최근 생활수준의 향상과 정보통신 산업의 급속한 발전으로 인하여 전세계적으로 전력품질에 대한 관심이 높아져, 각종 전력품질 개선장치로부터 최적 공급시스템에 이르기까지 다양한 각도에서 전력품질을 향상하기 위한 연구개발이 수행되고 있으며, 특히 정보통신기기 및 정밀제어기기 등의 보급증가로 전압품질에 대한 관심이 높아져가고 있다. 지금까지 배전계통의 전압관리는 배 전용변전소 ULTC(Under Load Tap Changer)와 고압배전선로의 주상변압기에 의해 조정되어 왔으며 최근에 고압배전선로의 전압강하가 5%를 초과하는 선로에 대한 효율적 전압관리를 위해 선로전압조정장치(SVR- Step Voltage Regulator)가 도입되고 있다. 그러나 배 전용변전소와 고압배전선로의 선로전압 조정장치가 서로 독립적으로 운용되고 있기 때문에 선로전압조정장치의 효율성이 떨어지고 있는 실정이다. 그러므로 본 논문에서는 배 전용변전소와 선로전압조정장치의 ULTC 송출전압의 최적 전압조정을 위한 협조운용 방안을 제시하고자 한다.

This paper proposes a modified current differential relay for Y-$\Delta$ transformer protection. The relay uses the same restraining current as a conventional relay, but the differential current is modified to compensate for the effects of the exciting current. A method to estimate the circulating component of the delta winding current is proposed. To cope with the remanent flux, before saturation, the core-loss current is calculated and used to modify the measured differential current. When the core then enters saturation, the initial value of the flux is obtained by inserting the modified differential current at the start of saturation into the magnetization cure. Thereafter, the core flux is then derived and used in conjunction with the magnetization curve to calculate the magnetizing current. A modified differential current is then derived that compensates for the core-loss and magnetizing currents. The performance of the proposed differential relay was compared against a conventional differential relay. Test results indicate that the modified relay remained stable during severe magnetic inrush and over-excitation because the exciting current was successfully compensated. The relay correctly discriminates magnetic inrush and over-excitation from an internal fault and is not affected by the level of remanent flux.

A DC railway system has low feeder voltage, The remote fault current can be smaller than the current of load starting. So it is important to discriminate between the small fault current and the load starting current. The load starting current increases step by step but the fault current increases all at once. As for the load starting current, the time constant of load current at each step is much smaller than that of the fault current. To detect faults in DC railway systems, an algorithm using the time constant calculated by the method of least squares was presented. But, It have a weakness about harmonic to calculate time constant. So in this paper, new protection algorithm for DC railway systems using estimation of time constant based on fourier transform was presented.

This paper presents a modeling and simulation of a grid-connected wind turbine generation system with respect to wind variations and three-phase fault in the system. It describes the modeling of the wind turbine system including the drive train model, induction generator model, and grid-interface model on MATLAB/Simulink. Case studies demonstrate that the pitch angle control is carried out to achieve maximum power extraction for wind speed variations and the duration of a fault on the system influences on the output of the wind turbine generator.

The purpose of this paper is to explain the techniques of the data verification module achieved while developing a transient stability program which is suitable to korean power system. It concentrates on the concrete explanation about modeling of the dynamic models and the method of the data verification. This proposed module enhances the performance of the developing program. This developing module has been tested with the KEPCO system, and the simulation results obtained from the program are compared to those of commercial programs.

This paper proposes a new algorithm of underground cable fault location based on the analysis of distributed parameter circuit. The proposed method firstly makes voltage and current equations for each of cores and sheathes respectively, and then establishes an equation of the fault distance according to the analysis of the fault conditions. Finally the solution of this equation is calculated by Newton-Raphson iteration method. The effectiveness of this proposed algorithm has been proven through PSCAD/EMTDC simulations.

This paper proposes a new configuration of 36-pulse voltage source converter which consists of two 6-pulse bridges and a pulse-interleaving auxiliary circuit. The system topology of proposed converter was derived to increase the pulse number of converter output voltage without increasing the number of 6-pulse bridges. The gate pulse generation was analyzed using the theoretical approach of multi-pulse switching converter. The operational feasibility of proposed system was verified by computer simulations with PSCAD/TMTDC software and experimental works with 3kVA hardware prototype. The proposed converter can be widely used for the uninterruptible power supply, the power quality compensator, and the distributed power generation, such as solar and fuel fell power system.

In many countries, including Korea, in order to transmit the more electric power, the higher transmission line voltage is inevitable. So, a rapid reclosing scheme is important for UHV transmission lines to ensure requirements for high reliability of main lines. But, because of the high voltage and long span of UHV lines, the secondary arc current flows across the fault point even after the interruption of the fault current. i.e. A critical aspect of reclosing operation is the extinction of the secondary arc since it must extinguish before successful reclosure can occur. In Korea transmission lines, it is scheduled to energize 765kV single transmission line(79km) between Sin-Ansung S/S and Sin-Gapyeong S/S at June 2006. Therefore this paper analyzes characteristics of the secondary arc extinction on 765kV single transmission line using EMTP. Simulation results shows that the average value of the secondary arc is $30A_{rms}$ and the auto-extinction time of it is longer at closer point to Sin-Gapyeong S/S.

주변압기실에 Water Mist 소화설비의 적용을 위하여 과거 화재사례 분석, 변압기의 형태, 변압기실의 구조 등을 검토하여 3가지 화재유형을 상정하였고, 발생 가능한 화재규모 및 종류를 검토하여 소화성능 평가를 위한 6가지 화재 시나리오를 제시하고 이를 검증하기 위한 모의실험을 수행하였다. 본 연구를 통하여 주변압기실에 적용 가능한 최적의 Water Mist 소화설비의 시험기준을 정립하였으며, 향후 본 시험기준에 의한 전력공급용 주변압기실 Water Mist 소화설비가 화재에 의한 대형 재난을 예방함과 동시에 안정적인 전력공급에 이바지할 것으로 기대된다.

최근 전력수용의 증가와 산업설비의 첨단화로 안정적인 전력공급을 위한 예방진단의 필요성이 커지고 있다. 이 논문은 기존 전력설비 진단 방법과는 다른 적외선 열화상을 이용한 방법을 설명하고 전력설비 중 변압기의 진단에 대한 판단 기준을 설명한다.

This paper analysed the induced current density inside human body of hot-line worker for 765kV double circuit transmission line according to locations of human body Human was modelled by several organs, which included brain, heart, lungs, liver and intestines. We applied the 3 dimensional boundary element method to calculate induced electric fields.

In this paper, we are going to propose the new algorithms to detect, classify, discriminate the transient and the reflected signal from noise and thus discriminate the fault section and locale the fault accurately on underground power cable system. Actually, at this system, it's very difficult to discriminate the transient because of the reflected signal including many noises. Therefore, how to solve the noise interference is a big problem. In this paper, authors present a solution based on multiple scales correlation of the transient using stationary wavelet transform. It's simple, quick and straightforward. For applying all algorithms, we just use the signal captured in single end.

Arc-furnace is one of the large loads in the electric power system. When the arc-furnace operates, it may cause a bus voltage fluctuation in the power system, because it consumes a lot of reactive power. In this paper, we simulated this phenomenon by using a PSAF program with on-site measured arc-furnace load for different amount of cutailment load.

Transmission line outage is influenced by several weather factors: wind, rain snow, temperature, cloud and humidity. And most power system reliability studies assume a failure rate. It can be calculated by transmission line outage data and weather data. Also weather is divided into normal weather and adverse weather by failure rate analysis. The effect of failure rate is discussed with both normal weather and adverse weather. It can be used in effective information about system operation and planing.

The recent advancement in the power electronic technique has increased the use of induction motor fed by inverter using high-frequency switching devices. Also the tendency is toward larger size and higher voltage. Therefore, The IGBT (Insulated-Gate Bipolar Transistor) that is high switching frequency element has been using increase. But, The switching surge voltage was occurred by high switching frequency of inverter has appeared a voltage doubling in the motor input terminal due to mismatching of cable characteristic impedance and motor characteristic impedance. Actually, The Switching surge voltage became the major cause to occur the insulation failure by serious voltage stress in the stator winding of induction motor. The short during rise time of switching surge and cable length is increased, the maximum transient voltage seen at the motor terminals increases. In this paper, Analyzed switching surge transient voltage of power cable pulling is used EMTP(Electromagnetic Transient Program) at the induction motor terminal and in cable.

The current source HVDC using thyristor valves requires the reactive power compensator, the increasement of short circuit ratio(SCR) by AC source, and the harmonic filter in power transmission. The voltage source HVDC that controls active power and reactive power independently can minimize the requirements and also can be used as a reactive power source without additional reactive power compensators. In this paper, the solution of supplying active power using direct current transmission and compensating additional reactive power at the heavy load zone in metropolitan area is proposed and verified by simulations.

This paper presents a method to predict failure probability related to aging. To calculate failure probability, the Weibull distribution is used due to age-related reliability. The Weibull distribution has shape and scale parameters. Each estimated parameter is obtained from Data Analytic Method (Type II Censoring) which is relatively simpler and faster than the traditional calculation ways for estimating parameters. Also, this paper shows the calculation procedures of a probabilistic failure prediction through a stochastic data analysis. Consequently, the proposed methods would be likely to permit that the new deregulated environment forces utilities to reduce overall costs while maintaining an age-related reliability index.

Nowadays there are many kinds of large scale loads and they make the power quality deteriorated. As the uses of nonlinear loads increase, there are the influences on the other kinds of loads (mainly light loads) in the same distribution system. Especially the voltage variation by the loads which draw the large and instantaneous currents can cause the appreciable light flicker. This is called the voltage flicker or, briefly, the flicker. This paper deals with the digital and time domain algorithm of measuring flicker based on IEC 61000-4-15 and the real time measurement of flicker through the proposed power quality monitoring system.

상정사고 해석의 경우 수많은 상정사고를 실시간에 해석하기 위하여 전력조류계산 결과로 얻어진 Jacobian의 역행렬이 포함하고 있는 민감도 정보를 이용하는 경우가 많다. 이 경우 각종 상정사고 후의 각 모선전압과 전압의 위상각과 같은 상태변수를 선형적으로 신속히 계산할 수 있는 장점이 있는 반면에 송전선로 고장과 같이 계통구성이 변하는 상정사고의 경우에는 계산결과 얻어지는 상태변수 값들의 오차가 커져 상정사고 해석 결과가 부정확해지는 문제점이 있다. 이때 보다 정확한 상태변수 값들을 계산하기 위해서는 탈락한 송전선로를 반영하여 Jacobian을 재구성하고 그 역행렬을 계산하여야한다. 본 논문에서는 특히 민감도를 이용한 상태변수 값의 선형 계산에서 오차가 커지는 문제점이 있는 송전선로 고장의 경우 계통의 구조 변화를 반영한 Jacobian의 역행렬을 별도로 계산하지 않고 기본 케이스 Jacobian의 역행렬을 그대로 이용하여 간단히 구하는 방법을 제시함으로서 보다 빠르고 정확한 상정사고 해석을 할 수 있는 기법에 대해 제안하였다. 제안한 방법은 뉴잉글랜드 39 모선 계통에 적용하여 그 효과를 입증하였다.

This paper suggests the power system reliability evaluation fur transmission lines planning in composite power systems. In recent the importance and necessity of some studies on reliability evaluation of grid comes from the recent black-out accidents occurred in the world. Since probabilistic criterion can reflect recognize the probabilistic nature of system components, the application of probabilistic criterion has received a lot of attention. This paper introduces features and operation modes of the Transmission Reliability Evaluation fur Large-Scale Systems(TRELSS) Version 6.2, a program made in EPRI, for assessing reliability indices of composite power system. The characteristics of the TRELSS program are illustrated by the case studies using the KEPCO system.

In the past, TR-cost was collected the combination of energy cost. When power market is restructured. TR-cost is collected the separated form of loss-cost, congestion-cost and maintenance-cost. One of thorn, loss-cost is computed by using TR loss-factor. We need correct and fair standards of loss factor to offer economical signal and to protect against confusions of investment and bidding. Therefore, we propose the method of minimizing system loss-cost that is based on fair and correct loss-factor.

This paper presents the development method of educational simulator for the load flow. The developed simulator can be made the students to model, analysis of power systems by drawing the system and performing the load flow by themselves under window environment. For the effective education of load flow, we have introduced the avatar which is the object to explain the load flow to the students. Also, The simulator has developed by using the language based on XML(Extended Markabel Language). Therefore, we determine that this simulator is useful to educate the load flow and easily to expand the other application program.

Load forecasting is essential in order to supply electrical energy stably and economically in power systems. ANNs have flexibility to predict a nonlinear feature of load profiles. In this paper, we selected just the necessary input variables used in the paper(2) which is based on the phase-space embedding of a load time-series and reviewing others. So only 5 input variables were selected to forecast for spring, fall and winter season and another input considering temperature sensitivity is added during the summer season. The training cases are also selected from all previous data composed training cases of a 7-day, 14-day and 30-day period. Finally, we selected the training case of a 7-day period because it can be used in STLF without sacrificing the accuracy of the forecast. This allows more compact ANNs, smaller training cases. Consequently, test results show that compact neural networks can be forecasted without sacrificing the accuracy.

This paper discusses the development of the educational simulator for the electricity spot market in korea. The interaction between lectures and users can be much enhanced via the web-based programs which result in the student's teaming effectiveness on an electricity spot market. However the difficulties for developing web-based application programs are that there can be the numerous unspecified users to access the application programs. To overcome the aforementioned multi-users problem and to develope the educational simulator, we have revised the system architecture, the modeling of application programs, and database which efficiently and effectively manages the complex data sets related to an electricity spot market. The developed application program is composed of the physical three tiers where the middle tier is logically divided into two kinds of application programs. The divided application programs are interconnected by using the Web-service based on XML (Extended Markup Technology) and HTTP (Hyper Text Transfer Protocol) which make it possible the distributed computing technology.

As the circumstance of the traditional system is changed according to power system deregulation, the simulation tool which should reflect market code providing market operating mechanism is needed to analyze an electricity market. This paper presents the development of Electricity Market Price Simulator for short term(EMPS) that is designed to imitate the Korean electricity market. The EMPS is developed in VB.NET and is composed if three functions that consist of calculating SMP for CBP market, MCP for TWBF market and LMP for LMP-market. To evidence the features and the performance of EMPS, a small two way bidding market with 12-bus system, one way bidding market for generator competition and LMP market with 5-bus system will be presented for the electricity market simulations using EMPS.

Transmission congestion is one of the Key factors to local market power in competitive electricity markets. Withholding is a one of the methods exercise the market power. This paper presents an alternative methodology in market power under transmission congestion and withholding. The proposed methodology was demonstrated with the Optimal Power Flow(OPF). Case study is fulfilled by GAMS simulation.

In competitive electricity markets, the System Operator (SO) coordinates the overall maintenance schedules whenever the collective maintenance schedule reported to SO by Gencos in the pool does not satisfy the specified operating criteria, such as system reliability or supply adequacy. In this paper, we divide maintenance schedule problem into master-problem and sub-problem. Master-problem is schedule coordination and sub-problem is DC-optimal power flow. If sub-problem is infeasible, we use the algorithm of modifying operating criteria of master-problem.

This paper provides calculation of nodal price using voltage variables on Power System Operation. In this method we show deriving Shadow Price from state variables in Optimal condition. and we presented a new spliting method using voltage variables for zonal price. The proposed method is applied to IEEE-30 and results shows the effectiveness of the method.

This year korea power system had recorded highest peak load for 6 times and finally it made new peak load 51,264MW at July 29th 3:00 PM. The new peak load is increased 8.2% from the last year peak load 47,385MW and korea power system entered 50,000MW load era. The Korea Power Exchange (KPX) snapped power system data at the peak load time using state estimation function in the EMS. And authors converted the power system data at peak load to PSS/E power flow format. Using this PSS/E peak load power flow data, this paper explains demand analysis result shun capacitor operation, voltage distribution at the peak load. And the paper shows the simulation result of 2 contingency analysis using the snapped PSS/E peak load data.

송전선로 주변의 전자계 노출은 소아들의 암 발생/사망과 성인의 암 등 여러 가지 질병 발생 가능성이 항상 있으므로 전자계 노출을 장기간 계속적으로 받고 있는 환경을 관찰하는 것이 가장 중요하다. 따라서 본 연구에서는 이에 대한 연구기반을 형성하기 위해 송전 선로의 모델과 현장 실측을 통해 송전선로 자계치를 계산하여 시뮬레이션 하고자한다. 시뮬레이션을 통해 산출된 자계치를 이용하여 최근 효과적인 자계 저감책으로 보고되고 있는 수동루프에 의한 자계저감효과를 검토하고자 한다. 입력된 데이터는 765kV 실 송전선로를 모델로 사용하였으며, 자계의 계산 및 수동 루프에 의한 자계 저감 효과를 알아보기 위해서 미국 EPRI에서 개발한 자계 계산 전용 프로그램인 EMF Modeler를 이용하였다. 먼저 송전선로에 의해 발생되는 자계의 원리를 서술하였으며, 수동 루프를 통한 자계 감소 정도를 수식으로 유도하였고, EMF Modeler를 통하여 송전선 주변의 자계 분포 및 수동루프에 의한 자계 저감 효과를 각각 확인하였다.

This paper presents a methodology which can make alternatives of distribution system, and can calculate reliability costs, harmonics costs, and construction costs. And by using total cost of the system, decision maker can select the most economic and reasonable alternative. As a result, not only we can decide most economical and reasonable result, but we can get proper reliability and harmonics level. The usefulness of the method is verified by applying it to the test system.

Recently, power system is getting larger and more complex. When the complex power system has a problem, it is very difficult even for the experts to find out where the problem is and to make a timely decision by operators. There have been many studies on these problems but the results are not good enough for applying to real power system. Therefore power system operators always had to judge the exact state of power system and had to be preparative for the problems that can occur later. We developed new methods that can be applied to complex power system by dividing the system into small modules. By using 'module' we can combine small modules together to make complex power systems and the knowledge base that is applied to fault diagnosis system. As a result, compared to previously developed diagnosis products, operational time has shortened, and the knowledge base becomes simpler and clearer, which made online usage capable. This system can be used as a complementary measure that helps the operator from making any mistakes.

본 논문은 계통운영상황에 따른 대응책을 통하여 계통운영상태(state)를 구분하는 방법론을 제안한다. 일반적으로, 계통운영상태는 정상상태와 비상상태로 구분되지만, 본 연구에서는 이를 정상상태, 주의상태, 경보상태, 비상상태, 회복상태 등의 5가지로 구분하여 정의하고자 한다. 그리고 계통운영상태를 실정단계와 적용단계로 구분하여, 실정단계에서는 각 계통운영상태에 대한 대응책의 비용을 반영하여 계통운영상태를 설정하며 적용단계에서는 계통운영한계 및 각 대응책의 시행시간과 계통운영한계 초과시간 등을 고려하여 계통운영상태를 적용한다. 특히, 본 연구에서는 계통운영상태를 고려한 계통운영절차를 flowchart로 제시한다. 이러한 계통운영 상태는 계통운영자에게 계통운영에 대한 객관적 판단의 근거를 제시해 줄 것이다.

The cost losing synchronous through a transient instability is extremely high in modem power systems. This paper presents a power transfer capability calculation algorithm considering transient stability. The theoretical development is straightforward: dynamic equations are converted to numerically equivalent algebraic equation and then integrated into the standard formulation for power transfer capability calculation. The proposed method is applied to IEEE-24 Reliability Test System and the results shows the effectiveness of the method.

A improving method of the time efficiency to be necessary during the short-circuit tests that use high-priced equipment. Minimizing a human error through the database of relevant standards prospects a reliable tests. This paper describes the design concept and overall process of the development of the application that is developed in order to realize these functions.

본 논문에서는 향후 남한의 예비력 중대방안으로 동북아 지역 (러시아, 중국, 몽고, 북한, 한국, 일본)의 지역의 전력계통연계선로의 구성 및 동북아 지역의 계절별 패턴을 고려한 조류계산을 수행하여 전력수급의 분포도를 파악하고자 한다. 특히 한반도 전체의 전력수급을 고려하여 볼 때 남-북한의 수도권 및 영남 지역의 두 지역은 향후 계속적인 전력 수요의 증가로 인한 발전력의 부족상태가 계속되리라 여겨지며, 이러한 문제의 해결방안으로 북한의 신포지역에 2,000MW KEDO 경수로를 건설하여 공급하는 방안이 있겠으나 현재 여러 가지 정치적 상황으로는 건설을 중단하게 되었다. 이러한 정치적 상황의 변화로 다른 대안이 필요하게 되었다. 이들 중의 하나가 극동러시아나 시베리아 및 중국 그리고 일본과의 연계에 의한 예비력을 확보하는 방안이 될 것이다. 본 논문에서는 동북아 지역과 연계를 할 수 있는 가능한 지역을 고려하여 연계선로를 구성하고 계절별 효과를 고려한 조류계산을 실시하여 연계 시 융통전력의 분포도를 연구하고자 한다.

Recently over dropped frequencies of power system were recorded when power system was unbalanced between generation and demand. Therefore load following characteristic analysis of thermal and combined cycle power plant generators is necessary for low frequency condition analysis of power system. Frequency simulator supplies simulated frequency to the online generator for prescribed goal. This simulator needs to minimize effects to power system and requires stability first. This paper introduces design and manufacturing case of frequency simulator for load following characteristic analysis of generators.

This paper presents a method to improve reliability by dispersed generation (DG) installation considering load types and interruption cost. The objective functions such as power losses cost, operation cost of DGS, power buy cost and interruption cost are minimized for reliability improvement and efficient operation. The several indices for reliability evaluation are improved by dispersed generation system installation.

본 논문에서는 분산전원 계통을 모의하기 위한 시뮬레이터의 설계와 시험에 대한 내용을 제시하고자 한다. 제시하고자 하는 시뮬레이터는 RTDS(Real Time Digital Simulator)와 전력 증폭기(power amplifier)로 구성된다. RTDS 부분은 분산전원이 적용되는 계통의 모의와 분산전원의 전원부 모의를 위해 사용되며 전력 증폭기는 RTDS에 의해 모의된 전력 계통의 모선 전압 출력과 분산전원 전원부의 전압 출력을 증폭하기 위하여 사용된다. 시뮬레이터 구성을 위해 사용되는 RTDS의 구성과 제작된 전력 증폭기의 사양과 동작시험에 대한 결과를 제시하고자 한다. 개발된 시뮬레이터는 분산전원의 동적 및 정적 성능 평가를 위한 시험 시스템 개발에 적용될 수 있다.

본 논문에서는 IEEE123 모선 배전계통에 분산전원 투입이 가능하도록 GUI 조류계산프로그램 개발하였다. 첫째로 제안된 배전용 조류계산 프로그램은 기존의 배전용 조류계산의 한계를 벗어나 분산전원을 투입을 가능하게 하고 비주얼하게 온라인으로 배전계통의 구조를 컴퓨터 마우스 클릭으로 손쉽게 할 수 있도록 구성하였다. 둘째로 GUI부분에서 모선, 선로, 차단기의 정보를 표시할 수도 있고 사용자가 분산전원의 투입이나 차단 그리고 선로 및 부하의 투입 및 차단이 가능하도록 하였다. 개발된 프로그램은 데이터 변환기, 조류계산프로그램 및 GUI로 구성되어 있으며 이 3부분은 메시지 Queue 명령에 의하여 서로 메모리를 공유하도록 되어있다. 분산전원 투입 및 차단은 4군데로 지정하여 분산전원 투입량의 효과를 시각적으로 표시하는 데 편하도록 되어 있다. 조류계산의 결과는 GUI상에 유효전력, 무효전력, 모선전압, 역률을 각 모선의 근접 위치에 나타낸다.

Voltage control and stability problems are very important in the electric utility industry. But there is no voltage stability analysis program which has reliability as commercial program in domestic. We are developing a practical voltage stability analysis program. In this paper, we will study the existing commercial program and then discuss design of practical analysis tool.

This paper presents practical applications of reactive power and voltage planning to obtain voltage stability and operational voltage level for 2005 year summer peak Korea power system. It also describes the new electric facilities, operation criteria, voltage levels, MVAr flows, reactive power reserves in each control area. And reactive compensation devices are installed to maintain established voltage levels and stability margins. This simulation results show the improvement of voltage levels and the increase of reactive margins & interface flow margins. Finally, the paper reports the necessity of dynamic reactive reserves. It can be applied to analysis reactive compensation requirements and P-V & V-Q curves by PSS/E & VSAT.

현재 한전은 전력자동화시스템에 다양한 통신매체를 사용하지만 경제적, 기술적, 지역적, 운용 및 유지보수 측면에서 문제점을 내포하고 있어 다양한 통신망을 적용하여 자동화시스템을 사용 중에 있다. 산악지역이나 오지는 대부분이 유 무선통신 취약 지역이므로 이에 대한 감시 제어망 구축이 힘든 형편이다. 이러한 여건 속에 국내 위성사업의 기술력 확보, 이용료 하락 및 활성화로 위성통신이 경쟁력 있는 통신망으로 부상되고 있다. 하지만 현재의 위성통신서비스는 방송서비스 및 음성서비스가 대부분이며, 위성통신을 이용한 데이터서비스는 일부회사에 국한하여 사용 중에 있다. 또 전력산업구조개편에 따라 분사된 발전소 와 전국에 산재한 배전사업소의 광역 네트워킹에 대한 필요성도 증대되고 있는 시점이다. 본 연구에서는 산재되고 분산되어 있어 감시제어가 힘든 기기에 대한 통신망 해결책을 제시한다. 또한 전력서비스에 적용하기 위한 위성통신망을 구축하고 전력산업 관리의 효율성을 극대 화하기 위한 적용방안을 제시하고자 한다.

전력선 통신은 전기공급을 위해 기존에 설치되어 있는 전력선을 그대로 이용한 것으로 통신망을 새롭게 설치할 필요가 없다는 편의성 및 경제적 잇점을 가지고 있다. 최근 전력선 통신 기술은 홈오토메이션, 자동원격 검침, 원격모니터링에 적합한 기술로 주목받고 있다. 특히 전력선통신을 이용한 전력 감시시스템의 구축도 가능할 것으로 보여진다. 본 논문에서는 기존의 전력선 모뎀과 전력 측정 장비인 ACM meter를 이용하여 감시 시스템을 구성하였고, 전력선 모뎀과 ACM meter의 연계를 위하여 8051 kit를 자체 제작하여 ACM meter의 측정 데이터가 전력선 모뎀을 거쳐 컴퓨터에 모니터링 되도록 함으로써 차후 전력선 통신을 이용한 원격 감시시스템의 가능성을 연구하였다.

Available transfer capability(ATC) is an important indicator of the usable amount of transmission capacity accessible by several parties for commercial trading in power transaction activities. This paper deals with an application of optimization technique for available transfer capability(ATC) calculation and analyzes the results of ATC by considering several constraints. Sequential quadratic programming(SQP) is used to calculate the ATC problem with state-steady security constraints. The proposed method is applied to 10 machines 39 buses model systems to show its effectiveness.

This paper describes the consideration of relaying systems in case of applying superconducting devices to Korean power system. First of all, this paper investigates relaying systems in Korean power system and then do a basic study on relaying systems in the power system with superconducting devices. This paper is only provisional result of the study. For the more detailed result, the study using EMTDC relaying system modeling will be done from the viewpoint of superconducting devices application in the future.

HTS (High Temperature Superconducting) Transformer has the several useful characteristics in the viewpoints of technical and economical. Especially, an HTS transformer replaces the copper wire coils in a conventional transformer with lower loss HTS wire In addition, inexpensive, environmentally benign liquid nitrogen replaces the conventional oil as the electrical insulation (dielectric) and provides the necessary cooling for the HTS transformer Therefore, the Life-cycle cost of an HTS transformer is much more attractive than conventional because it is more energy efficient, lighter in weight, smaller in size, and environmentally compliant. HTS transformer can be the best way to replace with conventional transformer in the future. In this paper, we investigate the expected price of HTS transformer to have a merit in viewpoint of economic aspect. First, life-cycle cost of conventional transformer is calculated and based on this, the expected price of HTS transformer is evaluated, which HTS transformer is competitive against conventional transformer.

본 논문에서는 Lie Group theory에 기준한 $H_{\infty}$ 스위칭 제어기에 의한 비선형 전력계통안정화장치 (NPSS)를 설계하고 이를 1기 무한 모선에 적용하여 제안된 제어기의 제어효과 및 영향분석을 실시하였다. 이 분석에 사용된 기존의 PSS type은 Lead-lag 형태의 선형화 제어기이며, 제안된 제어기는 전력계통에 매우 강한 비선형을 반영하여 제어가 가능한 Lie Group theory에 기준한 비선형 제어기로 되어있다. 제안된 Lie Group theory에 기준한 비선형 전력계통안정화장치 (NPSS)의 효과분석은 MATLAB을 이용하여 1기 4차 비선형 전력계통의 모델에 적용하여 시뮬레이션하였다.

본 논문에서는 Lie Group 및 Lie Transformation의 수학적인 근원을 분석하고 이를 비선형 제어기에 제공하였다. 제어기의 구성형태는 Lead-Lag와 LQR 관측기를 결합한 혼합형 비선형 전력계통안정화장치(NPSS)이다. 이 분석에 사용된 제어기는 첫째로 기존의 PSS type인 Lead-Lag 형태의 선형화 제어기이다. 둘째로 제안된 제어기는 Lie group theory를 적용하여 이를 상태변수에 반영한 Lead-Lag와 LQR 관측기를 결합한 것이다. 제안된 혼합형 비선형 전력계통안정화장치(NPSS)의 효과분석은 MATLAB을 이용하였다. 분석모델은 1기 4차 비선형 전력계통의 모델에 적용하였다.

This paper investigates the effect of weather factors(such as winds, rain, snows, temperature, clouds and humidity) on transmission line outages. The result shows that weather variables have significant effects on the transmission line historical outages and the relationship between them is nonlinear. Multiple regression analysis using Logit model is proved to be appropriate in forecasting line failure rate in KEPCO systems. It could also provide system operators with useful informations about system operation and planing.

Optimal Power Flow (OPF) is becoming more and more important in the deregulation environment of power pool and there is an urgent need of faster solution technique for on-line application. So this paper presents parallel genetic algorithm-tap search for the solution of the OPF. The control variables modeled unit active power outputs, generator-bus voltage magnitudes and transformer-tap settings. A number of functional operating constraints, such as branch flow limits, load bus boltage magnitude limits and generator reactive capabilities are included as penalties in the fitness function. In parallel GA-TS, GA operators are executed for each process. If best fitness of the GA is not changed for several generations, TS operators are executed for the upper three populations to enhance the local searching capabilities. With migration operation, best string of each node is transferred to the neighboring node after predetermined iterations are executed. For parallel computing, we developed a PC-cluster system consisting of 8 PCs. Each PC employs the 2 GHz Pentium IV CPU and is connected with others through ethernet switch based fast ethernet. To show the usefulness of the proposed method, developed algorithm has been tested and compared on an IEEE 30-bus system in the reference paper. From the simulation results, we can find that the proposed algorithm is efficient for the OPF.

본 논문에서는 송전 계통사고 시 부하차단 이후 우리나라 2005년 계통에 대하여 전력계통안정화장치(Power System Stabilizer : PSS)의 영향 및 효과를 캐나다 Powertech Labs Inc.,의 TSAT(Transient Security Assesment Tool)을 이용하여 분석하였다. 모의를 위한 송전선로의 사고는 765kV 선로와 345kV 선로를 대상으로 하였으며, 8개의 모선에 대하여 상정 사고를 발생시켜 선로 차단 및 재투입을 고려하여 실시하였다. 본 연구에서 TSAT에 대한 기존의 전통적인 형태인 IEEEST type과 보다 정교한 이중구조를 가진 PSS2A type의 두 가지를 검토한 결과를 살펴보면 절반의 경우가 발전단 인근 지점의 사고시 발전기가 안정을 회복하지 못하고 탈조하는 것으로 나타났다. 그 외의 지역의 모선 단의 PSS투입효과는 비교적 댐핑 효과가 있는 것으로 나타났다.

The purpose of this paper is to explain improvement of voltage stability using STATCOM by active power margin and reactive power margin. STATCOM, the representative shunt compensator of the FACTS devices, is faster than machinery compensator in response speed and has the advantage of the small scale because it doesn't use reactor or large capacitor. In this paper, we investigated the compensatory effect of the STATCOM that applied to KEPCO system.

본 논문에서는 먼저 유효전력 시장과 무효전력 시장을 분리하여 운영한다는 가정하에서 발전기의 무효전력 생산을 위한 최적의 전압값을 산정하고자 한다. 유효전력 시장에서 경제 급전(Economic Dispatch)을 통해 발전기의 유효전력 생산 비용을 최소화시키는 최적의 유효전력량 결정원리를 응용하여, 무효전력 시장에서의 발전기의 무효전력 생산 비용을 최소화시키는 최적의 발전기 전압 profile을 결정하는 무효전력시장 구축 알고리즘을 제시한다. 이 알고리즘에는 기본적으로 주효전력-전압의 조류방정식과 목적함수로서 무효진력 비용의 최소화 문제, 그리고 부하측 전압과 관련된 부등식제약조건의 선형화 문제 등이 포함된다. 이렇게 산출된 발전전압에 의한 무효전력의 가격은 실제 전압제어에 의한 가격산정이라는 측면에서 그 의미를 찾아볼 수가 있다.

The paper proposes a simulation model of grid-connected photovoltaic generation system (PV system) using on PSCAD/EMTDC, a reliable power system and apparatus transient analysis program. A equivalent circuit model of a solar cell is used for modeling solar array. A series of parameters required for array modeling are deduced from general specification data of a solar module. A PWM voltage source inverter (VSI) model is presented and current control scheme is implemented for VSI control. A maximum power point tracking (MPPT) technique is applied for controlling the PV system. Simulation case study provides V-I and V-P characteristics of solar array and PV system control performance for irradiation changes.

기술의 비약적 발전에 따라 전기품질에 민감한 기기가 증가하고 있고, 비례하여 전기품질 저하에 따른 피해가 커지고 있다. 이러한 문제점을 해결하기 위해서는 공급자 뿐만 아니라 수요자 입장에서 문제점을 규명하고 해결책을 제시함으로서 각각의 이해관계에 따른 이러한 문제점을 해결할 수 있다. 본 논문에서는 전력품질 분석을 편리하게 수행하고 분석결과를 직관적으로 사용자에게 제공하기 위한 편리한 사용자 인터페이스 구성을 제공한다.

실시간 데이터를 대상으로 하는 전력 계통응용 프로그램을 개발하기 위해서는 SCADA 시스템이 다루는 Point Data를 Device Level의 속성으로 해석할 수 있어야 한다. 본 논문에서는 이러한 관계를 나타낼 수 있는 Mapping 기법을 제안하고 실제 응용 프로그램에 적용한 사례를 소개하고자 한다.

최근 들어 전력 공급의 신뢰성 강화를 위해 변전설비 고장을 미리 진단할 수 있는 예방진단기술이 절실히 요구되고 있으며, 한국전력공사 및 기타 수요자 층에서 예방진단기술 도입을 추진하고 있다. 또한 센서 기술과 디지털 기술, 통신 및 컴퓨터 기술의 발전과 더불어 실시 간으로 변전설비를 감시할 수 있는 온라인 예방진단이 가능하게 되었다. 이에 본 논문에서는 변전소용 온라인 예방진단 시스템을 현장에 적용한 사례를 소개 하고자 한다.

The second harmonic component could be decreased by magnetizing inrush when there have been changes to the material of the iron core or its design methodology. The higher the capacitance of the high voltage status and underground distribution, the more the differential current includes the second harmonic during the occurrence of an internal fault. Therefore, the conventional second harmonic-restrained RDR needs modification. This paper describes an advanced numerical algorithm that utilizes terminal voltage, differential current harmonics, harmonic ratio, and flux-differential current slope. Based on the results of testing with WatATP99 simulation data, the proposed algorithm was proven to be faster and more reliable.

In the paper architecture of load flow under graphic interface we mentioned that the define of graphic interface and the way of system modeling. In the view point of engineering, domain define is the step of process which is seek out the general solution. This is a base of program's structure. When making a relationship inner component, relevance and restriction are affected by data type and etc. In this process logical data is realized as a symbol. And system configuration decide that main function and extension by the analysis user's demand and requirements. Specially engineering analysis software has accuracy also through the numerical method. To represent this wee need more powerful graphical component. This helps user's accessibility. We can combine 10, numerical library and graphical component as a system element by domain definition. In this paper we will materialize as a step of implementation and decide a direction of programming. In conclusion we will see the analysis software's necessary function to make a better.

This paper describers the power demand and the voltage stability in power system. Especially the power demand on summer is more and more increase in korea. According to load quantity is increasing voltage is getting down. And power system becomes unstable. So this paper is prevent voltage down using to ULTC modeling which is a part in a transformer. Therefore our purpose is power system stability increasing as variable state like a load increasing or a fault. Then this paper is using IPLAN and PSS/E as analysis tool. PSS/E is very powerful engine on load flow analysis. And IPLAN is capable of using on variable program compiling with user.

In a new competitive market environment, it is very important to determines how much power can be transferred through the network. It's known as Available Transfer Capability(ATC). This paper presents a technique to evaluate Reliability Assesment and the Available Transfer Capability of Haenam-Cheju HVDC transmission system using Well-being Method which is based on the probabilistic method. The system Well-being is categorized in terms of the system Healthy and Marginal in addition to the conventional Risk index. Haenam-Cheju HVDC system has been studied for the optimal ATC based in well-being categories.

This paper is proposed that The voltage-dependant power factor model is established as 5th polynomials with convenience data type. This modeling includes the harmonic components by static experiments of individual and composite load. This paper suggested methodology for modeling bus and regional power factor with consideration of harmonics effect by load composition rates and individual load power factor models.

매년 에너지 사용이 급증하고 있는 우리나라 현실을 고려하여 본다면 에너지 비용 상승에 대한 수용가의 능동적 대책이 절실히 요구된다. 단순한 에너지 감시 차원을 넘어서 수용가의 에너지 사용 계획 수립에 도움이 될 수 있는 전력 에너지 분석 정보가 요구된다고 할 수 있다. 본 논문에서는 당사에서 개발 중인 전력 에너지 사용량 분석 프로그램의 주요기능과 시스템 구성에 대하여 소개하고자 한다.

이 논문에서는 Nonlinear Observer Backstepping 출력 궤환 제어에 의한 비선형 전력계통안정화장치(NPSS)를 개발하였다. 이 기법은 출력단자의 측정만으로 매우 강한 전력계통의 고유한 특징인 강한 비선형을 처리할 수 있는 바람직한 제어기를 구성할 수가 있다. 첫 번째로 비선형 관측기를 통하여 측정할 수 없는 부분의 상태들을 대신할 수 있는 출력 궤환 관측기를 구성하는 것이다. 두 번째로 이렇게 구성된 관측기에 매번 상태를 반영할 수 있는 backstepping 제어기를 적응하는 것이다. 시뮬레이션을 통한 제안된 제어기의 효과는 비 제어시, 기존의 Lead-Lag PSS, 그리고 제안된 Nonlinear Observer backstepping 출력 궤환 제어에 기준한 비선형 PSS를 비교 검토하였다.

Maximum short circuit current of modern power system is becoming so large that the current should transmission capability. Although there are various kinds of method to solve this, approached from super conductivity Fault Current Limiter application viewpoint among them. High Temperature Superconductor-Fault Current Limiter (HTS-FCL) development is progressing according to HTS technology development, and system application is tried. For actual system application of such super conductivity FCL, an more efficient method was developed to find suitable FCL application locations using sensitivity factor comparing previous paper.

This paper proposes the discrimination method for the fault location, whether it is within the line where the distributed generation(DG) is integrated or out of the line (but sharing the same bus of the substation). In general, DG has to be disconnected from the grid when the fault occurs on the interconnected distribution feeder as soon as possible. However, the faults occured on the neighboring feeder would mistakenly cause the disconnection of the DG. For reliable operation of DG, DG should be sustained at the fault occurred on neighboring distribution feeders. The proposed identification method utilizes the impedance monitored from the DG and examines the coordination of overcurrent relay of the distribution system. This paper describes how the proposed method to identify the faulted feeder and how the method can be utilized.

The lower voltage distribution box of service wire has been usually employed to supply an electric power to the consumers through low voltage overhead line. Now-a-days, electric shock accident at the distribution box of service wire installed in the seashore areas has been often occurred. The reason is mainly due to the electric leakage in the distribution box of service wire. This paper described insulation breakdown mechanism of distribution box of service wire, analysis of electric shock path and safety countermeasure of distribution box of service wire.

Harmonic resonant overvoltage during restoration of primary restorative transmission system originates in switching operations and nonlinear characteristics of equipments. Actually it is difficult to predict the occurrence of harmonic overvoltage, since they result from nonlinear characteristics of transformers and other equipments. This paper describes the analysis of domestic primary restorative transmission system using PSCAD/EMTDC. The harmonic resonance is verified and showed the relation with equipments which have nonlinear characteristics such as generator and transformer in this paper. And the solution to prevent harmonic resonance is proposed too. As a result, the PSCAD/EMTDC simulation showed slightly conflictive results that had been presented by IEEE Power System Restoration Working Group report.

This paper studies power quality problem of utility interconnected distributed generation. Recently, electronic devices that are sensitive to power quality have been increasing. Both utility and customer are interested in power quality problem. Therefore, we studied an effect of utility power quality caused by distributed generation. We detect and analysis voltage sag which is one of power quality indicator. Also, we used Matlab to simulate power quality problem.

In a competitive environment of electric power industry, the level of uncertainly increase due to generation investment decisions creating new challenge to transmission system planner. The use of a locational signal and the provision of a indicative plan to control the transmission investment reasonably is very important in the viewpoint of a regulator. The main target of this study is to emphasize on the necessity for considering simultaneously both transmission expansion plan and congestion cost. This paper demonstrate the many case studies to make certain of the necessity for transmission planning with congestion cost.

This paper analyse a operating characteristics when the Community Energy System (CES) is operated islanding mode. In the near future, CES might be one of major energy supply structures. The basic concept of CES is that it supplies electrical and thermal energy to the local customer loads through the islanded power network separated from the grid. The CES must be supplying local load with stable energy on the islanding mode, analysing necessary to thoroughly the operation feature. In order to show them, in this paper, we model the CES with 2.34 MVA DG and simulate the operating feature on the islanding mode of CES. The simulation results show that, in order to stability operate, the CES need the efficient load management and generation control schemes during the transition periods.

This paper proposes a fuzzy dual method for analyzing long-term transmission system expansion planning problem considering ambiguities of the power system using fuzzy lineal programming. Transmission expansion planning problem can be formulated integer programming or linear programming with minimization total cost subject to reliability (load balance). A long-term expansion planning problem of a grid is very complex, which have uncertainties fur budget, reliability criteria and construction time. Too much computation time is asked for actual system. Fuzzy set theory can be used efficiently in order to consider ambiguity of the investment budget (economics) for constructing the new transmission lines and the delivery marginal rate (reliability criteria) of the system in this paper. This paper presents formulation of fuzzy dual method as first step for developing a fuzzy Ford-Fulkerson algorithm in future and demonstrates sample study. In application study, firstly, a case study using fuzzy integer programming with branch and bound method is presented for practical system. Secondly, the other case study with crisp Ford Fulkerson is presented.

This paper presents the greenhouse gas emission trading scheme which is under progress as a pilot project at the power sector in preparation for UNFCCC. By referring UK's, Emission Trading is introduced incentive auction to maximize the reduction of greenhouse gas emission. At the 1st step, from year 2006 to 2008, only CO2 is regarded as an objective target to decrease but emission credit is excluded with an assumption and only 5 Generation company take part in as participants. The market operating procedure is composed of participants' registration, baseline verification, incentive auction, the registration of initial and yearly allocation, emission trading, yearly emission verification & approval, yearly obligation conformity, carry forward & incentive grant. It can be serve a guideline the whole aspects of emission trading which will start in 2006 including operation, verification and profit sharing.

전력산업 구조의 변화와 전력수급의 안정성 확보를 위해, 다양한 전원개발에 대한 연구가 시도되고 있다. 본 연구에서는 현재 미국에서 시행하고 있는 수요응답자원(Demand Response Resource)에 대한 수요응답 프로그램(Demand Response Program)의 성과를 조사하고 이를 분석하였다. 미 연방에너지 규제위원회(FERC)의 시장표준안과 각 주의 공익규제위원회(PUC)에 규제에 의해 대부분의 미 전력시장에서는 이러한 수요응답 프로그램을 시행하고 있다. 본 논문에서는 미국 전력시장을 대표하는 New England ISO, PJM, 그리고 NYISO 세 곳의 수요응답 프로그램 효과를 조사하였다. 본 논문에서는 수요응답 프로그램의 참여자 수와 수용응답 이벤트 발생 건 수, 총 차단부하량, 평균 차단부하량, 그리고 지급액의 관점에서 수요웅담 프로그램의 효과를 조사하였다.

양방향입찰시장(TWBP)의 도입을 위해서는 이를 위한 시장설계 및 효율적인 시장운영을 위한 다양한 분석 작업들이 요구되고 있다. 특히 시장설계의 경우, 해외 자문회사와의 협력을 통해 경쟁적 전력시장을 이미 도입하여 운영하고 있는 해외 국가들의 사례들을 포함한 많은 시장운영 기법들이 검토되고 있으며 향후 도입될 TWBP 전력시장에 적합한 방안들을 준비하고 있다. 전력을 전력시장운영규칙이 정하는 바에 따라 전력시장을 통해서만 거래하도록 규정하고 있는 우리나라의 경우, 전력시장운영규칙은 전력시장과 전력계통의 운영에 대한 모든 것을 다루게 되는 만큼 이에 대한 합리적인 설계와 적용은 효율적인 TWBP 전력시장의 기본 틀이라고 할 수 있다. 양방향입찰시장에서의 가격결정은 전력수급과 시장가격 안정화를 위해 매우 중요한 사안이다. 또한 현재 CBP시장과 다른 용량요금(CP)제도의 폐지와 기타 공급예비력확보 제도 등 도매시장설계에 있어 중요한 자료를 제공한다. 양방향입찰시장하에서 가격수준 분석을 통해 시장개설 이전에 문제점을 사전에 검토하여 문제점을 개선하고 시장규칙에 반영하여야 한다. 또한 용량요금 폐지에 따른 보완대책을 수립하여 수급불안정을 방지하고 전력시장 안정화와 성공적인 도매경쟁시장 개설을 위해 필수적이라 할 수 있다. 본 논문에서는 CBP 시장과 TWBP 시장에서의 기본적 가격예측을 위한 구조적 모델링과 일부 시나리오에 대한 결과를 소개하고자 한다.

Although Jeju island Is connected with main network system by HVDC cable line, it's network assumes the form of independent system in an operating point of view. Therefore Jeju needs it's own independent capacity expansion planning. Continuos growth of demand and increase of antiquated plants in Jeju requires additional generating capacity. This paper analyzes characteristics of two alternatives which include it's own expansion of facilities and capacity expansion of network system for Jeju island. Furthermore this paper evaluates economic efficiency of those alternatives and analyzes long-term program of demand-supply of electricity.

This paper analyzes the customer behavior on the high-efficiency lighting program from three angles, that is, rebates, electricity rates and the cost of measures. After deregulation, the importance of high efficiency DSM programs has been more and more increased. Especially, the new high-efficiency lighting apparatus has been developed and adopted as DSM program, so it is needed the policy to promote the lighting program diffusion.

All over the world, including England & Wales, USA(PJM, California, New York etc.), Australia, New Zealand, Canada and Korea, experience deregulation in the electric power sector. Inevitably, new terminologies associated with this field are generated more and more. Therefore, this paper proposes explanation principles of new terminologies in electric power deregulation.

When Power market is restructured, we have an argument with selecting Transmission loss factors. First, we determine the method of calculating Transmission loss factor using OPF (Optimal Power Flow) or PF (Power Flow Equation). Then, we decide that we applicate the factor which are identical value all the year or which are floating Transmission loss factor every each hour. In this study, we accomplish the method of computing Transmission cost in competitive market.

Korea adopted feed-in-tariff system for diffusing the generation using renewable energies in 2002. But, there are many debatable issues about Korea's feed-in-tariff system, such as application duration and tariff level by the renewable energies. This paper surveys problems and issues which has been discussed for two years.

Generally, there are two types of regulation strategies for encouraging renewable energies ; regulation by quantity and price. With examples of quantity regulation, there RPS (Renewable portfolio standard) system in United States America, Renewable obligation in England, and MRET system in Australia. Countries that chose the price regulation are Germany, Spain, France, Portugal. This Paper overviews the current trends of regulation system on policies for renewable energies in foreign countries on these days.

This paper proposes a new protective relaying algorithm using ACI(Advanced Computational Intelligence) and wavelet transform. To organize the advanced neuro-fuzzy algorithm, it is important to select target data reflecting various transformer transient states. These data are made of changing-rates of D1 coefficient and RSM value within half cycle after fault occurrence. Subsequently, the advanced neuro-fuzzy algorithm is obtained by converging the target data. As a result of applying the advanced neuro-fuzzy algorithm, discrimination between internal fault and inrush is correctly distinguished within half cycle after fault occurrence. Accordingly, it is evaluated that the proposed algorithm can effectively protect a transformer by correcting discrimination between winding fault and inrushing state.

This paper proposes a method for choosing the best composite power system expansion plan considering probabilistic reliability criterion. The proposed method was modeled as the minimization of the investment budget (economics) for constructing new transmission lines subject to not only deterministic(demand constraint) but also probabilistic reliability criterion(LOLE) with considering the uncertainties of the system elements. This is achieved by modeling the power system expansion problem as an integer programming one. The method solves for the optimal strategy using a probabilistic theory based branch and bound method that utilizes a network flow approach and the maximum flow-minimum cut set theorem. Although the proposed method is applied to a simple sample study, the test results demonstrate a fact that the proposed method is suitable for solving the power system expansion planning problem subject to practical uncertainties for future.

본 논문에서는 급전지역분소 전력감시 시스템 운영자를 대상으로 하는 훈련시스템을 제안하였다. PC Platform에서 개발하여 운영자가 용이하게 설치, 관리가 가능하도록 하였으며 현재 설치되어 있는 SCADA 시스템의 MMI와 유사하게 구성하여 SCADA 조작 훈련에 대한 효과를 극대화 하였고 SCADA 데이터 베이스와 동일하게 데이터베이스를 구현함으로서 데이터 베이스 조작훈련이 가능하고 차단기 제어시 COS처리, 이벤트 발생에 대한 시각화를 용이하게 하여 운영자로 하여금 SCADA 시스템의 동작에 대한 이해를 도울 수 있도록 처리하였다. 또한, 모의사고 발생기능을 지원하여 사고 발생시 차단기의 동작 및 이에 따른 전력계통의 변화를 훈련자가 인식할 수 있게 하였다. 제안한 시스템으로 인하여 SCC SCADA 운영자에 대한 용이한 훈련이 가능함으로서 실제 SCADA 조작시 오조작을 방지할 수 있으며 사고발생시 신속한 복구작업을 가능하게 함으로서 전력계통 운전의 효율성을 향상할 수 있는 효과를 가져올 수 있다.