In this study. the microwave dielectric properties, such at dielectric constant(${\varepsilon}_{\gamma}$), unloaded quality factor multiplied with resonant frequency($Q_{u}$.f), and temperature coefficient of resonant frequency(${\tau}_{f}$), were investigated for the low-temperature sintered (Pb, Ca)$ZrO_3$ with $V_2O_{5}$ additives as well as structural properties. As a result, (Pb,Ca)ZrO$_3$ with 0.2 wt% $V_2O_{5}$ additive, sintered at $1200^{\circ}C$, showed good properties like ${\varepsilon}_{\gamma}$ 109, $Q_{u}$.f 2736 GHz, and ${\tau}_{f}$ -2.94 ppm/$^{\circ}C$. Especially ${\tau}_{f}$ was much better than ($Pb_{0.63}Ca_{0.37}$)$ZrO_3$ of which ${\tau}_{f}$ was known to be + 13.4 ppm/$^{\circ}C$, so it seems to be applicated in micorowave device components.

In this paper, Dielectric and strain properties of (1-x-y)PMN-yPT-xST Ceramics hale been investigated as a function of the amount of SrTiO$_3$(ST). The SrTiO$_3$ content is ranged from 0.01-0.05(wt%). As the amount of ST is increased, dielectric constant has a maximun value at 0.05 mol% composition. The Curie temperature is decreased linearly with increasing ST composition and Polarization properties have been investigated. Coercive field and remnant polarization has a maximum value at 0.01mo1% composiion.

Epoxy-Ceramic Composite have good insulating, therma1 and mechanical properties, so it is studied actively on this material. In this thesis, we made a composite material b)\ulcorner filling Epoxy Resin with ceramics treated with Sillane Coupling Agent and studied dielectric and insulating characteristics according to treatment density of Sillane Coupling Agent and weight percent of filler. As a result, loss tangent increase and electrical breakdown voltage decrease according to increasing treatment density of sillane coupling agent because Interface matching between matrix and filler is not good. The best treatment density of sillane coupling agent is 0.5% water solution, in this density the best interface matching is achieved so good dielectric and insulation characteristics are shown. Dielectric and insulation characteristics according to weight percent of filler are best at 25wt.

The porous PZT was prepared from a mixture of PZT and polyvinylalcohol (PVA ) powders by BURPS( Burnedout Plastic Sphere) technique. The dielectric and piezoelectric properties of piezoceramic/polymer composites dependent on the PVA wt. % were evaluated. The density of PZT/polymer 3-3 composites were decreased almost linearly with increasing the PVA wt. %.

PTCRl(positive temperature coefficient of resistivity) thermistors in the thin file BaTiO$_3$ system were deposited by radio frequency (13.56 MHz) and dc radio frequency (13.56MHz) and dc magnerton sputter equipment. R-T(resistivity -temperature) properties was investigated as a function of substrate and the temperature variation. The specimens make a comperison between the thin films and the bulk in the resistivity variation. Substrate temperature. deposition time. and forward power are deposited at the 400$^{\circ}C$, 10 hours, and 210 watt. respectively. The aim of this work is to obtain lower than bulk specimen resistivity in thin films BaTiO$_3$ system thermistor by RF/DC magnetron sputter equipment.

A piezoelectric actuator. which is composed of a piezoelectrically driven stator and a rotor, Is made and the characteristics are investigated experimentally is a new ultrasonic actuator which transforms rotary motion to linear one is proposed and proved to work successfully. If an ultrasonic wave is excited to propagate in the stator, particles on the internal surface move elliptically. Since the internal surface is machined as an internal thread and an external thread(rotor) is put into the stator. the external thread is rotated through the friction force and moved in the axial direction. The traveling wave is excited by a piezoelectric element bonded to the stator. This idea is firstly proposed by S. Ueha, et al. in 1987. However, efficiency of their actuator is less than 3%. In this study, in order to improve characteristics of this type actuator, we used various pitches and number of the screw thread, and materials of rotor, and we obtained good charcteristics.

Temperature dependences of the remanent polarization $P_{\gamma}$/(T), effective birefringence ㅿｎ(T). dielectric constant K(T) and quadratic electro-optic coefficient R(T) of the two-stage sintered xBa(La$_{1/2}$Nb$_{1/2}$)O$_3$Pb$(Zr_{y}Ti_{1-y})O-{3}$(x=0.085, 0.09, 0.40$\leq$y$\leq$0.70)ceramics were investigated. Increasing the PbZrO$_3$ contents, the crystal structure of a specimen was varied from tetragonal and rhombohedral to cubic, and the phase transition was showed a diffuse phase transition(DPT) characteristics. Especially. in the compositions which located on the PE-FE phase boundary were showed a discrepancy between curie temperature and temperature range which a macroscopic polarization and a effective birefringence were disappeared.

This paper studies on the effect of DSC(Differential Scanning Calorimeter) analysis condition on the glass transition temperature of silica filled epoxy network polymer used for ultra-high voltage apparatus. The effects of temperature scanning rate specimen size and gas flow rate on measured glass transition temperature have been studied in order to select optimum thermal analysis condition.

.In this study, we measured Ic depending on a curvature radios of High Tc superconducting tapes which were made of a single wire, two and three WIT(wire in tube). Wires are manufactured by the process of press ins and sintering (150h, at 845$^{\circ}C$ ) for the growth of 2223 high Tc Bi superconducting phase. We know that Ic of a single wire decrease with reduction of a curvature radius. The maximum Ic of 2 WIT wire is 2.54 (A) and have a better characteristic than a single wire (0.89 A) at a curvature radius 75mm.

The method of passivation for protecting the $Hg_{1-x}Cd_{x}$Te surface is important device fabrication process. Because the surface components are highly reactive leading to its chemical and electrical instability. Especially. the material of detecting for infrared radiation, of which composition is x=0.2 or 0.3, is narrow bandgap semi- conductor. The narrow bandgap semi conductors are largely governed by the properties of the semiconductor surface. The narrow bandgap semi-conductors are largely governed by the properties of the semiconductor surface. The electro-chemical processing of $Hg_{1-x}Cd_{x}$Te allows rigorous control of the surface chemistry and provides an in-suit monitor of surface reaction. So electro-chemical reduction at specific potential can be selectively eliminated the undesirable species on the surface and mainpulated to reproducibly attain the desired stoichiometry. This method shows to assess the quality of chemically treated good $Hg_{1-x}Cd_{x}$Te surface.

In this paper, we will report on the effect of the pointed end shape of an electrode, discharge energy, pulse width and discharge current on machining characteristics. The results obtained are as tollows: 1)As the discharge Energy increases, the diameter and the depth of the discharged crater becomes larger and deeper. 2) The discharge energy is not constant during discharge but varies depending on the pointed end shape of th8 electrode. 3) The shape of crater depends on the pulse width and discharge current.

In order to investigate possibility of CV cable diagnosis technique, residual insulation characteristics of .long - term serviced 0.6 kV CV Cable are examined by DC leakage current residual voltage tensile strength, cross1inking density and AC & impulse breakdown. Also effect of cable structure and water tree are reported

Partial discharge on organic insulation surfaces are an important sauce of aging. Furthermore the modern PD measurement technigues are rapid developed as quality control and diagnostic tests to determine the fitness for use of HV equipment employing sol id electrical insulation. This paper deals with theory of conventional PD measurement and new tendency of technical development on PD measurements und evaluations. Finally the Measuring system used for diagnosing the surface aging on the organic insulation at High Voltage Laboratory of Technical University of Darmstadt in Germany is presented.

Tact Electrical conductivity. optical absorption spectra of poly(p-phenylene vinylene) and their dependence on stretching are discussed in detail. The conductivity in the parallel direction to the stretching is higher over one order in magnitude than that in the perpendicular direction to the stretching is higher over one order in magnitude than that in the perpendicular direction to the stretching. The photocurrent spectrum for the ligh polarized parallel to the chain direction is much enhanced in lower photon energy compared with that for the light polarized perpendicular to that direction. The result may be originated in the difference of energies which is needed to photogenerate carriers wi th the light polarized parallel and perpendicular to the chain stretched direction.

This paper describes the developed sensor for measuring the time-varying magnetic fields and presents the characteristics of the magnetic fields and presents the characteristics of the magnetic field generated by lighting a fluorescent lamp. The frequency bandwidth of magnetic field measurement system is kknown as 40 Hz∼100 kHz by means of calibration experiment. The magnetic field waveform which originates from the various lighting systems was measured and the frequency components were analyzed by fast Fourier transformation technique. The magnetic field generated during the operation of the fluorescent lamp mainly includes the odd harmonics, and in the case\ulcorner of push button switch and high frequency starter types the fast transient component is occurred in an instant of lighting.

On this study, we fabricated humudity sensor with polyimide thin film from the nonaqueous emulsion by the electrophoretic deposition as a function of film thickness. then evaluated performance of the sensor with increasing relative humidity if constant temperature constant humidity chamber, which is electronically controlled. we designed upper electrode of the sensor to brush type to make moisture particles permeate into the polymer bulk. sensing properties of the sensor on % RH shows proportion on the low %RH. Fer the 30V-30S- 200$^{\circ}C$ sample, percentage changing of capacitance on from 30 %RH to 90 %RH is 45.8 %, and increasing rate per 1 % RH of capacitance is 11.25 pF

In this paper we have investigated discharge conditions(parameters of this experiment) in facing targets sputtering system and fabricated $Al_{N}$ thin films. The parameters of this study are diameter of wing(d) and distance(L) between two facing targets. Varing discharge conditions, the discharge characteristics are wide different. The optimal conditions in this experiments are d = 6.5 [cm], L = 6.5[cm]

Organic ultra thin films about 500${\AA}$ in thickness are fabricated by LB(Langmuir-Blodgett) technique and their gas detect properties are investigated. The LB films deposited are made of the specimen named as N-docosyl pyridinium(TCNQ) and the deposition is verified by capacitance conductivity measurement. From the study of gas detect properties with I-V characteristics and UV spectrum we have found that their conductivities were increased about 3 times of magnitude and peaks of UV spectrum were decreased.

We have manufacture Copper-tetra-tert-butylphalocyanine (CuTBP)Langmuir-Blodgett(LB) films, which is known be sensitive to NO$_2$ gab. A response of these films to the NO$_2$ gab was studied. A surface pleasure of 25mN/m was obtained as a proper one for a film deposition. A deposited film status was identified with Uv/visible absorption spectra, ellipsometry measurements, and current-voltage(I-Y) characteristics. The NO$_2$ gas response experiments under 200ppm conducentration show that there are increment of electrical conductivity by 12 times, 5 seconds of response time, and 5 seconds of response time, and 90 seconds of recovery time.

On this paper, the structural changes of molecules on the water surface were monitored by the measuring system of displacement currents. The measuring system was constructed at home-made Kuhn type LB(Langmuir -Blodgett) deposition apparatus. Solutions of 4-octyl -4\\`- (5-car boxy$.$ -pentamethyleneoxy) azobenzene molecules (8A5H) and stearic acid(C$\_$18/) were spreaded at the air-water interface respectively, and the currents inducted by the dynamic behavior of molecules were measured when the molecules were the molecules were pressed by barrier. From C$\_$18/ mo1ecules two distinct peaks of displacement currents were obtained, which show that the orientations of mo1ecules were charged largely at these Points. The reversibility of displacement currents by compression and expansion was obtained from 8A5H molecules, which shows the compressed molecules which shows the compressed molecules have a tendency to disperse after the compression. But it was not obtained from C$\_$18/ molecules which means that this molecules disperse not easily by decreasing the pressure of the barrier.

The effects of low molecular weight components of LDPE and sample molding condition were investigated to find the orgins for heterocharge in LDPE without any addtives. Low molecular weight chains of LDPE encourages the formation of heterocharge by being charged and migrating the counter electrode. The formation of heteroohage in LDPE was also effected by sample preparation process and the kind of a moling film. When PET film is used as a molding layer, the carbonyl, which may lead to increase the heterocharge, formed at surface of LDPE.

A surface acoustic wave(SAW) sensor for the detection of odorants has been constructed by depositing various phospholipids and fatty acids onto the surface of the SAW device. Applying the Langmuir-Blodgett technique. it was possible to deposit the optimal number of layer which was found to be between 10 and 20. The characteristics of a SAW device operating at 310 MHz deposited with phosphatidyl choline were analysed. Menthone, amylacetate, acetion, and other organic gases sho7\\\\`ed different affinities to the coated lipids. An explanation is given for differant odorant affinities based on the monolayer properties of phospholipids. The identification of odorants depending on the type of lipid used for coating is discussed in terms of a comparison of their normalized resonant frequency chi It pat terns. Using a number of different lipid-coated SAW devices. odorants can be identified by a computerized pattern recognition algorithm.

In this study, the thermally stimulated current(TSC) of corona charged PTFE film was studied and the simulation of corona charging process was also calculated by finite element method. The electrets which were formed by appling high voltages(DC-5∼-8[kV]) to PTFE film were experimented to measure TSC in the temperature range of -100∼+200 [$^{\circ}C$] and then the finite element method was accomplished to examine corona charging process using a obtained physical constants. It is confirmed that the charging negative corona is profitable as the applications are manufactured because the time constant of negative corona is much larger than it of positive corona. And it is attempted to estimate the corona charging process in space using simulation.

The use of preformed polymers and their cross-linking have been a attempted in order to improve the intrinsic fraqility of monolayers and Langmuir-Blodgett (LB)films and to make their technological applications possible. It has shown that an imidization followed a polyion-complexation can stabilize the LB films against heat and solvents. And when the polymer structure was properly designed concurrent removal of the alkyl tails together with imide formation could be accomplished. In this paper we present a characteristic monolayer behavior of polymer with pendent polythers and carboxyls it’s polyion-complexed LB film with subphase polymer PAA and a possible skeletonization of the LB film by thermal imidization. Also deposition status of LB films are evaluated by using QCM

An experimental study was carried out to investigate the fabrication process and electrical breakdown of electrodeposted polyimide film from nonaqueous emulsion onto metal electrode surface. The thickness of imide film control led by the deposition voltage and time are proportional to the voltage or time. From the results, yeilds is proportional to the total elctrical charge flow through the electrode. When electrophoretic deposition voltage is 30 [V] deposition time is 30 sec, 40 sec, 50 sec, then the thickness of the films are 2.13 $\mu\textrm{m}$, 2.69 $\mu\textrm{m}$, 3.16 $\mu\textrm{m}$, 3.94 $\mu\textrm{m}$, respectively Electrical breakdown voltage of polyimide thin film shows very high. As film thicknes increase, the breakdown voltage are increased, but are net directly proprotional to thickness of the film.

Decomposition products by crosslinking reaction of PE using Dicumylperoxide(DCP) should influence on the electrical properties in XLPE. This paper studies on Behaviors of Decomposition products and Electrical Treeing ding to Drying condition. We used the Gas Chromatography for Decomposition Gases analysis FT-IR for investigating the behaviors of Decomposition products remained in XLPE Break Down Voltage Tester for Electrical Treeing measurement.

We considered the ion and photo-induced properties as a function of wavelength by exposing the light over the band gap of a-Ag/a-$Se_{75}$$Ge_{25}$ and the low-energy defocused $Ga^{+}$ ion beam on Ag/a-$Se_{75}$$Ge_{25}$ thin film. This film acts as a negative resist for photo or ion beam lithography. We observed that the absorbance coefficient decreased with increasing the photo-exposing time and exposing the ion beam. The bandgap shifts toward longer wavelength called a "darkening effect" are observed in the films exposed to both photons and ions. We suggest that a primary step in the Ag layer and a secondary step is in a-$Se_{75}$$Ge_{25}$ film layer.

The characteristics of the Si-SiO$_2$ interface and the degradation in the short channel(L${\times}$W=1.7$\mu\textrm{m}$${\times}$15$\mu\textrm{m}$) SONOSFET nonvolatile memory devices, fabricated on the basis of the existing n-well CMOS processing technology for 1 Mbit DRAM with the 1.2$\mu\textrm{m}$ m design rule, were investigated using the charge pumping method. The SONOSFET memories have the tripple insulated-gate consisting of 30${\AA}$ tunneling oxide 205${\AA}$ nitride and 65${\AA}$ blocking oxide, The acceleration method which square voltage pulses of t$\_$p/=10msec, Vw=+19V and V$\_$E/=-22V continue to be alternatly applied to gale, was used to investigate the degradation of SONOSFET memories with the write/erase cycle. The degradation characteristics were ascertained by observing the change in the energy and spatial distributions of the interface trap density.

We examined the magnetic properties as a function of annealing temperature of the as-quenched $Fe_{87}Zr_{7}B_{5}Ag_{1}$ amorphous alloy. The values of $H_{c}$=30m0e, $B_{a}$=0.44T and ${\mu}$i=146000 at $300^{\circ}C$ annealing treatment are obtained. The excel lent soft magnetic properties seem to result from the annihilation of quenching-Induced internal stress by the heat treatment and the change of microstructure due to the different relaxation behavior owing to adding insoluble element such as Ag. Therefore, the $Fe_{87}Zr_{7}B_{5}Ag_{1}$ amorphous alloy is quite promising for practical use as a core material in various transformers of high transformers of high frequency.

We discussed the thermal analysis for recording media with the variation of the laser pulse duration and the power and the temperature distribution for the optimized Te-based antireflection structure by using the computer calculations. If the radial diffusion of heat is negligible, we can calculate the maximum temperature at the spot center in recording layer by Simple Method, and the temperature profile considering the specific heat and the latent heat by Numerical Method. As a result, the effect of the heat sinking which acted as a loss for the hole formation can be minimized by introducing the pulse of the hole formation duration( $\tau$ ) shorter than the thermal time constant( $\tau$$\sub$D/) of dielectric layer. This requirments can be satisfied as using the dielectric thickness of the 7nd ART condition or the dielectric materials with low thermal diffusivity.

For scale-down EEPROM, MONOS structures with the different thicknesses of gate insulators, are fabricated and the memory characteristics, such as swtching and retention characteristics are investigated. As a results, the devices with the top oxide of 20A thick were deteriorated in retentivity. However, 11V-programmable voltage for ΔV$\sub$FB/=4V and 10-year data retention were achieved in MONOS structure with the t7p oxide of 50 ${\AA}$ thick and nitride 45${\AA}$thick.

We fabricated Ag ion exchange glass waveguide. Generally, ion-exchange glass waveguide. are suitable for passive integrated optical components such as directional and star couplers. Its advantages include low loss, ease of fabrication, and low material cost. So, we faricated Ag ion-exchange glass waveguides in AgNO$_3$ melt solution from 2 mole %. And we used Sodalime glass as a substrate in the fabrication process. As the results, we observed multivalent ion-exchange in a typical sodalime glass. Diffusion coefficient and depth are predicted by actual experimental data of Stewart. The exchange rate in silver-ion-exchanged waveguides are compared to the exchange time of waveguide fabrication.

Infrared radiator of Cordierite system were manufactured using Cordierite(2Mgo$.$2Al$_2$O$_3$$.$5SiO$_2$) and Clay 30wt% as main materials and addition of MnO$_2$ from 0. 1 to 2 5wt% of Dry pressing and slip casting The effects of MnO$_2$ additives on the thermal properties of infrared radiator of Cordierite system. The more the thermal expansion could be lowered the more the amount (wt%) of additives MnO$_2$is increased in the below 4.5$\mu\textrm{m}$. The high efficiency Infrared radiator of Cordierite system using dry pressing method when the amount of additives MnO$_2$is 2.0 wt%

Plasma polymerized thin film was prepared using an interelectrod inductively coupled gas-flow-type reactor. Styrene was chosen as the monomer to be used. This thin films were also delineated by the electron-beam apparatus with an acceleration voltage 30kV, and the pattern in the resist was developed with RIE 80 with argon gas mixture ratio, pressure and RF power. The effect of charge of discharge power on growth rate and etching rate of the thin films were studied. The molecular structure of thin films were investigated by FIR and then was discussed in relation to its quality as a resist. In the case of Plasma polymerization, thickness of resist could be controlled by discharge duration and power. Also etch rate is increased as to growing argon gas and RF power with RIE 80.

One of the Principal problems encountered in the use of filer reinforced composites is to establish an active fiber surface to achieve maximum adhesion between resin and fiber surface. Now, we want to develope new process that will overcome the disadvantage of the chemical coupling agent and achieve maximum adhesion at the interface between resin and fiber by active plasma treatment on the glass fiber surface. In this study. we investigated the effect of plasma treatment on the wettability of glans surface .

A SOI technology is promising for micromachining: high temperature operation, the fabrication easiness of sophisticated and 3D microstructures, radiation hardness, integrated sensors etc. This paper describes reviews of SOI technologies, and their applications microsensors and microactuators

This thesis describes the effect of heat treatment on the magnetic properties of Co-bsaed Amorphous. A sample was chosen as basic composition with Co$\_$82//Si$\_$2//B$\_$16/ of zero magnetostriction. It was made by single roll method with quartz orifice 0.5[mmø], Ar gas pressure 0.6 [kg/cm$^2$] and roll speed 28 (m/sec) and atmosphere is ,Ar gas. We obtained the sample of width 2.4(mm), thickness 45[$\mu\textrm{m}$]. Made sample annealed for the improvement of magnetic propertics at at annealing temperature 325,350,375 and 400$^{\circ}C$ and annealing time 15, 30, 45, 60 and 120min respectiveily. Amorphous ribbon of co-based showed high permeab- ility ${\mu}$=8000∼14000, and became improvement of magnetic properties according to anneal ins temperature and time. Especially. Amorphous sample at 325$^{\circ}C$ ,45min appearanced high permeability ${\mu}$=13, 589 at frequency f= 100Hz. and loss factor was reduced at low frequency with rising anneal ins ti me and temperature more annealed sample than basic sample.

A recessed $n^{+}$-p junction diode with the serf-aligned structure is proposed and fabricated by using the polysilicon as an $n^{+}$ diffusion source. The diode structure can be applicable to the emitter-base formation of high performance bipolar device and the $n^{+}$ polysilicon emitter has an important effect on the device characteristics. The considered parameters for the polysilicon formation are the deposition condition $As^{+}$ dose for the doping of the polysilicon, and the annealing using RTP system. The vertical depth profiles of the fabricated diode are obtained by SIMS. The eleotrical characteristics are analyzed in trims of the ideality factor of diode (n), contact resistance arid reverse leakage current. The $As_{+}$ dose for the formation of good junction is current. The $As^{+}$ dose for the formation of goodjunctions is about 1∼2${\times}$$10^{16}$$cm^{-2}$ at given RTA condition ($1100^{\circ}C$, 10 sec). The $n^{+}$-p structure is successfully applied to the self-aligned bipolar device adopting a single polysilicon technology.