현재, Field Emission Display(FED)는 "가느냐 가지 않느냐?,"즉 "To go or not to go?"의 기로에 서있는 것으로 보인다. 이러한 시점을 맞이하여 FED 기술의 개요, 점검과 함께, 현재의 진행 상황, 간단한 전망들을 피력하고자 한다.

The variation of photoluminescence(PL) properties of Si thin films was investigated by changing deposition temperatures, Si-rich silicon oxide films on p-type (100) Si substrate have been fabricated by pulsed laser deposition(PLD) technique using a Nd:YAG laser. During deposition, the substrates were kept at the temperature range of room temperature(RT) to $400^{\circ}C$. After deposition, samples were annealed at $800^{\circ}C$ in nitrogen ambient, Strong Blue PL has been observed on RT-deposited Si nanocrystallites. When the deposition temperature was increased over $100^{\circ}C$, PL intensities abruptly decreased. The experimental results show the growing mechanism of Si nanocrystallites by PLD.

The experimental model of the 8-view stereoscopic display system using the photopolymer-based VHOE is proposed. At first, the VHOE is implemented by angle-multiplexed recording of 8-view's diffraction gratings using the optimized exposure-time scheduling scheme in the photopolymer (HRF-150-100) and then. the VHOE-based 8-view stereoscopic display system is implemented by sequentially synchronizing the incident angles of the reference beam of the VHOE with the 8-view stereo images on the LCD pannel. Accordingly, from some experimental results using 8-view images generated by the toed-in stereo camera system, it is found that 8-view stereo images can be diffracted to eight different directions time-sequentially and there is some disparity between the stereo images.

Poly(3-hexylthiophene) or P3HT based organic thin film transistor (OTFT) array was fabricated on flexible poly carbonate substrates and the electrical characteristics were investigated. As the gate dielectric, a dual layer structure of polyimide-$SiO_2$ was used to improve the roughness of $SiO_2$ surface and further enhancing the device performance and also source-drain electrodes were $O_2$ plasma treated for improvement of the electrical properties, such as drain current and field effect mobility. For the active layer, polymer semiconductor, P3HT layer was printed by contact-printing and spin-coating method. The electrical properties of OTFT devices printed by both methods were evaluated for the comparison. Based on the experiments, P3HT-based OTFT array with field effect mobility of 0.02~0.025 $cm^{2}/V{\cdot}s$ and current modulation (or $I_{on}/I_{off}$ ratio) of $10^{3}\sim10^{4}$ was fabricated.

Degradation characteristics of cathodoluminescence (CL) of ZnS:Ag,Cl phosphor were investigated with measurements of CL and photoluminescence (PL). Phosphoric acid treatment was performed to phosphor particles in order to improve CL degradation of phosphor screen that occurred during panel sealing process, and we will discuss mechanisms of degradation and improvement of luminescence mainly with help of AES (auger electron spectroscopy) analysis.

The effect of $\alpha$-septithiophene (${\alpha}-7T$) layers on the organic light emitting diode(OLED) was studied. The ${\alpha}-7T$ was used for a buffer layer in OLED. Hole injection was investigated and improved emission efficiency. The OLEDs structure can be described as indium tin oxide(ITO)/ buffer layer / hole transporting layer / emitting layer / electron transporting layer / LiF / Al. The hole transporting layer were composed of N,N-diphenyl-N,N-di(3-methylphenyl)-1,1-biphenyl-4,4-diamine(TPD), and N,N-di(naphthalene-1-ly)-N,N-diphenyl-benzidine( ${\alpha}$-NPD). The emitting layer, and electron transporting layer consist of tris(8-hydroxyquinolinato) aluminum($Alq_3$). All organic layer were deposited at a background pressure of less than $10^{-6}$ torr using ultra high vacuum (UHV) system. The ${\alpha}-7T$ layer can substitute the hole blocking layer, and improve hole injection properties.

In generally, the guest-emitter doped system has been reported to give a bright electroluminescence(EL). The purpose of using doped system is to improve for increasing lifetime and efficiency, and tuning multicolor light. This indicates an enhanced electron-hole recombination rate in emitting layer. The purpose of this study is to obtain the high performance EL devices for flat panel display with red emission. We fabricated EL devices using the guest-host system. where DCM derivatives were taken as a dopant. The devices are fabricated in multilayer system with various concentration of the dopant (red light emitting dye). We measured the I-V characteristics and EL spectra from these devices. and we compared with photoluminescence(PL) quantum yield among the DCM derivatives. The emission mechanism of devices is participated in energy transfer. The energy transfer from these hosts to DCM generates luminescence spectra that vary from yellow red to red, depending on DCM derivatives. Absorption and emission spectra of organic materials composing the devices depend on the emission materials doped with the DCM derivatives. We demonstrated that the high EL efficiency can be achieved by doping host material with DCM derivatives and molecular steric structures

A novel ceramic synthesis technique, combustion synthesis, is explored to produce a orange-emitting $SnO_{2}:Eu^{3+}$ phosphors. This technique involves a reaction of metal salts with a citric acid as an organic fuel. The variation of the ratio of citric acid to metal introduces change in reaction temperature and atmosphere of the combustion reaction, which in turn influences crystallinity and luminescence properties of the final products seriously. And, the heat treatment of the as-synthesized product increases its luminescence intensity. Especially, the samples treated at above $1100^{\circ}C$ show a orange-emission peak, which is attributed to the formation of single phase and well-crystallized $SnO_{2}:Eu$ oxides in the rutile structure

The effect of low-temperature ZnO buffer layer has been investigated for the optical properties of ZnO thin films. ZnO buffers and thin films have been deposited using the pulsed laser deposition technique. ZnO buffer layers were grown at $200^{\circ}C$ with various thickness of 0 to 60 nm, followed by raising the substrate temperature to $400^{\circ}C$ to grow $2{\mu}m$ ZnO thin films. The buffer layers could relax stresses induced by the lattice mismatch and different thermal expansion coefficients between ZnO thin films and sapphire substrate. In order to identify the optical properties of ZnO thin films, PL measurement was used. From the results of PL measurement, all the fabricated ZnO thin films with buffer layers have shown intensive UV emission with a narrow linewidth. ZnO thin films with buffer layer of 20 nm have shown the strongest UV emission. It was found that the use of ZnO buffer layer plays an important role to improve the intensive UV emission of the ZnO thin films.

We establish a visible light emission from porous polycrystalline silicon nano structure(PPNS). The PPNS layer are formed on heavily doped n-type Si substrate. 2um thickness of undoped polycrystalline silicon deposited using LPCVD (Low Pressure Chemical Vapor Deposition) anodized in a HF: ethanol(=1:1) as functions of anodizing conditions. And then a PPNS layer thermally oxidized for 1 hr at $900^{\circ}C$. Subsequently, thin metal Au as a top electrode deposited onto the PPNS surface by E-beam evaporator and, in order to establish ohmic contact, an thermally evaporated Al was deposited on the back side of a Si-substrate. When the top electrode biased at +6V, the electron emission observed in a PPNS which caused by field-induces electron emission through the top metal. Among the PPNSs as functions of anodization conditions, the PPNS anodized at a current density of $10mA/cm^{2}$ for 20 sec has a lower turn-on voltage and a higher emission current. Furthermore, the behavior of electron emission is uniformly maintained.

박막 다이오드의 전기적 특성에 미치는 전극 구조의 영향을 관찰하였다. 박막 다이오드는 하부전극-절연층($Ta_{2}O_{5}$)-상부전극의 3층 구조로 설계 및 제작하였고, 하부 전극으로 Ta, 상부 전극으로 Cr 및 Ti를 각각 사용하였다. Cr을 상부 전극으로 사용한 결과 비대칭비가 1.8인 높은 비대칭 특성을 나타내었다. 그러나 Ti 상부 전극의 경우 반대의 경향을 나타내었다. 이들을 각각 $150^{\circ}C$에서 열처리한 결과 Cr 상부 전극 다이오드는 비대칭비가 1.4로 여전히 비대칭 경향을 나타내었으나, Ti 상부 전극의 박막 다이오드는 비대칭비가 1.1로 대칭에 가까운 우수한 특성을 나타내었다.

In order to enhence the photocurrent multiplication process, we controlled the irradiation light and the material of cathode layer of organic light emitting diodes (OLEDs). The structures of OLEDs were indium tin oxaide (ITO)/ copper(II) phthalocyanine (CuPc)/triphenyl-diamine (TPD)/ tris-(8-hydroxyquinoline)aluminum (Alq3)/ aluminum (Al). We found that OLEDs were changed by the photocurrent and free charge carrier multiplication process due to the irradiation of light. The rate of photocurrent was increased by the irradiation of red and blue light.

The chalcogenide glasses of thin films have the superior property of photoinduced anisotrophy(PA). In this study, we observed the linear dichroism(D) using the irradiation with polarized He-Ne laser light, in the $Ag/As_{10}Ge_{10}Se_{15}S_{35}$ multi-layer. Mutilayer structures formed by alternating metal(Ag) and chalcogenide($As_{10}Ge_{10}Se_{15}S_{35}$). The Ag polarized photodoping result in reducing time of saturation anisotrophy and increasing sensitivity of linearly anisotrophy intensity, up to maximum 220%. In the thin films of chalcogenide, the Ag polarized photodoping will be show a capability of new method that suggested more improvement of photoinduced anisotrophy property.

We have carried out two-beam interference experiments to form holographic gratings on chalcogenide $Ag/As_{40}Se_{15}S_{35}Ge_{10}$ multi-layer. In this study, holographic gratings have been formed using He-Ne laser(632.8nm) under different polarization combinations(intensity polarization holography, phase polarization holography). The diffraction efficiency was obtained by +1st order intensity and formed grating structure was investigated using atomic force microscopy.

Carbon nano tubes(CNTs) have been reported as field emission source because has a sharp tip, a high aspect tip, high chemical stability, high mechanical strength and low work function properties. In this study, we fabricated successfully the back-lamp of the I-inch flat type using CNTs, which was grown directly on cathode substrate of sodalime glass at low temperature. The brightness of CNT back-lamp is measured to $14 Kcd/m^{2}$ at $2000V_{dc}$ in spacing of $500{\mu}m$. And, the emission properties of packaged CNT back-lamp was analyzed as function of applying voltage and times.

원자층증착법으로 제조한 청색 CaS:Pb 박막 형광체에 대한 열처리 및 전자빔 조사 효과찰 연구하였다. CaS:Pb 형광 박박의 열처리는 500 - $700^{\circ}C$ 온도범위에서 급속 열처리 공정으로 수행하였고, 1 kV, $20{\mu}A/cm^{2}$ 조건의 전자빔을 연속적으로 조사하여 열화를 가속시킨 후 처리 전, 후의 재료 및 cathololuminescence (CL) 특성을 비교 분석하였다. 원자층증착법으로 성장한 CaS:Pb 박막은 화학적 조성과 결정성이 우수하여 후속 열처리에 의해 발광특성이 크게 증가하는 경향을 보이지 않았으며, 전자빔에 의한 열화 정도는 판매되고 있는 형광체에 비하여 오히려 적었다. CL 강도가 초기값의 50%로 감소할 때까지 전자빔을 조사한 후에도 주목할만한 결정성 및 조성의 변화는 관찰되지 않았으나 전자빔 조사에 의해 표변에 두께 10 nm 내외의 탄소오염층이 형성됨을 알 수 있었다.

We analyzed the excitation coefficients and the extinction ratio as a function of waveguide width, center to center distance, and angle of input waveguide for a directional coupler. The variation of thc difference between excitation coefficients is similar to that of the extinction ratio. Also, the smaller the difference between those is, the better the extinction ratio is. This concept will have application to devices using optical coupling.

The beam splitter is important in optical communication systems. in this work, thc quasi-state based on four-mode interference in thc MMI coupler is proposed, and so, device length is shorten to be 1/5 of general designed length. We designed thc polarization splitter based on thc concept of quasi-state. Thc analysis has been accomplished by thc effective index method(EIM) and thc mode propagation analysis(MPA) for given structure.

We report on the polarization-insensitive design and fabrication of an arrayed waveguide gratings (AWG's) using sol-gel derived silica glass films formed on fused silica substrates to provide cheap and stable tools for better design. An arrayed-waveguide grating multiplexer with raised structure is fabricated in order to effect polarization sensitivity. Since polarization is usually not known after propagation in an optical fiber. passive WDM components such as monolithic wavelength demultiplexer have to be polarization insensitive. Here, we observed that polarization have effect on crosstalk of output spectrum in arrayed-waveguide grating

We have demonstrated all-opticalflip-flop based on optical bistability in a SOA/DFB-SOA with broadband gain. Input signal with the wavelength of 1340.23 nm or 1680.93 nm and the current of about 98% of the lasing threshold is injected into theDFB-SOA. Current injected into SOA is 80 mA All-optical flip-flop has various applications such as all-optical memory, demultiplexing, packet-header buffering, and retiming.

Optical bistability can be applied to the optical logic. optical signal processing and optical memory. We have measured the optical bistability of DFB-SOA and demonstrated all-optical OR logic gate using switching characteristics of DFB-SOA.

We have studied the dependence of current-voltage characteristics of Organic Light Emitting Diodes(OLEDs) on temperature-dependent variation. The OLEDs have been based on the molecular compounds. N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1, 1'- biphenyl-4, 4'-diamine (TPD) as a hole transport. tris(8-hydroxyquinolinoline) aluminum (III) ($Alq_3$) as an electron transport and Poly(3,4-ethylenedioxythiophene) (PEDOT:PSS) as a buffer layer. The current-voltage characteristics were measured in the temperature range of 10K and 300K. A conduction mechanism in OLEDs has been interpreted in terms of space-charge-limited current(SCLC) and tunneling region.Ā᐀會Ā᐀衅?⨀頱岒ᄀĀ저會Ā저?⨀⡌ឫഀĀ᐀會Ā᐀㡆?⨀쁌ឫഀĀ᐀會Ā᐀遆?⨀郞ග瀀ꀏ會Ā?⨀〲岒ऀĀ᐀會Ā᐀䁇?⨀젲岒Ā㰀會Ā㰀顇?⨀끩Ā㈀會Ā㈀?⨀䡪ഀĀ᐀會Ā᐀䡈?⨀Ā᐀會Ā᐀ꁈ?⨀硫Ā저會Ā저?⨀샟ගऀĀ저會Ā저偉?⨀栰岒ഀĀ저會Ā저ꡉ?⨀1岒ഀĀ저會Ā저J?⨀惝ග؀Ā؀會Ā؀塊?⨀ග䈀Ā切

Electro-optical (EO) characteristics of the ion beam (IB) aligned twisted nematic (TN)-liquid crystal display (LCD) with oblique ion beam exposure on the diamond-like carbon (DLC) thin film surface were studied. An excellent voltage-transmittance (V-T) curve of the ion beam aligned IN-LCD was observed with oblique ion beam exposure on the DLC thin film surface for I min. Also, a faster response time for the ion beam aligned TN-LCD with oblique ion beam exposure on the DLC thin film surface for 1 min can be achieved.

Fast response characteristics of twisted nematic liquid crystal display (TN-LCD) cell with different nematic liquid crystals (NLCs) and cell gap on a rubbed polyimide (PI) surface were studied. High transmittance and fast response time of the TN-LCD on the rubbed PI surface were achieved by using high birefringence ($\Delta$ n) and low cell gap. It is considered that the transmittance and response time of the TN-LCD on the rubbed PI surface decreased as $\Delta$ nd decrease.

In this study, The cathode interface layer (CIL) was investigated using aromatic diamine derivatives. Cz-TPD (4,4'-biscarbazolyl(9)-biphenyl) used in the cathode interface layers is investigated emition charcaracteristics at the green organic electroluminescent devices. TPD (N,N' -dyphenyl -N -N'-bis (3-methy phenyl)-1,1' -biphenyl-4,4' -diamine) as the hole transformer layer and $Alq_{3}:tris$ (8-hyd-roxyquinoline) aluminium) as the electron transport layer and emiting layer maded use of the organic electroluminescent device. The Organic Electroluminescent Device with Ag cathode and CIL of Cz-TPD(4,4'-biscarbazolyl(9)-biphenyl) showed good EL characteristics compare to a conventional Mg:Ag device and also an improved storage stability. [1] As the change in MgAg, Cz-TPD/Ag, Ag at the chthode, the electrical and optical charcaracteriseics were investigated.

연성 AI 전극을 이용하여 플라스틱 기판 위에 대칭성 박막 다이오드를 제작하였다. 다이오드의 구조는 $Al/Ta_{2}O_{5}/Al$의 3층 구조로 되어 있다 상부 AI 전극 제작시 하부 AI 전극의 손상을 방지하기 위해 무(無)식각 공정을 개발, 적용하였다. AI 전극을 사용한 결과 단단한 Ta 전각에서 나타난 변형 빛 균열 문제가 해결되었다. 또한 상부 빛 하부의 대칭성 전극 구조로 제작함으로써 I-V 곡선이 완벽한 대칭형의 우수한 전기적 특성을 얻을 수 있었다.

In this paper, a new method to implement the photopolymer-based VHOE using the optimized exposure time schedule is proposed. The cumulative grating strength dependence on the exposure energy is mathematically modeled by using the fourth-order polynomial function and then using this model, the optimized exposure-time schedule of the photopolymer for recording the given multiple gratings is calculated.

투과형 광 시야각 모드의 하나인 Fringe Field Switching (FFS) mode를 반사형 액정 디스플레이소자로 응용하여 전기 광학적 특성을 컴퓨터 시늉 하였다. FFS mode는 액정이 수평으로 균일하게 유지되면서 구동하므로, 시야각에 따른 굴절률 변화 역시 균일하게 유지된다. 이러한 특성 때문에 반사형 FFS mode는 부가적인 위상필름을 쓰지 않고, 액정층과 편광판 1매 만으로도 일정한 수준의 반사형 디스플레이 특성을 얻을 수 있다. 컴퓨터 시늉을 통해 1매 편광판과 액정층, 반사판으로 구성된 Normally Black모드의 셀 구조를 취하고, 셀 간격을 일정하게 유지하면서 액정의 ${\Delta}n$을 변화시켜 특성을 구하는 방식으로 수행하여, 입사광의 파장이 550nm일때 최적의 셀 위상차값으로 $d{\Delta}n$인 $0.1365{\mu}m$를 얻었다. 입사광원을 $0^{\circ}C$로 하고 편광판 투과율이 41%였을 때 정면 반사율은 on시 33.6%, off시 0.14%로 명암대비가 233:1이었다. 특히 시야각은 극각 $60^{\circ}C$이내의 전 방향에서 명암 대비비가 5이상의 특성을 보였다.