silicon-On-Insulator) LD(Lateral Double-diffused)MOS with graded gate and recessed source is proposed. The proposed structure can increase the breakdown voltage by reducing the electric field crowding at the edge of gate. Simulation results by TSUPREM4 and MEDICI have shown that the breakdown voltage of proposed device was found to be 52 V while that of conventional device was 45 V. At the same breakdown voltage of 45 V, the on-resistance of the LDMOS with graded gate and recessed source was 14.4 % lower than that of conventional structure.

신장병 진단에 중요한 요소의 농도를 측정하기 위한 요소 센서를 반도체 위에 개발이 연구의 목적이다. 센서의 감도 측정은 선형 전위 주사법(Linear sweep voltammtry)을 이용하였다. 선형 전위 주사법은 가역적이든 비가역적이든 관계없이 cottrell 식에 의한 전류와 농도의 직선관계로부터 감도를 측정할 수 있는 장점이 있고 또한 저 농도에서 민감하게 반응한다. 따라서 기존 전위차 측정형 바이오 센서(Potentiometric biosensor)에서 규명할 수 없는 감도 문제를 선형 전위 주사법으로 규명하고자 하였다. 센서전극은 p-type 실리콘 웨이퍼 위에 전극을 제작했다. 그 위에 cyclic voltammetry 법을 사용하여 전도성 고분자를 전기 중합 하였고, 그위에 다시 chronoamperometry법을 사용하여 우레아제를 고정화 하여 작업전극으로 제작하였다. 센서의 감도는 phosphate buffer 용액(pH7.4)속에서 온도 35$^{\circ}C$를 유지하며 측정하였다.

This paper deals with the change of surface Potential decay, surface resistivity, contact an91e and XPS of ultraviolet-treated PET films. From the experimental results on the surface Potential decay of UV degraded-samples, it was found that the accumulation of charge is decreased and the surface potential decay time is shortened. Also, from the result of XPS, it was found that the changes affected by the surface degradation of PET film were caused by the generation of carboxyl groups through the chain decomposition and recombination with oxygen molecules in the air.

초고속 전력선 통신을 위한 고주파수 대역에서 안정적인 자기적 특성을 갖는 Ni-Zn ferrite를 개발하기 위해서 투자율은 낮지만 주파수 특성이 우수한 $Ni_{0.8}Zn_{0.2}Fe_2O_4$를 기본조성으로 입자를 성장시키는 $Bi_2O_3$를 0.7, 비저항을 증가 시키는 CaO를 0.3, 그리고 입자를 균일하게 하는 $V_2O_5$를 0.1 wt% 첨가하여 미세구조를 제어하고, 다시 고주파 특성을 향상시킬 것으로 기대되는 $Co_3O_4$를 0, 0.3, 0.5, 0.7 wt%로 변화시켜 자기적 특성을 조사하였다. $Co_3O_4$가 밀도 및 미세구조에는 영향을 미치지 않았으나 0.3, 0.5 wt% 첨가시 첨가하지 않은 조성보다 투자율은 감소하였으나 사용 한계 주파수로 여겨지는 공명주파수가 각각 19.905, 19.205 MHz로 크게 증가하였다. 그리고 전체 전력 손실도 $Co_3O_4$를 첨가했을 때 감소하였으나 첨가량에는 큰 변화가 없었다. 와전류 손실이 전체 전력손실에 지배적인 영향을 미치고 있다.

다공질 실리콘을 대기에 노출시켰을 때 시간이 경과하면, 초기의 발광 특성이 변화하는 aging effect가 있다. 다공질 실리콘을 광 센서로 사용하기 위해서는 대기 중에 노출한 후 시간이 경과해도, 동일한 파장을 유지하여야 한다. 본 논문에서는 기체의 투과성이 낮고, 빛을 잘 투과시키는 폴리머들을 이용하여 다공질 실리콘 표면에 보호막으로 코팅하였다.

For the full color organic electro-luminescent device, essentially, red, green, and blue emissions are required. But red emission is not to reach minimum level of practical use 31[lm/W]. In order to optimize color purity and power consumption requirements, it is important for the materials development efforts to search for improvements in red emission effisiency. In this study, the bis(8-oxyquinolino)zinc II ($Znq_2$) were synthesized successfully from zinc chloride($ZnCl_2$) as a initial material. Then, we fabricated red organic electroluminescent device with a dye(DCJTB)-doped and inserted $Znq_2$ between emission layer and cathode layer for increasing EL efficiency. The hole transfer layer is a N,N'-diphenyl-N,N'-bis-(3-methyl phenyl) -1,1'-diphenyl-4.4'-diamine(TPD), and the host material of emission layer is $Znq_2$. For the inserting of $Znq_2$, efficiency increased.

A Dual Channel Trench IGBT (Insulated Gate Bipolar Transistor) is proposed to improve the latch-up characteristics. Simulation results by MEDICI have shown that the latching current density of proposed device was found to be 2850 A/$cm^2$ while that of conventional device was 1610 A/$cm^2$. The latching current desity of the proposed strucutre was 77.02% higher than that of conventional structre.

In this paper, a method was presented to estimate the contamination degree of outdoor insulator by the measurement of surface leakage current. Contamination is one of the most important factor to determine the performance of insulator. Thus, it is very important to exam the contamination degree on the outdoor insulator. There are many limits, such as reliability of data, interval of measurement and similarity of environmental conditions, in conventional method. So, the estimation technique for contamination has been needed to monitor the accurate pollution degree of insulator in situ. In this investigation, phase difference was measured to compare the variance of phase difference with the contamination degree and relative humidity. From the result, we could confirm the capability of the estimation method.

In odor to set high saturation magnetization and coercivity, it had need to orient axis of easy magnetization of CoCr-based thin film perpendicular direction(c-axis) to the substrate plane. It was known that crystalline orientation of CoCr-based thin film was improved by introducing underlayer like Ti, Ge. We prepared singlelayer and double layer with Si underlayer by Facing Targets Sputtering System. As a result, intensity and c-axis dispersion angle ${\Delta}{\theta}_{50}$ of singlelayer were improved with increasing film thickness. Also, it was found that CoCr/Si and CoCrTa/Si double layer showed good c-axis dispersion angle due to introducing Si.

ZnO : Al transparent conductive thin films were prepared by facing targets sputtering system with a DC power supply which can deposit a high quality thin films and control deposition condition in all range of $O_2$ gas ratio using ZnO target containing 8 at% of Al. Sputtering was carried out at a substrate temperature of R T with a DC current of 0.6 A and $O_2$ flow rate of 0 $\sim$ 0.9. The characteristics of ZnO : Al thin films was investigated by $\alpha$-step, four point probe, X-ray diffraction and UV/VIS spectrometer.

There is a wide climatic difference between Korea and foreign countries. Thus, the pollution cycle method, based on the climatic condition of Korea, is needed to evaluate the electrical properties of outdoor insulators. We make a analysis on the cycle methods of foreign countries, climatic conditions of Korea and failure data to make the cycle method. From the result, we can design a good pollution cycle method to evaluate the electrical properties of outdoor insulators.

In this study, The underwater object recognition using ultrasonic sensor fabricated with porous PZT-Polymer 3-3 type composites and invariant moment vector and SOFM(Self Organizing Feature Map) neural networks are presented. The recognition rates for the training data and the testing data were 98% and 94%, respectively.

The tantalum oxide($Ta_2O_5$) is an important material for present thin-film capacitor application owing to its high dielectric constant and thermal stability. We report dielectric property of Si(p type)/Pt/$Ta_2O_5$/Ag based MIM structure obtained by RF sputtering and annealed in vacuum environment. We have measured and researched the characteristics of C-F, C-V and EPMA. And we describe parameter dependence on sputtered condition and annealed temperature with dielectric property.

Recently polymer composite materials has been replacing the porcelain in suspension insulators as a insulating material. The polymer composite materials are introduced into Korea from the abroad, so there is, actually, no formal standard of assessment Both the porcelain insulator specifications and composite material test specifications are being used at the same time. The aim of this project is to establish a systematic standard suitable to current situations considering the trends of its production within Korea. This would protect the inner-markets against the market-opening and would promote the industrial development within a country.

$(Ba_{0.6-x}Sr_{0.4}Ca_x)TiO_3+yAl_2O_3$ wt% (x=0.10, 0.15, 0.20, y=0.5 $\sim$ 3.0) specimens were fabricated by the mixed-oxide method and then the structural properties as a function of the composition ratio and $Al_2O_3$ contents were studied. All BSCT specimens showed dense and homogeneous structure without the presence of the seconds phase. The sintered density was decreased with increase ad $Al_2O_3$ content. The Curie temperature and dielectric constant at room temperature decreased with increasing $Al_2O_3$ content. The dielectric constant and dielectric loss of the doped-0.5 wt% $Al_2O_3$ BSCT(50/40/10) specimen were about 3131 and 0.932% at 1KHz, respectively.

Optical and electrical properties of the $In_2Se_3$ single crystals grown by use of the Bridgman technique were examined in the transition temperature range between $\alpha$-phase and $\beta$-phase. $In_2Se_3$ single crystal has the rhombohedral structure and lattice constants are a=4.025 $\AA$, c=28.771 $\AA$ in C-axis. The transition temperatures of the stoichiometric $In_2Se_3$ single crystal is $10^{-2}{\Omega}cm^{-1}$ according to the specimens. However it varies rapidly in the transition region.

Plate-type ${\beta}-FeSi_2$ single crystals were grown using $FeSi_2$, Fe, and Si as starting materials by the chemical transport reaction method. The ${\beta}-FeSi_2$ single crystal was an orthorhombic structure. The direct optical energy gap was found to be 0.87eV at 300K. Hall effect shows a n-type conductivity in the ${\beta}-FeSi_2$ single crystal. The electrical resistivity values was 1.608$\Omega$cm and electron mobility was $3{\times}10^{-1}cm^2/V{\cdot}sec$ at room temperature.

방사선이 폴리에틸렌 박막의 결정구조에 미치는 영향은 결정구조의 전 영역에서 결정 격자의 결함으로 나타났으며, 이는 탄탄한 연결고리를 형성하고 있는 분자쇄의 단절로 인하여 결정 내부 및 표면에서 화학작용에 의한 기포가 발생한 것으로 판단된다. 또한, 방사선량의 증가에 따라서 그 결함은 비례적으로 증가하였으며, 주파수에 따른 유전특성 고찰결과는 10 MHz 이상의 범위에서 유전율이 급격히 증가하였다.

We have investigated for the modeling and the simulation of the ferroelectric capacitor and MFS TFT (Metal-Ferroelectric-Semiconductor Thin Film transistor). For ferroelectric capacitor modeling, we adopted the equivalent circuit model which consists of a nonlear capacitor, a nonliner resistor, and a linear capacitor. MFS TFT have been modeled by combining the ferroelectric capacitor and Bsim3 MOSFET model. Our simulations show the characteristics of ferroelectric capacitor and MFS TFT.

In this study, etching characteristics of polyimide(Pl) film with $O_2/CF_4$ gas mixing ratio was studied using inductively coupled plasma (ICP). The etch rate and selectivity were evaluated to chamber pressure and gas mixing ratio. High etch rate (over 8000$\AA$/min) and vertical profile were acquired in $CF_4$/($CF_4+O_2$) of 0.2. The selectivities of polyimide to PR and polyimide to $SiO_2$ were 1.15, 5.85, respectively. The profiles of polyimide film etched in $CF_4/O_2$ were measured by a scanning electron microscope (SEM) with using an aluminum hard mask pattern. The chemical states on the polyimide film surface were measured by x-ray photoelectron spectroscopy (XPS).

In this work, PZT thin films were etched as a function of $Cl_2$/Ar and additive $CF_4$ into $Cl_2$(80%)/Ar(20%). The etch rates of PZT films were 1600 $\AA$/min at $Cl_2$(80%)/Ar(20%) gas mixing ratio and 1973 $\AA$/min at 30% additive $CF_4$ into $Cl_2$(80%)/Ar(20%). Therefore the etch rate of PZT in $CF_4/Cl_2/Ar$ plasma is faster than in $Cl_2$/Ar. From XPS and SIMS analysis, metal halides and C-O, FCI and $CClF_2$ were detected. The etching of PZT films in Cl-based plasma is primarily chemically assisted ion etching and the remove of nonvolatile etch byproducts is the dominant step. Consequently, we suggest that the increase of Cl radicals and the volatile oxy-compound such as $CO_y$ are made by adding $CF_4$ into $Cl_2$/Ar plasma. Therefore, the etch rate of PZT in $CF_4/Cl_2/Ar$ plasma is faster than in $Cl_2$/Ar. The etched profile of PZT films was obtained above 70$^{\circ}$ by the SEM micrograph.

In this work the electrical characteristics of organic TFTs with the semiconductor-insulator interfaces have been interested. Pentacene is used as an active semiconducting layer. The semiconductor layer of pentacene was thermally evaporated in vacuum at a pressure of about $2{\times}10^{-6}$ Torr and at a deposition rate of 0.3$\AA$/sec. Aluminium and gold were used for gate and source/drain electrodes. before pentacene is deposited on the insulator, the gate dielectric surfaces of two samples were rubbed with lateral and perpendicular to direction of the channel length respectively.

Bi-layer Mo films were deposited on sodalime glass substrates using DC magnetron sputtering. As the gas pressure and power density, the resistivity varied from $1.5{\times}10^{-5}$ to $4.97{\times}10^{-4}{\Omega}{\cdot}cm$. Furthermore, stress direction yielded compressive-to-tensile transition stress curves. The microstructure of the compressive stress films which had poor adhesion consists of tightly packed columns, but of the tensile-stressed films had less dense structure. Under all gas pressure conditions, Mo films exhibited distinctly increasing optical reflection with decreasing gas pressure. The expansion of (110) peak width with the gas pressure meant the worse crystalline growth. Also, The highest efficiency was 15.2% on 0.2 $cm^2$. The fill factor, open circuit voltage and short circuit current were 63 %, 570 mV and 42.6 mA/$cm^2$ respectively.

In this paper, High quality factor and fine dielectric loss was resulted on specimen added 0.5wt% $MnO_2$ after compared and analyzed dielectric and piezoelectric properties following that added each 0 $\sim$ 0.9wt% of $Fe_2O_3$, $Nb_2O_5$, and $MnO_2$ on dopant at PSN-PT in two material disposition ceramics with research still is not completed to material investigation to increase high power piezoelectric actuator device efficiency. And, a measuring method and the experimental results of the temperature rise under the high vibrational velocity are also described.

In this thesis, specimens was manufactured in general method annexing PMB-PZT system ceramic, and the following conclusion has been deduced. In XRD, the crystal structure of ceramic has the tetragonal structure which is close to rombohedral structure, and consequently the specimen characterized by MPB was manufactured. According to dopping with xPMB, the dielectric constant at 20[$^{\circ}C$] reduced on the whole, dielectric constant was maximum value $8.0{\times}10^2$ at xPMB 0.01[mol%]. Dielectric loss was maximum value 4.1[%] at xPMB 0.01[mol%].

The physicochemical properties of the LB films were by AFM. We give pressure stimulation into organic thin films and then manufacture a device under the accumulation condition that the state surface pressure is 2, 10, 30[mN/m]. The stable images are probably due to a s interaction between the monolayer film and substrate. We are unable to obtain molecule res in images of the films but did see a marked co between images of the bare substrate and those the network structure film deposited ont Formation that prevent when gas phase stat liquid phase state measure but Could know o matter that molecules form equal and stable when molecules were not distributed evenly, accumulated in solid state only.

The displacement current measuring system used for detecting the dynamic behavior of monolayers at the air-water interface is described. It basically consists of a film balance, a pair of electrodes connected to each other through a sensitive ammeter. Here, one electrode is suspended in air and the other electrode is placed in the water. With Maxwell-displacement-current-measuring method, the phase transitons of Poly-$\gamma$-benzyl p-glutamate (PBDG) on a water surface were detected. Measured surface pressure, displacement current and dipole moment of monolayers of PBDG on the water surface. Also, we measured that compression velocity(30, 40, 50[mm/min]) when the sample spread volume was about 400[ul]. From the result, it is known that current is generated in the range of high surface pressures as compression velocity become faster.

To grow the diamond films by using RF-MW two step process, at first, diamond seeds were deposited on silicon substrate by RF plasma CVD, and then a diamond layer grown by MW plasma CVD on the seeds. The grain-size of diamond films deposited by using RF-MW two step process was smaller and denser and also, crystallity of diamond film was better than those of the MW plasma CVD process. The deposited diamond films were analyzed by SEM(scanning electron microscophy), XRD (x-ray diffraction), and Raman spectroscopy.

The radiation degradation of five insulating materials such as silicone rubber, ethylene-propylene rubber polybutylene terephthalte, poly carbonate, nylon 66 were evaluated by using thermogravimetry analysis (TGA) and tensile properties as a function of radiation doses. The results of temperature at 5% weight loss and activation energy from TGA showed linearly decreasing and increasing tendency as radiation doses comparing with tensile properties. Consequently, the assessment of TGA for the radiation degradation of materials was effective.

In this paper, the amount of additives in the electrode were investigated the relation of the mechanical properties and surface luminance of copper foil. Especially, organic compound of PEG(Poly-ethylene Glycol) was added from 1 to 20ppm for the propose of increasing the mechanical property and the surface state. The surface luminance of copper foil is appealed 69.25 at 2ppm-15A/$dm^2$ and 68.25 at 2ppm-10A/$dm^2$. It guess that 10ppm-10A/$dm^2$ occurred pin-hole. Tensile strength was not showed the significant difference but elongation appealed the most value at 5ppm-15A. We earned that the most PEG value of mechanical properties is 5 PPM.

In general, corona discharges in air are accompanied with electromagnetic wave which has wide frequency range up to UHF and can be detected by rod or loop antennas. But the existence of background noises such as TV, radio or electronic disturbances makes it difficult to separate corona discharge signals from them in the outside fields. The results of experiment using wideband antenna (30kHz - 2GHz) show that corona discharges have dependences on electrode types and independences on background noises.

The $Sr_{0.8}Bi_{2.4}Ta_2O_9$(SBT) thin films are deposited on Pt-coated electrode(Pt/$TiO_2$/ $SiO_2$/Si) using RF magnetron sputtering method. With increasing annealing temperature from 600[$^{\circ}C$] to 850[$^{\circ}C$], Bi-layered perovskite phase was crystallized above 650[$^{\circ}C$]. The dielectric constant is 213 at annealing temperature of 750[$^{\circ}C$] and dielectric loss have a stable value within 0.1. Leakage current density is $1.01{\times}10^{-8}A/cm^2$ at annealing temperature of 750[$^{\circ}C$].

Cyclic aging for 14 days is performed to remove a large amount of the volatiles found in freshly manufactured cable. In this paper, we examined lightning impulse characteristics of 22.9 kV CV power cable before and after cyclic aging for 14days. As the result, the breakdown voltage after aging under normal temperature was lower than that before aging, and the breakdown voltage after aging under hot temperature was lower than that before aging. We found that the dispersion of lightning impulse breakdown voltage before 14 cyclic aging test were reduced rather than those after 14 cyclic aging test.

To compare the lightning impulse measurement capabilities of high voltage laboratory, a lightning impulse voltage measuring system from HUT is circulated around the world. This paper presents test results after second round of this worldwide exercise. KERI's impulse voltage measuring system compared with the circulating reference measuring system from HUT at voltage levels of 80, 160, 240, 320 and 400 kV. Three impulse shapes were used, i.e. full smooth lightning impulse with both short (0.84 $\sim$ 0.95 ${\mu}s$) and long front (1.45 $\sim$ 1.56 ${\mu}s$), and chopped impulse with time to chopped impuse. Impulse peak value ($U_p$) and time parameters ($T_1$, $T_2$ and $T_c$) according to IEC 60060-1 were compared.

네트워크 분석기를 이용하여 GIS용 UHF 부분방전 검출장치가 CIGRE 권고안을 만족시킴을 보일 수 있는 방법을 제안하였다. 이 방법은 운전중인 GIS에서도 활용이 가능하며 주파수 영역에서 GIS 내 부분방전신호의 감쇠율을 정확히 측정할 수 있고 측정 시스템의 개별부품에 대한 교정이 필요치 않다. 또한 측정한 GIS의 구간별 감쇠율을 이용해 센서의 종류와 부분방전검출장치 및 GIS의 구성에 따라 센서의 위치를 손쉽게 결정할 수 있다.

In this paper, an novel optical measuring system based on the electro-optic effect has been proposed and realized using Pockels cell with a view to detecting partial discharge taking place at the needle plane electrode. This system has the following advantages ; nonmetallic probe sensor, immune to external EMI noise and broad band response of the Pockels cell from DC to GHz. And also it is constructed by He-Ne laser, optical fiber, $LiNbO_3$ Pockels cell, photo detector, grin lens, oscilloscope and PC. The characteristics of the developed prototype sensor are investigated under AC and corona discharges.

국내최초로 5 GHz 이상의 대역폭을 갖는 초고속 파형 측정장치를 이용하여 수 pC 의 부분방전이 발생 할 때의 전류를 측정하였다. 상용 GIS 환경과 유사한 $SF_6$ 가스로 절연된 부분방전발생 장치를 제작하였다. 장치 내부에 작은 금속 이물질을 투입하고 부분방전을 발생시켰다. 부분방전시의 전류는 전압분배기와 전류프로브에서 측정되었다. 전류의 상승시간은 약 80 ps 이었고 반치폭은 약 105 ps 이며 이때의 방전량은 60 pC로 측정되었다. IEC270 방법에 의한 측정에서는 7 pC 으로 측정되었다.

자유 도전성 파티클이 전계의 영향으로 GIS (Gas Insulated Switchgear) 외함전극 내부표면으로부터 가스공간을 가로질러 중앙도체까지 튀어 오르게 되면 절연파괴가 발생할 가능성이 매우 높아진다. 그러므로 파티클이 튀어 오르는 높이는 절연파괴 발생 위험도를 평가하는 데에 중요한 자료로 활용될 수 있다. 본 논문에서는 GIS 내부에 자유 도전성 파티클이 혼입된 상태에서 GIS가 운전중일 때 GIS 외부에서 파티클 상승높이를 추정하는 방안을 세계 최초로 제시함으로써 현재까지 해결되지 않은 도전성 파티클 결함에 대한 절연파괴 위험도 평가가 가능하게 되었다.

고전압 시험 진행시, 시험전압의 파고치, 순시강하, 정현파로부터의 편차, 규약 파두장과 같은 시간특성을 측정할 때는 일반적으로 IEC60060-2에 따른 인증절차를 거친 장치를 사용해야 한다. 최근 LG산전 전력시험 기술센타의 고전압 시험실은 기존의 아날로그 오실로스코프를 디지털 오실로스코프로 교체하고 PC와 GPIB를 이용해 시험변수의 자동 계산을 위해 관련 소프트웨어를 개발했다. 또한, 새로 구축한 측정시스템의 성능검증을 위해 산업체 인증기관인 LG산전이 보유하고 있는 기준계측시스템과의 비교시험을 실시하고 측정 불확도를 산출하였다. 따라서 본 논문에서는 새로운 측정 시스템에 적용한 성능시험방법과 불확도 산출방법, 소프트웨어의 기능과 성능에 대해 소개하고자 한다.

삼상 교류에 의한 플라즈마 발생 장치 중구리튜브 전극을 이용한 아크 글라이딩 식의 비이행형 플라즈마 발생장치는 전극구조가 간단하고 교체가 용이 할 뿐 아니라, 전극과 노즐의 형상을 유해 가스 처리에 충분한 엔탈피를 가지도록 설계될 수 있으므로, DC형과 더불어 차세대 환경정화용 핵심장치로 관심을 모으고 있다. 본 연구에서는 교류형의 특성상 어쩔 수 없이 발생하는 열플라즈마의 플리커를 제어하기 위해 글라이딩 아크의 움직임과 플라즈마 플래임의 움직임을 분석하여 열 플라즈마의 안정화 조건을 정립하고자 하였다. 또한 본 논문에서는 여러 가지 조건에서 수행된 플라즈마에 관련된 수치해석과 플라즈마 발생기의 동작시험의 결과를 바탕으로 삼상교류 열플라즈마를 안정시킬 수 있는 기본적인 조건의 범위를 제시하였으며 이에 대한 토의를 기술하였다.

In this paper, a short-term test method to diagnose and estimate the lifetime of AC PDP(Plasma Display Panel) has been proposed. As using this method, we investigated the lifetime of MgO layer in AC PDP. The lifetime was increased in proportion to an MgO thickness but it was allowed when the MgO thickness was raised until 5000$\AA$. Over 5000$\AA$, the lifetime was saturated with a thickness of MgO layer.

Nowadays, the most serious problems in AC PDP are high cost and a complex manufacturing process. To solve these problems, Fence electrode structure are newly suggested. In this paper, we investigated the the electrical and optical characteristics as the structure of Fence electrode was changed, and suggested the optimum width and arrangement of electrode.

In ac plasma display(PDP), an image quality mainly depends on the contrast ratio. And the contrast ratio is affected by the driving condition and size of discharge cell. In this study, the electrical and optical characteristics during reset, address and sustain discharge were investigated as the height and width of barrier rib were varied in order to obtain the highest contrast ratio. As a result, the optimum rib height and width were 140${\mu}m$ and 600${\mu}m$, respectively.

ac PDP 동작에 있어 미량 불순물 가스는 panel 내의 휘도 및 방전 특성에 많은 영향을 미칠것으로 생각된다. $O_2$, O, C 및 $H_2$와 같은 불순물 가스는 ac PDP의 제조 공정 중에 발생하거나, 충전된 방전가스에 혼합되어 발생하는 등 여러 가지 원인으로 나타난다. 이 논문에서는, ac PDP의 동작 가스 중에 미량의 불순물 가스(Ar, $N_2$, $O_2$, $H_2$, $CO_2$)를 주입하여, 이 미량의 불순물 가스로 인한 ac PDP의 휘도 및 방전의 특성변화에 대한 관계를 조사하였다. 그 결과, $O_2$ 가스의 분압이 $2{\times}10^{-3}$/He+Ne+Xe(4%)일 경우, 방전전압은 12% 증가하였고, 휘도는 60% 감소하였다. 또한, $CO_2$ 가스의 경우는 방전전압은 14% 증가하였고, 휘도는 44% 감소하였다.

The voltage controlled ramp waveform(VCR) has recently been used in the reset period prior to addressing for plasma display. However, in this paper, the current controlled ramp waveform(CCR) which may prevent the oscillation of gap voltage cause current growth and decrease the background luminance has been suggested. As a result, in case of CCR method, the contrast ratio was about 14% increased compared with VCR method, whereas the addressing and sustainin discharge characteristics of CCR method were same with those of VCR method.

In this paper, the electrical characteristics of Insulating paper, for pole transformers, subjected to accelerated ageing were observed and the results were compared with those of virgin insulating paper. For the experiment, insulating materials for pole transformers were enclosed together in an oil bath and thermally aged under the real pole transformer operating conditions. After the accelerated ageing of the insulating materials, the dielectrics were measured and compared with the results of the virgin ones.

The purpose of this paper is to provide the fundamental data which can be used for the design of pole transformers. For the purpose, electrical characteristics of aged mineral oil and silicone oil were analyzed by comparing with the results of virgin ones. For the experiment, an oil bath which can keep constant temperature was constructed to thermally deteriorate the specimens. And transformer materials were put together in the bath according to the their ratio in weight in the pole transformer. And the parameters such as relative permittivety, tan$\delta$ and specific resistance were measured. As a results, the permittivity of silicone oil was higher than that of mineral oil, and its decreasing rate with temperature was also higher. In addition, it was found that tan$\delta$ and specific resistance of virgin and aged oil began to differ at similar temperature.

In this paper, two types of surge voltage generated in the only operation of capacitor bank composed of paralleled multi-modules are analyzed and also studied to suppress those. The surge voltage can give malfuction to the operation of capacitor bank and destroy the expensive components at the worst. The conditions and causes of surge voltage generation and the countermeasure for suppression are presented.

A pulsed power supply of 2.4MJ capacitor bank has been developed to make investigation into electric gun technology. It is made up of eight paralleled 300kJ modules, and can supply various shape of high current pulse by changing charging voltage, inductance, capacitance, and firing time of each module. The 300kJ module has been designed and fabricated for the maximum operating voltage of 22kV, peak current of 150kA, and pulse duration of 1msec. The experiments of the modules were done, and the equivalent circuit of the module was determined. The characteristics of the module were analyzed more deeply through the circuit simulation. The experiments of the paralleled modules with inductance of 20 $\mu$H and load resistance of 100 m$\Omega$ were performed, where the modules were discharged simultaneously and/or sequentially. The results of the experiments were analyzed. The 2.4MJ capacitor bank is currently used as the pulsed power supply for the ETCG (Electro Thermal Chemical Gun) research.

Eight 300kJ modularized capacitor-banks have been constructed. These modules have been installed and assembled to make a 2.4MJ pulse power system (PPS). This 2.4MJ PPS was developed to be used as a driver of an electrothermal-chemical (ETC) gun. Each capacitor bank has six 22kV, 50kJ capacitors connected in parallel. A triggered vacuum switch (TVS-43) was adopted as a main pulse power-closing switch in each module. The module also contains a crowbar circuit made of three high-voltage diode-stacks, a multi-tap inductor and an energy-dumping resistor. Various current shapes have been formed by a sequential firing of multiple capacitor banks. Resistive dummy load has been used and various combinations of experimental parameters, such as charging voltage, trigger time and inductance, were tested to make flexible current shapes.

In connection with the monitoring of the insulation degradation of the large power apparatus, a statistical treatment, such as phase resolved partial discharge analysis (PRPDA) has been established for the on-line monitoring system during the past two decades. However, it has shown some inconveniences to distinguish the nature of the PD source in power apparatus. In this regard, a novel approach based on the chaotic analysis(CAPD) is proposed describing the fundamental ideas, outcomes and different view points from conventional PRPDA. In order to make a model for the possible defects causing sudden failures in service, several types of specimen were prepared. And partial discharge signals, originated from those samples, were measured and analyzed by means of PRPDA and CAPD respectively. In this paper, it seems that the correlation between the consecutive PD pulses depending on the nature of PD could be investigated by CAPD. Therefore, it could be considered that the nature of PD source can be distinguished more distinctively when the PRPDA is combined with CAPD.

A large cross-section pulsed electron beam generator of cold cathode type has been developed for industrial applications, for example, waste water cleaning, flue gas cleaning, and pasteurization etc. The operational principle is based on the emission of secondary electrons from cold cathode when ions in the plasma hit the cathode, which are accelerated toward exit window by the gradient of an electric potential. The conventional electron beam generators need an electron scanning beam because the small cross section thermal electron emitter is used. The electron beam of large cross-section pulsed electron beam generator do not need to be scanned over target material because the beam cross section is large by 300$cm^2$. We have fabricated the large cross-sectional pulsed electron beam generator with the peak energy of 200keV and beam diameter of 200mm and obtained the large area electron beam in the air. The electron beam current has been investigated as a function of accelerating voltage, glow discharge current, helium pressure, distance from the exit window and radial distribution in front of the exit window.

포항 방사광 가속기 2.5 GeV의 전자선형 가속기는 마이크로웨이브 발생원으로써 80 MW 클라이스트론(klystron) 11대와 입사부에 65 MW 클라이스 트론 1대를 사용한다. 전자빔 에너지의 효율적인 제어를 위하여 고출력 클라이스트론의 RF 전력과 입력 빔의 전력을 정확하게 측정해야 하며 응답특성이 양호한 측정장치와 정밀한 측정이 요구된다. 클라이스트론에 공급되는 전력은 캐소드에 인가되는 전압과 전류의 측정치로 계산된다. 비록 빔 전압측정에서의 작은 오차일지라도 클라이스트론 RF 출력 전력의 결과값에 큰 영향을 미친다. 따라서, 빔 전압의 측정시에 정확한 측정을 위하여 특별한 주의가 요구된다. 고전압 펄스전원장치 인 모듈레이터 (modulator)에서 발생되는 수백 kV(350-400 kV)의 전압을 측정하기 위하여 커패시터의 용량비로 입력전압을 분압하는 용량성 분압기(capacitive voltage divider, CVD)가 사용된다. 고압측 분압용 표준 콘덴서의 정전용량을 결정하는 주요인자는 고전압 절연유의 유전율(dielectric constant)이다. 그러므로, 측정범위 내의 전압, 주파수, 온도에 대하여 정전용량의 변화율이 작도록 설계하여야 한다. 본 논문에서는 펄스형 고전압 신호 측정을 위한 용량성 전압 분배기의 측정원리, 설계분석, 교정시험, 절연유의 온도변화에 따른 정전용량 변화 특성에 대한 실험 결과를 고찰하고자 한다.

In recent the on-line partial discharge (PD) measurement using sensors, such as EMC, SSC, RTD and RFCT, as an indicator of stator winding insulation condition has been developed. RFCT sensor was placed arounding a grounding lead of surge capacitor to detecting PD. Trend of PD magnitude/phase angle/pulse number over time are useful parameter to diagnosis aging state. We have developed Radio Frequency Current Transformer(RFCT) sensor which is suitable for PD diagnostic measurement in 6.6kV rotating machines. In this paper, we describe the characteristics of RFCT sensor, such as frequency and PD magnitude using 6.6 kV model stator winding in Lab.

Recently many researches on the diagnosis of stator winding insulation for large rotating machines have been developed sine the 1970s. Capacitive coupler has been the most widely used sensor for on-line partial discharge(PD) in rotating machines. The 105 [pF] ceramic coupler(CC) has been developed to continuously measure the PD activity in operating motor stator windings. This paper presents frequency characteristics and laboratory test to compare traditional 80 [pF] epoxy-mica coupler(EMC) and 105 [pF] CC for PD measurement in 6.6 [kV] stator windings.

This paper describes a monitoring program for a substation preventive diagnostic system. The monitoring program announces the condition of the transformer and GIS like normal, warning, abnormal and danger from the absolute value of data or change trend to user. The developed system is operating in 345kV U-Ryung substation for performance and environment tests.

본 연구는 AC 전원을 인가하여 좁은 전 극간격에서 고수율을 얻을 수 있는 연면방전방식 (Surface Discharge type)과 DC 전원을 인가하여 넓은 전극간격에서 저수율을 가지는 DC방전방식(DC Discharge type)을 중첩방전 할 수 있도록 중첩방전관을 설계 제작하여 각각 독립적인 방전방식을 적용하였을 때의 방전전압, 방전전류, 방전전력 및 오존생성농도를 실험적으로 조사하고, 두 방전방식을 동일공간에 중첩방전하여, 위 실험을 반복하고 중첩방전이 동일방전공간에 투입에너지 밀도를 높임으로써 방전특성 및 오존생성 특성을 비교 분석하였다.

The high voltage measuring systems used in the testing systems shall be required to maintain the traceability to the national or international standards by the IEC 60060-2. Also all testing laboratories should prepare the documents evaluating the measurement uncertainty of the tests. By the way, this paper introduces the principal of IEC about the maintenance of traceability and evaluation methode of uncertainty.

In manufacturing processes, various and suitable pulse shapes are required for the purpose of material processing and the pulseshape is regarded as a dominant factor due to the specific property of processing materials. Therefore, in this study, a variable pulse width, high duty cycle Pulse Forming Network(PFN) is constructed by time sequently. The power supply for this experiment consists of three switching circuits. The PFN elements operate at low voltage and drive the primary of HV leakage transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence of properly phased and nested increments. We investigated laser pulse width as various delay time among three switching circuit. As a result, we tan obtain various laser pulse width from about 4ms to 10ms. The maximum laser pulse width obtained at this experiment was about 10ms at delay time of 4ms among each switching circuit.

We have developed the global assessment system for medium voltage power cable systems. Our purpose of diagnostic activity is the economic discrimination and maintenance of bad cables which is likely to cause cable system failure. We have atapted the Voltage Decay Method to construct the power cable assessment system for our diagnostic purpose. From the field application test results, we have concluded that our system is successful and convenient for the discrimination and maintenance of the damaged cables economically.

Air arc interruption used in low rated voltage breaker, ACB and MCCB, have used the arc chamber composed of metal plates and insulating laminates which supposed these mechanically. and geometry and materials of arc chamber are very different by breaker manufacturer. These breakers have required to be smaller and to interrupt higher current by user. therefore the arc chamber geometry and material in breaker have been small, complex and various. The purpose of this study is to examine the effects of insulating laminates and contact materials on air arc interruption. Contacts were surrounded by a rectangle chamber of insulating laminates. Contact concoctions were composed of AgW, AgCdO that have used in low rated voltage breaker, and insulating laminates were polyester, epoxy. We found strong dependance of arc voltage on insulating material. The ablated vapor on polyester increased arc voltage that was useful in air arc interruption.

본 연구에서는 금속와이어를 자동으로 공급할 수 있는 피딩장치와 금속와이어가 전극에 일정거리 도달하면 자발방전에 의하여 나노분말이 제조될 수 있는 챔버, 그리고 충전기 등의 장비 일체를 제작하여 연속적인 전기폭발 실험을 행하였으며, 이렇게 제조된 분말입도와 공정 중에 나타나는 펄스방전 특성과의 상호연관성을 조사하였다. 그 결과, 진동이 없는 전류 파형을 갖는 경우에 나노분말을 제조하기가 가장 적합함을 확인할 수 있었다.

플라즈마 잠김 이온주입 장치를 개조하여 플라즈마 잠김 이온주입 및 증착 장치를 제작하였다. 박막을 증착하기 위하여 마그네트론 스퍼터를 장착하였다. Si 시료에 TiN막을 형성하기 위하여 $PI^3$

This paper described the outputs of acoustic sensors due to the vibration of particles in the mock up GIS. We used the two type of acoustic sensors which had 150kHz resonant frequency and 60kHz resonant frequency respectively. In the experiment of the mock up GIS, we paid attention to the magnitude and attenuation of sensor outputs due to particles. In this results the output of each sensor in frequency characteristic depended on the material of GIS tank and the output of sensor in magnitude characteristics depended on the size of particles and dropping height.

The effect of ribbed spacers having metallic particle attached to the post-type spacer on dielectric breakdown phenomena has been investigated using electric field analysis for imaginary streamer process and a breakdown experiment. It was described that the electric field analysis and the dielectric breakdown test were performed on the case that the particle was attached to the various position of the ribbed spacer having various shapes. As a result, the breakdown voltage of the spacer with two ribs was highest, and it was varied by the length and the thickness of the rib. Especially, in case of the rib with round edge, the breakdown voltage was higher than that with rectangular edge, which complied with the result through the field analysis.

A comprehensive model of ozone generation in dielectric barrier discharges is presented. The model combines the physical processes in the microdischarges with the chemistry of ozone formation. It is based on an extensive reaction scheme including the major electronic and ionic processes. The importance of excited atomic and molecular states is demonstrated. Theoretical limits are given for the ozone production efficiency and the attainable ozone concentration. The most important parameters influencing the performance of ozonizers are identified.

Ozone is widely used to sterilize food and tap water because ozone is a strong oxidizer. Efficient ozone generation is the most important issue in the field of ozone application. A variable discharge type of ozonizer that generates diffuse glow discharge in air at atmospheric pressure was used for the efficient ozone generation.

Because the overhead transmission lines are exposed to the outdoor weather, the faults of the transmission lines are due to natural conditions, and among these faults, the outage rate by lightning is about 50%. The lightning causes the damage of power system equipments, the shut down of electricity and the electro-magnetic interference. Therefore, the pertinent insulation design is important, not only to decrease the damage of the facility itself but also to increase the reliability of electric power system. For these reasons, we have to obtain and accumulate the lightning current parameters for the basic lightning research. This paper describes the statistical distribution of lightning current parameters and the IKL map.

This paper describes the dielectric characteristics of composite dielectric film for pulsed power capacitors. The relative electric permittivity(${\varepsilon}'$) and the dielectric dissipation factor(tan$\delta$) were measured for polypropylene (PP) membranes, kraft paper for capacitors(CP) and composite dielectric films(PP+CP), respectively, in a frequency range of $1{\sim}10^4$[Hz], and in temperatures ranging from -50[$^{\circ}C$] to 110[$^{\circ}C$]. As a result, the variation of the electric permittivity was observed similarly for PP and CP. Dielectric dispersion was observed in frequency domain in PP, CP and composite dielectric films.

This paper presents the development of electromagnetic wave detecting equipment for diagnosis of enclosed switchboard. High voltage power equipments are very important equipment of the key industries and the private enterprise. Power line accidents are national plans because of those set off casualties lose of power equipments and communication networks. Therefore the necessity of the development of detecting for power equipment diagnosis is demand for prevention of high voltage equipment accidents. This paper is the development of electromagnetic wave detecting equipment for diagnosis of high voltage equipment. This paper establishes the diagnosis method for high voltage power equipments, that secures original technique and possesses detecting technique for electromagnetic wave. By the study we developed electromagnetic wave detector, and we applied this equipment application tests at the place constructed high voltage equipments.

The clack of Insulator, which results from internal or external surges such as electrical, mechanical, and thermal stress, might cause ground fault and a power failure without proper repairs. In order to minimize losses caused by a short-term or long-term power failure, it is necessary to detect the deteriorated insulator as early as possible. To do so, we will develop a new device, which can detect and trace an deteriorated insulator by monitoring its physical change the variation of frequency spectrum. This device will do so by finding a Periodic wave sharp (120 Hz), a peculiar wave generated by defused electricity.

In compared with air insulated switchgear GIS has a high efficiency and confidence. Insulation method using $SF_6$ gas has a very excellent insulation characteristics for high voltage equipment but has a characteristics that insulation heredity is changed for internal unequal electric field. So analysis of electromagnetic field in GIS is very important basic data for structure design and trouble diagnosis process. In compared with established method, SNM in this paper observes variation of the electromagnetic field with real time and get result very similar to measurement. In order to know the variation of electromagnetic field distribution for transient response for time and position, variations are observed when metal particles are moving fast.

In this paper, Partial Discharge(PD) patterns are compared by means of Low Frequency PD(LFPD, based on the IEC 270) and recently proposed High Frequency PD(HFPD). For this purpose, three different types of artificial defects are provided such as corona in air, void in epoxy insulator and needle defect in XLPE cable insulation. PD were generated from each defect and then detected respectively by two different methods such as LFPD and HFPD. As a result, remarkable resemblance in PD pattern for differ detecting method have been observed from each defect. Accordingly, it could be deduced that the pattern recognition by LFPD could be regarded as the reference for the investigations by HFPD.

In general, power demand is on an increasing trend as industries have made rapid strides. Power transformer is the most important equipment in substation for this reason. Transformer trobles go with blackout, expensive repair costs and huge economic losses. Therefore it is important to find the quick detection of incipient fault for the least losses. There have been gas, partial discharge, temperature, OLTC, fan and pump diagnosis for preventive techniques by present. Specially gas analysis has been adapted for a long time and proved as confident method. In this paper, we analysed the fault causes of used power transformer. The insulation faults was occupied 40% of inquired 152 faults from 1991 to 2000. This study presents the developed algorithm and expert system for finding abnormal status within transformer. We used the Element Expert tool developed Neuron DATA Inc.

In this paper, As the wavelet transform has the properties of multi-resolution analysis and time-frequency domain localization, application of wavelet transform is used at partial discharge(PD) signal detected by electromagnetic wave detection method to extract PD signal's various frequency component and its time domain. therefore we can analyzed PD signal's time-frequency domain simultaneously. On the other hand, using wavelet transform denoising process, inclued noise signal in detected PD signal is well elimiated. we can propose the true shape of PD signal.

In removing the flue-gas using electrical discharge method, it is important to dissociate or ionize the atoms and molecules by the collisions with energetic electrons and it produces the radicals that are used to decompose the pollutants. For that purpose, a bidirectional pulsed voltage is used to produce lots of energetic electrons efficiently and increase the power efficiency. The simulation is performed with changing the pulsewidth under the fixed applied voltage. The particle-mesh model coupling the NGP(nearest-grid-point) to FEM(finite element method) is used to simulate the behavior of electrons and the spatio-temporal variation of the electric field for the streamer in discharge tube.

변전소 및 전력계통에 지락사고가 발생하면 변전소의 접지망에 사고전류가 유입하게 된다. 이 유입전류는 가공지선이나 변압기 중성선 그리고 기타 접지 망에 연결되어 있는 접지시스템에 의해 분류되는데, 모델변전소의 지락전류 흐름도를 모델화하여 Pspice 프로그램으로 대략적인 분류율을 계산하고, 실측치를 통해 지락사고시의 가공지선 분류율을 비교 평가하였다.

The mechanical characteristics of XLPE cable is basic to the installation design. Especially, snake and offset design require accurate coefficient of linear expansion($\alpha$), Young's modulus(E) and bending stiffness(El) of the cable. In this paper, $\alpha$, E and El of 345kV XLPE cable was measured by experimental setup, and verified by measuring axial tension and lateral displacement in snake installation.

펄스형 Nd:YAG 레이저는 연속형에 비해 효율이 높고 높은 첨두 출력(peak power)이 가능하므로 가공에 있어서 여러 가지 장점이 있다. 더구나 레이저 펄스 모양을 가변시키는 기능은 펄스형 Nd:YAG 레이저로 가공하기 힘든 특수분야에까지 가공을 가능하게 하였다. 본 연구에서는 3개의 플래쉬램프를 순차 점등시키는 MD(multi-discharge)방식의 레이저 시스템을 설계 및 제작하여, 램프 점등 시간의 변화에 따른 레이저 빔의 펄스폭과 펄스 세기(펄스 크기)를 조사하였다. 즉, PIC One-Chip microprocessor를 이용하여 실시간으로 3개의 플래쉬램프를 순차적으로 점등시켜 보다 다양한 펄스 모양을 만드는 기술을 개발하였다. 위 방식의 장점은 램프의 점등 지연시간을 0 $\sim$ 10ms 까지 다양하게 변화시킬 수 있고, 외부의 키보드로 실시간 제어가 가능하므로 보다 편리하게 펄스 모양을 변화시킬 수 있다. 또한 긴 펄스를 만들 수 있어 산업용 가공이나 의료용으로 널리 사용될 수 있을 것이다.

Partial discharge(PD) tests are used to evaluate the insulation condition of stator windings in six 6.6kV motors. These tests were conducted using a conventional partial discharge detector (PDD), turbine generator analyzer(TGA) and partial discharge analyzer(PDA). Off-line PD measurements were performed on six 6.6kV motors. PD magnitudes ranged from 740 pC to 5,100 pC at the normal line-to-ground voltage. Six 6.6kV motors have been equipped with eighteen 80pF epoxy-mica couplers(one per phase) on the motor terminal boxs. The PD pulse from sensors were measured with the TGA and PDA instruments on a normally operating motors. The PDD, TGA and PDA test results showed that internal discharge was detected in voids of the groundwall insulation.

In this paper, the circuit of AC Choppers for $CO_2$ laser power supply are proposed and investigated. IGBT-controlled ac voltage regulators, operating at high frequency chopping mode. Chopping-to-supply duty ratio plays an important role in terms of laser output. Laser input energy is varied by controlling the leakage transformer used with the proposed system. This improved circuit employs a 3 electrode - type and Ring Blower. This improved circuit system has many advantages compared with the conventional SMPS such as simple design requirement, easy implementation, high reliability, low switching loss, and consequently high efficiency. As a result, the maximun output was 16W at duty-ratio of 92%, total gas mixture of $CO_2$ : $N_2$ : He = 1 : 9 : 15, total pressure of 15torr.

This paper describes that PD sources in GIS were recognized using fuzzy algorithm proposed in this paper. PD sources were classified by four states and PD signals were expressed by $\phi$-q distribution. $\phi$-N distribution and Q-N distribution. Then statistical operators were extracted from each distributions. As a result, the rate of recognizing PD sources in GIS using fuzzy algorithm proposed in this paper was 93[%].

The pulsed Nd:YAG laser is used widely for materials processing and medical instrument etc. It is important to control the laser energy in those fields using a pulsed Nd:YAG laser. In this paper, constant-frequency current resonant half-bridge inverter and Cockcroft-Walton circuit are used to charge the energy storage capacitor variably. This laser power supply is designed and fabricated which has no high-voltage transformer, less switching losses, compact size and capability in varying the laser output power. Also, the output characteristics of this Nd:YAG laser system are investigated. The tested results are described.

Nondestructive tests are used to evaluate the insulation condition of stator windings in rotating machine. These tests included ac current, tan delta and maximum partial discharge. The insulation condition of stator windings was assessed by three test items. The stator windings were generally in good condition, wash, reimpregnation and rewind. It was confirmed that nondestructive tests were most useful method to indicate the insulation condition of stator windings.

The remaining life of ACSR(Aluminum Conductor Steel Reinforced) wires exposed to the atmosphere for a long period relies on the extent of deterioration caused by environmental factors such as atmospheric corrosion, galvanic corrosion, crevice corrosion and fatigue corrosion. We investigated the tensile characteristics of ACSR wires in a coastal area through several mechanical tests, and analyzed the constituents of them using SEM(scanning electron microscope). Test samples are parts of ACSR 97[$mm^2$] overhead transmission lines in that area. The result shows that ACSR wires exposed to salt may lead to rapid mechanical deterioration.

This paper deals with the development and application of an inner corrosion detector for the ACSR(Aluminum Conductor Steel Reinforced) power lines. The detector runs on an ACSR power line and inspects the inner corrosion of the conductor using the technology of the nondestructive eddy current test. It is consists of an ECT sensor, signal processing units, a RF transmitter/receiver, and etc.. The experimental result through field tests shows the detector can efficiently find both the zinc and aluminum loss of ACSR power lines.

The partial-discharge(PD) is accompanied by physical and chemical phenomena, such as heat, light, noise gas, chemical transformation, electric current, and electromagnetic radiation. The PD can be detected by measuring one of these changes. Although some techniques are employed in this purpose, several obstacles interfere with an on-line measurement. Now, a fiber-optic sensor for detecting ultrasonics is suggested for the on line measurement system with high accuracy. This paper describes the basic principles fiber-optic sensor for ultrasonic measurement.

The route of surge arrester connection is very important because bends and kinds of leads increase the impedance to lightning surges and tend to nullify the effectiveness of a grounding electrode conductor. There is a need to know how effective installation of lightning surge arresters is made in order to control voltage and to absorb energy at high lightning currents. The effectiveness of a grounding conductor and bonding for 18[kV] metal oxide distribution line arresters was experimentally investigated with lightning and oscillating impulse voltages.

With the rapid development of electronics industry and information-oriented society, the threat of fields radiated from electrostatic discharges (ESDs) to the electronic equipments is becoming more and more dangerous. To apply a proper protection method this paper presents the results of the measurement of the voltage and current peaks and the rise time of ESD derived from a charged human body under a variety of experimental conditions.

This paper deals with the characteristics of the potential rises of down-conductor due to lightning surge currents. Direct lightning strikes can cause high impulse currents to the lightning protection system(LPS) of a building. These high impulse currents have the front time as short as 1[${\mu}s$]. In this case, the induced voltages caused in a closed circuit inside the building can be very high and cause damage or submit people to electric hazard. So, the LPS has to be designed to ensure safety condition to person and acceptable levels of induced voltages to the electrical and electronic equipments. The results of the potential rises related to the bonding conditions between the grounding conductor and metal raceway and the type of down-conductors are introduced.

Partial discharge testing are rapidly becoming the most powerful tool to assess the condition of high voltage generator and motor stator windings. Recently, on-line monitoring scheme with trending technique is widely applied in insulation diagnosis. This paper describes the on-line partial discharge detecting techniques in the high voltage motor stator windings. Also, on-line monitoring system for an insulation diagnosis are proposed.

인축의 안전 및 기기보호를 위해 시설하는 접지설비는 수평 및 수직 접지도체와 접지단자 그리고 접지콘넥터 등으로 구성되어 있다. 이러한 접지설비는 포설조건에 따라 전기적 기계적 화학적 변화를 일으켜 시간이 경과함에 따라 접지시스템의 안전성과 신뢰성을 경감시키게 된다. 따라서, 대책을 갈구하기 위해 각종 접지설비의 시편을 채취해서 경년변화 특성을 분석하였다.

The purpose of this experiment was to develope Triggered Vacuum Switch(TVS) and to improve understanding of the high current vacuum arc phenomena in the TVS. The TVS has an array of rods of alternate polarity in which a fixed gap spacing is maintained between the rods. The cross section of each rod has trapezoidal shape. Breakdown of the TVS produced high current vacuum arc plasma. A spectroscopic measurement was performed over 20 kA peak current in the center of electrodes, in the vicinity of cathode, and outside electrodes. The electrode material tested was Fe. Measured Fe spectrum range was from 200 nm to 900 nm. Measurement result showed that over 90 percent of the charge states were FeII and the others were FeI and FeIII. The electron temperature was determined from the relative line intensity ratio methode of FeII system by assuming the local thermal equilibrium(LTE). The electron temperature at the center of electrodes was measured as 1.5 eV at 26 kA peak current. The electron temperature varied with its peak current. Intensity of spectrums is the highest in the vicinity of the cathode. Further we will also present study result of the diode phenomena in the TVS.

The occurrence of fires under transmission lines is responsible for a great number of power line outages. In this paper, the ac flashover voltages and the corona onset voltages of a needle-plane electrode gap of vertical arrangement in the presence of flame were investigated. We also observed the corona discharge current and variation of shapes in flame with increasing the applied voltages. We found that the corona onset voltages and the flashover voltages were drastically decreased with the position of flames and gap length of electrodes, and observed that the deflection or fluctuation phenomena in the shape of flames.

The occurrence of fires under transmission lines is responsible for a great number of power line outages. In this paper, the ac flashover voltages and the corona onset voltages of a model transmission line in the presence of flame were investigated. We found that the corona onset voltages and the flashover voltages were varied with the position of flames. Flashover voltages of vertical arranged electrodes with flame appeared to decrease 43[%] lower than those of same conditions with no flame.

This paper presents the induced ground potential rise distributions on several ground electrodes buried nearby. These experiments were conducted with the impulse currents as a function of the ground electrodes types and distances from the current injection point. The ground potential is significantly induced in the vicinity of ground electrodes, and the induced ground potential rises can caused unwanted erratic operation of electronic device.

In this paper, we investigated the breakdown characteristics of Ar, Kr and $N_2$ gas in pure states with pressure range of 58.8-137.3[kPa] under uniform and non-uniform fields, and the measured values are compared with those in Ar/$N_2$ gas mixtures. From these results, the breakdown voltages of $N_2$ gas in uniform field were increased about 4.8 and 4.4 times than those of Ar and Kr gas, respectively. Breakdown voltages of Ar/$N_2$ gas mixtures were decreased with decreasing the mixture ratio of $N_2$ gas. Breakdown voltages of Ar(70%)/$N_2$(30%) gas mixtures in the pressure of 101.3[kPa] (gap length : 3[mm]) were increased 1.9 times than those of pure Ar gas.

This paper simulated discharge progress and partial discharge using needle-plan electrodes system in $SF_6$, studied the distribution of frequency spectrum of the radiated electromagnetic waves using biconical antenna and spectrum analyzer. From results of this study, a method was introduced for measurement and analysis of the radiated electromagnetic waves in accordance with discharge progress in $SF_6$. Besides, according to the consideration of the mutual relation between frequency spectrum of the radiated electromagnetic waves and discharge progress, it was confirmed that detecting partial discharge and estimating discharge progress in $SF_6$ can be possible.

본 논문에서는 전기광학효과를 이용한 전압 계측기기의 개발을 위해 수행한 기초 연구에 대하여 기술하였다. 측정 시스템에 사용된 소자의 특성 및 입출력 특성에서 약 800 V까지의 출력특성이 측정오차 3% 내의 선형성을 나타내었으며, $\lambda$/4 Plate를 사용한 경우, 측정 정확도를 높일 수 있음을 확인하였다. 본 실험에서는 DKDP를 포켈스 소자로 사용하였으나, BGO와 같은 결정을 사용하면 수십 kV까지의 높은 전압을 직접 측정하는 것도 가능하다.

최근 전력설비의 절연을 위해 고분자 재질의 절연물이 광범위하게 사용되고 있다. 이러한 고분자 재료는 현재까지 주로 사용되어 온 세라믹 재질과는 달리 환경에 의한 열화를 동반하게 된다. 최근에 현장에 적용되기 시작한 고분자 재질의 절연물에 대한 장기 열화특성을 평가하기 위한 연구들이 다수 진행되고 있는 것도 이러한 이유 때문이다. 피뢰기의 경우에도 기존의 세라믹 애관을 고분자 재질의 애관으로 대체하기 시작하여 일부 제품들이 현장에서 우수한 특성을 보이는 것으로 보고되고 있으나 장기신뢰성에 대해서는 명확하지 않은 상태이다. 본 논문에서는 국내에서 제작되어 현장사용중인 폴리머 피뢰기를 발취하여 사용기간중 성능상의 변화를 분석하고 가속열화시험을 통해 성능의 변화를 관찰하고자 하였다.

Recently, ozone is utilized in various fields and its needs are expanding. In this paper, fluorescent discharge type ozonizer has been designed and manufactured. Ozone discharge and generation characteristics have been investigated in accordance with a sort of internal electrodes, output voltage of power supply. flow rate and discharge power. Air has been used as the supplied gas of the ozonizer.

In this paper, a co-axial cylinder type ozonizer using silent discharge known as an ozone generation was designed and fabricated. A cooling system was installed to investigate the characteristics of ozone generation in accordance with temperature change of the supplied gas known as an important factor. The characteristics of ozone generation were investigated in accordance with the existence of cooling system and the change of cooling temperature.

대기환경오염물질인 NO가스의 제거를 위하여 방전관을 채용한 3전극-2갭 방식의 새로운 형태의 오존발생기를 설계 제작하였다. 본 논문에서는 원료가스의 유량, 방전전력 및 오존발생기의 사용 개수 변화에 따른 방전특성과 오존생성특성을 연구검토하였으며, 오존발생기로부터 생성된 오존을 NO가스에 접촉시켰을 때 NO 제거특성이 우수하여 방전관형 오존발생기가 대기환경개선 설비로 적용가능함을 확인하였다.

The shorted-turn sensor for generator's field winding has been developed. The sensor, installed in the generator air-gap, senses the slot leakage flux of field winding and produces a voltage waveform proportional to the rate of change of the flux. For identification of reliability for sensor, a shorted-turn test was performed at the Seoinchon combined cycle power plant on gas turbine generator. This sensor will be used as a detecting of shorted-turn for generator's field winding.

EHV power cables can take any damage during shipping, transportation, handling, storage and installation. As the damage influences a reliability of the power cable system in the short and long periods, field tests have been required, for installers, to confirm the reliability of an installed system and, for utilities, to make sure the compatibility of an installed system. Of field tests, a HV withstand test for the cable insulation has been performed to check the soundness of the insulation. For EHV XLPE power cables, the test has been done by applying a specified d.c voltage till lately. But as some problems with the d.c test is emphasized and the equipment for the a.c test is improved, the a.c test is considered positively as an after-installation test. This paper describes the recent trends of the a and its recent application in the field.

This paper deals with the numerical estimation of the bubble behavior and the partial discharge(PD) initiation voltage basis of electric field calculation with the coaxial coil layer-to-cylindrical electrode system for the simulation of high temperature superconducting coils. The theoretical results of bubble behavior and the PD initiation voltages showed fairly good agreements with the experimental results.

The most of faults in gas insulation of power facilities are caused by partial discharge. Therefore we simulated partial discharge and measured the radiated electromagnetic wave emitted from partial discharge in the $SF_6$ gas by biconical antenna. This paper describes time delay characteristics of radiated electromagnetic waves with distance between antenna and discharge source.

In this experiment, an attempt to use the sludge pellets as catalyst for NO removal from simulated gas is experimentally investigated by using cylinder type reactor. An experimental investigation has been conducted for NO concentration of 50[ppm], 100[ppm], 200[ppm] balanced with air. a gas flow rate of 5[1/min]. Cylinder type reactor is at upstream of system for corona discharge and packed bed type reactor filled with sludge pellets ate put at downstream of Cylinder type reactor for catalystic effect. And AC voltage to discharge the gases was supplied. In the result, NO removal with magnetic field is higher than that without magnetic field, when packed-bed reactor with sludge pellet is installed at downstream of cylinder reactor NO, $NO_2$ removal rate increased and $O_3$ is not generated.

In this experiment, an attempt to use the sludge pellets as catalyst for NO removal from simulated gas is experimentally investigated by using $BaTiO_3$-sludge packed-bed reactor of plate-plate geometry. An experimental investigation has been conducted for NO concentration of 50[ppm] balanced with air, a gas flow rate of 5[1/min]. $BaTiO_3$ pellets are filled at upstream of reactor for corona discharge and sludge pellets are put at downstream of reactor for catalystic effect. The volume rate of sludge pellets to $BaTiO_3$ pellets is 50[%] and AC voltage to dischare the gases was supplied. In the result, when sludge pellets is seperated to $BaTiO_3$ by other reactor and AC voltage is supplied to $BaTiO_3$ and sludge pellets NO, $NO_2$ removal rate is higher. When gas temperature increase from room temperature to 100[$^{\circ}C$], NO removal is decreased while $NO_2$ concentration is independent on gas temperature. This result suggest that the removal mechanism of active oxyzen species and $NO_2$ in sludge is not absorption, but chemical reaction. Temperature of heating treatment is on sludge pellets increased, $NO_x$ removal rate is decrease. It is thought that organic compound is removed by heating treatment.

With the 4-MJ synthetic testing facilities completed, KERI can perform the circuit breaker testing up to 420 kV, 50 kA ratings. The short-line fault test is one of the necessary test items which are required for the circuit breaker, and in order to perform the short-line fault test KERI(Korea Electrotechnology Institute) has used the "new artificial line" which has small dimension and is easy to generate the saw-tooth wave. This paper describes the following items of the new artificial line. -Description of 4-kinds of artificial lines and determination of the circuit parameter of artificial line. -TRV characteristics of saw-tooth waves for each circuit. -KERI's artificial line.

A standard source was constructed, and then simulated its light distribution characteristics of the basic arrangements by shape, by angle, and by displacement. And it was constructed a light collecting holder of optical fiber lighting systems using RGB LED. As a result, we obtained the improving light collecting efficiency was improved 6.5 times with compared to existing systems.

Recently, Water Blocking Conductor have been used to basic specification at the EHV XLPE Cable, GlobalIy. The area of Middle East have need of severe test condition than existing the Water Penetration Test, specially. In this paper, compare with and investigate the Water Penetration Test's each standard, describes the development Water Blocking Conductor in the high water-pressure for the EDF HN 33-S-51's Water Penetration Test passing.

In this paper, the basic characteristics of flat fluorescent lamp using ultraviolet generated from gas discharge and powder type electro luminescent display using a phenomenon of the light emission caused by the electrical field applied to phosphor are studied. The lamp is a simple structure with insulator layer, phosphor layer, and gas gap. Current(displacement current + discharge current) in flat fluorescent lamp using.

This machine is a high-vacuum exhaust sealing device which makes the inside of PDP element in high vacuum state, blows inactive gases into it and finally seals it. This machine consists of vacuuming parts, heating parts and exhausting parts. Applying the energy saving technology, this machine improves the temperature uniformity of vacuuming and heating parts.

As a batch Type device, this machine is contrive to seal glass plates for plasma BLU (Back Light Unit) by indirect heating from electric heaters. In order to maintain the heating / cooling Chambers clean, this machine uses a muffle formation. The components of the machine are listed bellow.

At present the under ground power transmission systems have installed until 154KV XLPE power cable in Korea But, the large capacity underground power transmission systems have been required gradually with the increasing demand of electric power. Therefore, our company has developed 345KV XLPE cable. This paper describes the estimate details of the insulation thickness according to weibull plotting for 345KV XLPE power cable.

By comparing and analyzing the feature, brightness, chromaticity and uniformity of domestic LGPs and Japanese products, early home-manufacturing and stabilization in home-manufacturing are possible. By comparing and analyzing the distribution of brightness as sheets are varied, we can design an ideal sheet composition.

Because of its advantages such as more safe better electrical properties, lighter and easier to handle etc. than conventional ceramic materials, the development and application of composite insulator to the distribution and transmission system have been rapidly increased lately. In this paper, we reviewed performance evaluation on composite hollow insulator for extra high voltage based on IEC 61462 Technical Report 2, prospected to be published as international standards of Insulator for $SF_6$ GIS, Transformer, Arrestor etc, having been prepared by IEC technical committee 36 : insulator.

In order to obtain the useful data for quality control of the pole transformer and supply the stable electric power in distribution line, The evaluation of performance for low-loss pole transformer had been performed for new products and ones under operation for several years in distribution line. As the results, we found that the rate of fail were very high in gaskette, short-circuit strength and temperature-rise test, especially 48 percent in gaskette test.

For an efficient calculation of scattering matrix of planar transmission line with step discontinuity. Mode Matching Method combined with Vector Finite Element Method is adopted. Calculating effective widths are replaced with their respective equivalent planar waveguide corresponding to the microstrip width, Propagation Constant is calculated from the Vector finite element. Mode matching method is used for deriving scattering parameters.

광파이버 패브리페로 간섭계에서 동작영역을 넓히기 위해 공진기의 길이를 1mm보다 짧은 초소형 간섭계를 구성하고자 하였을 경우, 광출력의 위상변화에 대한 감도가 낮아 전달함수로부터 변화된 위상을 복원하는 과정이 까다로워진다. 이러한 신호복원 과정에는 대부분 신호잡음비를 높여주는 신호처리 수단을 포함하게 되므로 간섭계가 겪은 위상변화를 보다 높은 신뢰성으로 검출하고자 할 때 어떠한 신호처리 방법이 적절한가하는 선택의 문제가 발생된다. 이는 각각의 신호처리방법이 장단점을 가지므로 응용목적에 따른 trade-off가 필요하기 때문이다. 본 연구에서는 참조 간섭계와 센서 간섭계 간의 correlation으로부터 위상을 검출하여 시스템의 잡음을 common mode 잡음으로 처리할 수 있었으며, 디지털 신호처리기법을 응용하여 짧은 공진기로 구성된 센서 간섭계의 위상변화분을 보다 안정적으로 검출하게 되었다.

고리형 반도체-광섬유 레이저 공진기 안에 높은 복굴절률을 가지고 있는 편광 유지 광섬유 루프 거울을 삽입하여 새로운 구조의 다파장 발진 시스템을 제안하고 구현하였다. 이득 매질인 반도체 광 증폭기의 특성으로 인해 실온에서 파장 간격이 1 nm 이내인 22 개의 파장의 빛을 발진시킬 수 있었다.

본 논문에서는 주기적으로 홈을 새긴 V자 홈과 평판 사이에 광섬유를 놓고 압력을 인가함으로써 유도되는 파장가변 가능한 장주기 광섬유격자의 제작 및 특성에 대해서 살펴 보았다. 이러한 방식으로 제작된 장주기 광섬유격자의 투과특성 및 모드결합 특성은 기존의 장주기 광섬유격자와 유사한 특성을 보이면서도 모드결합이 일어나는 중심파장을 거의 180nm 이상으로 가변할 수 있었다.

A novel multi-section power divider configuration is proposed to obtain wide-band frequency performance up to microwave frequency region. Design procedures for the proposed microwave broadband power divider are composed of a planar multi-section three-ports hybrid and a waveguide transformer design procedures. The multi-section power divider is based on design theory of the optimum quarter-wave transformer. Furthermore, in order to obtain the broadband isolation performance between the two adjacent output ports, the odd mode equivalent circuit should be matched by using the lossy element such as resistor. The derived design formula for calculating these odd mode matching elements is based on the singly terminated filter design theory. The waveguide transformer section is designed to suppress the propagation of the higher order modes such as waveguide modes due to employing the metallic electric wall. Simulation and experiment show excellent performance of multi section power divider.

A new method of all optical packet header recognition scheme using a photorefractive hologram filter is presented. Wavelength encoded packet that has the header of a specific wavelength is assumed and the photorefractive filter can detect the wavelength. Concatenated electronics drives the optical switch to route the $\lambda$-encoded optical packet. The delay time at the switched signals are measured and compared with the original data stream.

The interference of electromagnetic waves in factory is increasing according with development of industrial society and many use of electrical machinery. Electromagnetic wave is defined as the electrical and magnetic field formed by electrical and electronic equipment used in daily lives, which indiscriminatingly affects the human health and operation of machinery. The electromagnetic spectrum ranges from the shorter wavelengths(including gamma and x-rays) to the longer wavelengths(including microwaves and broadcast radio waves). Radiation that is not absorbed or scattered in the atmosphere can reach and affect on the operation of machine. In this study, electromagnetic wave that is interfered to the machine and human is detected in factory, and decrease method of electromagnetic wave interference is studied.

A dual probe laser Doppler vibrometer (LDV) that has one laser source and provides two independent object beams has been developed for the first time. An electronic circuit that converts light signal to electronic signal has been also developed using digital phase locked loop(DPLL). It was found that this types of dual probe LDV can be used in differential mode and self-vibration compensation mode.

Asymmetrical parallel coupled lines are used in a number of circuits such as multi-band coupler and combline type band pass filter. Although graphical results and formulas are available for the design of coupled lines, the design procedure is hard to use, because even- and odd- mode impedances are always expressed in terms of the physical geometry. In this paper, we introduce a method to find design parameter using finite element analysis. By employing the capacitance obtained by FE analysis, design parameters for each lines are extracted. To show the validity of extracted design parameter for asymmetrical parallel coupled line, we have designed and simulated a planar type combline band pass filter.

광섬유는 저손실, 광대역의 전송특성을 가지며 세경(細徑), 경량등 많은 장점을 가지고 있지만 동케이블과 같이 파단점, 불연속점등의 장해점 탐색에 대한 어려움이 있다. 이러한 문제점을 해결하기 위하여 OTDR(Optical Time Domain Reflectometer)은 고감도, 고정도의 광센싱 기술, 극초단 광펄스 레이다 기술, 광다중화 센서 네트웍기술, 실시간 광신호처리 기술 등 정밀 광계측 및 신호처리기술을 적용하여 설치된 광섬유의 손실 정도를 측정하는 시스템으로 광섬유에 입사된 광의 산란 가운데 Rayleigh 산란에 의해서 생기는 후방산란광을 관측하여 광파이버의 파단점 탐색 및 손실측정이 가능하다. 최근 대부분의 유선통신망은 광섬유를 이용한 광통신방식으로 이루어지고 있으며 이러한 광섬유의 고장점을 찾기 위한 방법은 OTDR방식이 유일하다고 할 수 있다. 본 논문은 Rayleigh 후방산란에 의한 광학적 특성을 규명하고 이러한 특성을 이용하여 이용한 광섬유 유지보수용 계측시스템을 설계, 제작하고 실험한 결과에 대하여 설명하고 고찰하였다. 측정거리를 40Km까지 측정하도록 하였으며, 모니터상에서의 거리 분해능은 5m정도를 가지며 1310nm의 파장을 사용하였다.

본 논문에서는, 광통신에서 정보전송량을 극대화하기 위한 방법으로 WDM의 전송링크에 광 CDMA의 부호기와 복호기를 병합하여 WDM과 광 CDMA를 하이브리드 함으로써 전송용량을 극대화하는 방법을 제안하였다. 하이브리드 방법에는 초단펄스를 이용한 방법과 광지연 선로를 사용하는 방법이 있으나, 본 논문에서는 초단 펄스를 이용한 방법을 사용하여 적용하였다.

광전자실험에 사용되고있는 수동 광학소자로는 lense, mirror, grating, prism, polarizer 등 이 있다. 본 연구에서는 각 소자들에 대한 수학적 모델과 실질적 구조에 의한 수치 해석적 모델인 Split-step을 angular spectrum 방법을 구현하고 이를 이용한 실험적 결과를 이론치와 비교 분석하여 모델의 정확성을 분석하였다.

본 실험에서는 적색 유기 EL에서의 각 층별 두께비에 따른 발광특성을 조사하였다. 정공수송층으로 TPD(N,N'-dyphenyl-N-N'-bis(3-methyphenyl)-1, 1'-biphenyl-4,4'-diamine)를 사용하였으며, 전자수송층 및 적색 발광층으로는 DCM(4-(Dicyanomethyl)2-methy 1-6-(dimethylaminostyryl)-4H-pyrane)를 사용하여 정공 수송층과 전자수송층의 두께비를 변화시켰을 때, 발광특성을 조사하였다.

An Inverted-F antenna for the 2.4GHz application is designed and implemented. The antenna is implemented on the PCB board and installed in a vertical position. The 10dB characteristics are 2.4 to 2.48GHz in bandwidth which satisfies the bluetooth requirement and the whole impedance is matched. The feed-line on the PCB board is also calculated and implemented. And the measuring system is installed at the KITI in Kangwon Nat'l Univ. and applied to measured the antenna characteristics. The measured values show that this antenna is suitable for the commercial applications.

최근에 특정 주파수 대역에서 전자기파의 전파를 억제하는 주기 구조인 PBG(Photonic Band Gap) 구조에 대한 연구가 활발히 이루어지고 있다. 본 논문에서는 마이크로스트립 선로에서 사용될 수 있는 새로운 PBG cell을 제안하였다. 제안된 구조는 단일 cell 만으로도 대역저지 특성을 얻을 수 있고, cell의 치수를 조절하여 저지대역을 조절할 수 있다. 또한, 방사 효과 등으로 인한 손실을 고려하여 정확한 등가 모델링을 할 수 있다. 본 논문에서는 제안된 구조를 마이크로스트립 패치안테나의 하모닉 억제를 위해 사용하여 그 유용성을 입증하였다.

본 연구에서는 국내에서도 아직 초기단계 기술이라고 할 수 있는 간섭계를 이용한 주요 시설물(변전소등) 안전 감시 혹은 항만 감시 및 방어용 광섬유 격자 그물망 구현을 위한 광섬유 시스템 적용성을 연구한 것이다. 연구에서는 마흐젠더 간섭계의 구성에 비해 구성이 용이한 Sagnac간섭계를 구성 실험하였다. 이 간섭계의 성능 검증을 위하여 1550nm의 중심파장을 방사하는 레이저, 싱글모드 광섬유, 3${\times}$3 커플러 등의 광소자를 사용하였고, 광섬유의 길이의 변화를 주기 위하여 PZT 위상 변조기에 교류 전원을 인가하여 PZT 위상 변조기의 진동을 유도하였다. 또한, 전체 길이 약 180cm, 17${\times}$7, 철봉의 직경 6m의 철망 구조물을 제작후, 센서 부분의 역할을 담당한 광섬유 케이블을 일정한 간격으로 철망 구조물에 케이블 타이로 고정하였다. 철망 구조물에서 발생할 수 있는 각종 외부 가진에 대해, 철망 구조물에 가속도계를 설치하여, Sagnac 간섭계에서의 광 간섭 신호와 가속도계의 신호를 비교 검증 하였다. 본 실험결과를 통하여 광섬유 펜스는 주요 시설물(변전소등) 안전 감시 혹은 항만 감시 및 방어용 경보 시스템에 적합하다고 판단된다.

최근 배전계통에서는 전력공급 신뢰도 향상을 위해서 평상시 및 사고시의 전압/전류를 신속하고, 정확하게 계측할 수 있는 광계측 방식의 적용이 적극적으로 진행되고 있다. 본 논문은 이러한 것을 배경으로 하여 배전용 광 CT 및 PT의 국산화 모델의 선정, 시제품 제작 및 특성시험의 결과에 대해서 기술하였다.

DNA 센서의 중요한 역할 중의 하나는 염기서열을 분석함으로써 유전적인 질병이나 돌연변이를 찾아낸다는 점이다. 염기서열 분석법으로 질량, 광학, 전기 화학적 측정법 등이 있는데, 그 중 전기 화학적 측정방법이 타 방법에 비해 간편하고 비용도 저렴해서 전망이 매우 밝다. 전기 화학적 측정을 위해서는 전극의 표면 처리 공정과 전극 표면에서의 DNA immobilization, hybridization 공정 및 전기적 신호를 발생시키는 intercalator, 그리고 전기적 신호 검출을 위한 측정 장비가 필요하다. 본 논문에서는 전극의 표면 처리 물질로서 2-mercaptoethanol을 사용했고 double strand DNA의 intercalator로써 methylene blue를 사용했으며, methylene blue의 환원 전류값을 측정하여 double strand DNA를 bare Au 또는 single strand DNA와 구분할 수 있었다. 이러한 연구 결과를 토대로 하여 전기 화학적 신호 검출을 이용한 DNA 센서의 가능성과 개발 방향을 제시하고자 한다.

This paper presents an implantable telemetry LC resonance-type pressure sensor to measure the cerebral ventricle pressure. The sensor consists of an inductor and a capacitor. The LC resonant circuit consists of the sensor and an external antenna coil that are coupled magnetically. The resonance frequency of the circuit decreases as the applied pressure increases the capacitance of the sensor. The sensor is designed in consideration of the biocompatibility and long lifetime for continuous monitoring of the ventricle pressure. The sensor is simple to fabricate and small in comparison with others reported previously. The inductor is fabricated by electroplating and the variable capacitor is constructed with a flexible p+ diaphragm. Also, the deflection of the diaphragm, the variation of the capacitance and the resonance frequency are analyzed and calculated.

Glaucoma is an eye disease which is caused by abnormal high lOP (Intra Ocular Pressure). High lOP is caused by the aqueous humor which is produced consistently but not drained due to malfunction of the trabecular system which has a role of draining the aqueous humor into the venous system. Currently, there are some methods to treat glaucoma, Among these, the use of implants is increasing in these days due to many problems In other methods. However, conventional implants are passive implants and have critical disadvantage. Therefore, it is needed to develop an active implant which is composed of a valve actuator, pressure sensor, controller, and power supply. In this paper, we make experiment with the fabricated valve actuator in In-vitro experiment, and estimate the in-vivo result using the experimental result and investigate the possibility of the fabricated valve.

In order to fabricate the stable conductive polymer actuators which are operated in air. Nafion with mixture of LiCl has been used as solid polymer electrolyte material. Based on these materials, beam type and sandwich type actuators have been fabricated and mechanical properties are measured. This kind of all-solid-polymer actuator can be used for practical applications.

We manufactured a micro CPL by LlGA process, a new conceptual ultra-fine and precise forming method, using X-ray lithography process. We fabricated a BN X-ray mask having properties of good X-ray transmittance and large mechanical strength. Micro CPL was manufactured by dividing into an upper plate and a low plate. Each of plates was bonded by Ag paste screen printing. The upper plate was fabricated on glass wafer to observe flow and phase transformation of cooling solution. The lower plate was manufactured by Cu electroplating for good heat transmission. Precision of inner Parts, micro pin and micro channel, of manufactured micro CPL is under ${\pm}2{\mu}m$.

In this study, we fabricated Al mirror driven by electromagnetic force. Because the mirror has Ni staple joint, it reduces the deflection angle of torsion spring for the maximum deflection of mirror. Therefore the magnetic field for maximum deflection can be reduced, By additional electrostatic force, the deflection angle of mirror plate can be increased to $90^{\circ}$. The fabricated mirror is actuated by electromagnetic force of a simple solenoid. The maximum deflection angle by magnetic field is about $86^{\circ}$ with $1.2{\times}10^4$ A/m.

금속 재질의 MEMS 구조물의 모양을 폴리머에 전사하는 micromolding 과정에서 금속 구조물과 폴리머 사이를 분리 (demolding)시킬 때 금속 구조물과 폴리머 기판 사이에 분리를 방해하는 응착 (Adhesion) 문제가 발생한다. 이러한 응착 문제를 줄이고자 표면 에너지가 낮은 Self-Assembled Monolayer(SAM) coating을 금속(Ni) 표면에 시도하였다. SAM coating 막의 형성 여부와 응착력 (Adhesion force) 값을 구하기 위해 각각 XPS(X-ray photoelectron spectroscopy)와 AFM(Atomic force microscopy)을 이용하여 측정하였고 측정 결과 Ni 표면에 SAM이 형성되었음을 XPS로부터 알 수 있었고 SAM coating된 Ni 시편에서 더 낮은 응착력값을 보여 주었다.

This paper described on the fabrication of microstructures by DRIE(Deep Reactive Ion Etching). SOI(Si-on-insulator) electric devices with buried cavities are fabricated by SDB technology and electrochemical etch-stop. The cavity was fabricated the upper handling wafer by Si anisotropic etch technique. SDB process was performed to seal the fabricated cavity under vacuum condition at -750 mm Hg. In the SDB process, captured air and moisture inside of the cavities were removed by making channels towards outside. After annealing(1000$^{\circ}C$, 60 min.), the SDB SOI structure was thinned by electrochemical etch-stop. Finally, it was fabricated microstructures by DRIE as well as a accurate thickness control and a good flatness.

In this paper, novel release technique using wet etch is proposed. The results of this technique and the results of SAMs (Self-Assembled monolayers) coated after release using this technique are compared. Fabricated structure have 100 um in width and experimental length is from 100 um to 1 mm. Thickness of aluminum sacrificial layer is 2 um and structure thickness is 2.5 um. Cantilevers and bridges are fabricated with electroplated gold and silicon nitride deposited on substrate. An aluminium sacrificial layer was evaporated thermally and removed in various wet etching solutions. Detachment length of cantilever is 200 um and detachment length of bridge is 1 mm after isooctane rinsing. And the SAMs coating condition which is appropriate for gold and nitride are studied respectively.

An offset problem caused by the static parasitic capacitors is analyzed and then some techniques to reduce their effect on the capacitive position sensor are presented. Also new offset compensation technique is proposed that by adjusting the magnitudes of the modulating signals independently, the charge imbalance between electrodes caused by the parasitic capacitors is eliminated without sensor gain variation. Simulation results are given to validate the proposed compensation technique.

본 논문에서는 3차원 feed horn 안테나를 볼로미터에 결합함으로써 감지도(Detectivity)를 향상시킨 비가시광 영상 감지 소자를 제안하였다. Feed horn 안테나의 우수한 지향성(Directivity)를 통해서 주위의 잡음 성분을 제거함으로써 감지도의 향상을 확인할 수 있었다. 안테나와 볼로미터와의 결합 손실을 줄이기 위해서 볼로미터의 흡수층의 모양을 원형의 형태로 하였으며 크기도 안테나 폭과 일치를 시켰다. 또한 열적 고립 구조를 만들기 위한 지지 다리의 모양도 원형의 형태로 하여서 전체 길이를 증가 시켰으며 이로 인해 열전도도(Thermal conductance)를 $4.65{\times}10^{-8}$[W/K]까지 낮출 수 있었 다. 설계된 소자의 감지도는 $2.37{\times}10^{9}$[$cm\sqrt{Hz}/W$]을 나타내었으며 안테나 결합을 통한 감지도의 향상을 확인 할 수 있었다. 볼로미터의 제작은 MEMS 기술을 이용한 표면미세가공(Surface micromachining)법으로 열적 고립 구조체를 제작할 수 있으며 3차원 feed horn안테나는 SU-8이라는 음성 감광제를 경사회전노광시켜서 제작할 수 있다.

본 논문은 마이크로머시닝 기술을 응용하여 다공질 실리콘 다이어프램을 제작하여 air, $N_2$, Ar 분위기에서 유리로 패키징하였다. 유리로 패키징된 소자들과 유리 패키징을 하지 않는 소자를 시간 경과에 따른 다공질 실리콘의 PL(Photoluminescence) 스펙트럼 (peak wavelength, intensity)과 저항 변화를 측정하였다. 또한, 패키징 분위기에 따른 다공질 실리콘의 aging 효과를 서로 비교하여 다공질 실리콘 다이어프램을 이용한 PIN 구조의 소자를 광센서로써 응용 가능성을 살펴보았다.

본 논문에서는 다공질 실리콘에 대한 에탄올과 메탄을 가스 감지 특성을 측정하고 전기 전도도의 변화를 고찰하였다. 우선 HF와 에탄올의 혼합 용액내에서 n-type의 웨이퍼에 일정 전압을 인가하여 다공질 실리콘을 형성한다. 다공질 실리콘은 수직한 방향으로 $55{\sim}60{\mu}m$ 두께로 균일하게 형성되었다. 다공질 실리콘을 이용하여 소자를 제작하고 에탄올과 메탄올 가스를 주입하여 전류-전압 특성을 측정하였다. 기존의 다공질 실리콘 에탄올 센서와는 달리 turn-on 시 센서에 흐르는 전류가 빠른 시간내에 일정한 값으로 도달하였고 turn-off시에도 같은 결과를 보였다. 다공질 실리콘 표면에 흡착된 에탄올과 메탄올 가스는 전류의 흐름을 방해하는 surface charge를 스크린하여 전기 전도도를 증가시킨다. 또한 흡착된 가스가 dangling bonds를 passivation하여 전류를 증가시키는 것으로 생각된다.

본 논문은 마이크로머시닝 기술을 이용하여 lift-off 공정으로 패턴닝 한 후 TMAH (Tetramethylammonium Hydroxide) 용액으로 $5{\sim}100{\mu}m$ 두께의 실리콘 다이어프램을 제작하였다. Pt/Ti 박막을 HF 전해질의 mask 물질로 사용하여 HF 용액 내에서 전기화학적 방법으로 정전압을 인가, 다이어프램 영역에 다공질 실리콘을 성장시켜 관통하였다. 140$^{\circ}C$의 질소 분위기에서 $10{\sim}15{\mu}m$두께의 LDPE(Low Density Poly Ethylene) 필름을 물리적으로 다이어프램 영역에 코팅하고 $K_2CO_3$ 용액내에서 ${CO_3}^{2-}$ 이온의 barrier에 의한 전류의 감소를 전기화학적인 분석방법에 의하여 측정하였다. 일정 전압하에서 이온 농도에 기인하는 다공질 실리콘과 LDPE 표면에서 Barrier의 두께에 따른 저항의 증가를 전극으로 감지하여 농도-전류의 특성을 측정하고 이것을 기준으로 하여 미지농도의 $K_2CO_3$ 용액내의 ${CO_3}^{2-}$ 이온 농도를 측정하였다.

전위차 측정형 바이오 센서는 기준전극에 대한 센서 전극의 전기화학적 전위를 정확하게 측정하여야 하므로 기준전극의 안정성이 매우 중요하다. 기준전극의 전위는 전해질 용액 내의 염소 음이온 농도에 영향을 받으나 다행히도 혈액 내의 염소 음이온 농도는 거의 변화가 없으므로 혈액 속에서의 은/염화은 기준전극의 전위도 거의 변화가 없다. 본 연구에서는, 사진석판 (Photolithography) 공정을 이용하여 실리콘 표면 및 다공질 실리콘 표면에 은/염화은 박막 기준전극을 제작하고 시료 용액에서의 drift, 안정성, 재현성 등에 대한 특성을 고찰하였고, SEM, AES, EDX 스펙트럼 등을 이용하여 전극의 표면을 분석하였다. 시료 용액의 염소 음이온 농도를 $10^{-4}$M에서 1M까지 변화시켜가며 기준 전극의 전위를 측정한 결과 약 50mV/pCl의 기울기를 얻었으며 이것은 Nernst식을 잘 따르는 결과이다.

3D Feed Horn Shape MEMS Antenna Array는 적외선 이미지 소자 또는 Tera hertz band 등에서 많은 응용을 할 수 있는 장점을 가진 MEMS 구조체 이다. 하지만 일반적인 MEMS 공정을 이용해서 3D Feed Horn Shape MEMS antenna array를 구현하기는 적합하지 않았다. 본 논문에서는 마스크와 웨이퍼가 일체 된 형태의 경사된 척이 초 저속으로 회전하면서 노광을 할 수 있는 새로운 방식과 미러 반사구조를 이용해서 평행광을 얻을수 있는 노광장치 (MRPBI : Mirror Reflected Parallel Beam Illuminator) System제작방법을 제안하였다. 3D Feed Horn Shape MEMS Antenna의 구조적인 high apect ratio의 특성에 의해서 SU-8과 PMER Negative Photo resist를 이용한 기본적인 실험을 통해 3D 구조체의 구현 가능성을 증명하였다. 또한 Microbolometer의 성능향상을 위한 이론적인 3D MEMS Antenna Model들을 HFSS(High Frequency Structure Simulator)을 이용해서 그 최적구조를 제안하고 3D MEMS Antenna Gain 값을 비교 분석하였다.

초소형 히트파이프는 고집적 반도체 소자에서 발생되는 열을 효과적으로 소산하기 위한 열교환 장치이다. 초소형 히트파이프는 작동유체가 상 변화 잠열을 이용한 칩 레벨의 냉각 장치이다. 작동유체는 진공으로 밀봉된 공간내에서 외부 동력 없이 모세관력에 의하여 이동한다. 본 논문에서는 실리콘보다 열전도도가 우수하여 발생되는 열을 더욱 빠르게 소산시킬 수 있는 구리 모재의 초소형 히트파이프를 제작한다. 특히, 모세관력은 히트파이프의 성능을 좌우하는 요소이다. 모세관력 향상을 위해서 구리 전기도금으로 이용하여 홈(groove)부분을 제작한다. 윅(wick) 제작, 구리판 접합, 작동유체 충전등으로 초소형 히트파이프를 제작한 후, 성능 실험한 결과를 보여준다.

In this work, an array of resistance temperature detector(RTD) was fabricated inside the microchannel in order to investigate in-situ flow characteristics. A rectangular straight microchannel, integrated with RTD's for temperature sensing and a heat source for generating the temperature gradient along the channel. were fabricated with the dimension of $200{\mu}m(W){\times}{\mu}m(D){\times}$48mm(L), while RTD measured precise temperatures at the inside-channel wall. 4" $525{\pm}25{\mu}m$ thick P-type <100> Si wafer was used as a substrate. For the fabrication of RTDs. 5300$\AA$ thick Pt/Ti layer was sputtered on a Pyrex glass wafer. Finally, glass wafer was bonded with Si wafer by anodic bonding, therefore RTD was located inside the microchannel. The temperature distribution inside the fabricated microchannel was obtained from 4 point probe measurements and Dl water is used as a working fluid. Temperature distribution inside the microchannel was measured as a function of mass flow rate and heat flux. As a result, precise temperatures inside the microchannel could be obtained. In conclusion, this novel temperature distribution measurement system will be very useful to the accurate analysis of the flow characteristics in the microchannel.

A novel wet release process ($\mu$ CARP - Micro Channel Assisted Release Process) for releasing an extreme large-area plate structure without etching hole is proposed and experimented. Etching holes in conventional process reduce a effective area and degrade an optical characteristics by a diffraction. In addition, as the area of a released structure increases, the stietion becomes more serious. The proposed process resolves these problems by the introduction of a micro fluidic channel beneath the structure which will be released. In this paper, a 5 mm${\times}$5mm-single crystal silicon plate structure was released by the proposed $\mu$CARP without etch holes on the structure. The variation in etching time with respect to the of the introduced micro channel is also examined. This process is expected to be beneficial for the actuator of a nano-scale data storage and the scanning mirror.