This paper presented the effects of accumulation of surface charges on hydrophobicity level and the surface states of silicone polymer used for outdoor insulator treated by ultraviolet irradiation and corona discharge through measuring surface voltage decay of a corona-charged specimen were investigated. The surface resistivity by the method of the surface potential decay was compared with the value by the three electrodes methods. From this study, it was found that the accumulation of surface charges above a critical surface voltage on silicone insulating materials could lead to the temporary loss of surface hydrophobicity. In addtion, uv stress lead to a longer decay time of surface charges. We could conclude that the effects of surface charges on hydrophocity level and the changes of surface state by various artificial treatments were understood through a trend of surface potential decay.

In our country, the housing materials of polymeric outdoor insulators have mainly been used EPDM or silicone rubber. EPDM housing materials had been widely used in the field for the first time. The reason why silicone has the high cost of production. But recently, most of the manufacturers that newly developed polymeric insulators make its choice of silicone housing. EPDM showed a good resistance to tracking. We compared the various characteristics for EPDM and silicone insulators that have similar type and design. Silicone insulators have more performance in flashover voltage test and leakage current measurement because of a good water repellent than EPDM ones. Also, the property of EPDM compared with silicone insulators greatly decreased after aging test in combined acceleration ageing facilities for 1000 hours.

Sintered Cu-W has been used for the electrode of GIS for interrupting the abnormal current. In this study the effect of Ni addition in Cu-W electrode was investigated. Cu-W electrodes used contains 0.1~0.2wt% Ni and were conducted the experiments which was attacked by DC arc test (70V-70A) for 300 times periodically. As the contents of Ni in Cu-W electrode increase, the hardness and electrical conductivity were decreased. The weight change ($\Delta$mg) of electrode after DC arc test increased with increasing Ni contents and test times. The hardness and electrical conductivity of electrode after DC arc test were decreased compared with non-arc affected electrode, which was owing to the defects near surface of electrode and degradation by arc heat. It was considered that Cu in the Cu-W electrode was scattered to all directions by arc heat, therefore, the electrodes were damaged and deformed in the surface and cross-section of electrode. It is difficult to estimate directly the characteristics of Cu-W electrode for GIS related with high voltage and current from the results of DC arc test conducted in this study. However, the results of the effect of Ni addition in Cu-W electrode could be applied for the research of electrode for GIS.

In this paper, We explained the best shape design of electrode for discharge on the water. Electrode with rounding was reduced maximum electric field of over 40% to electrode without rounding for discharge on the water and the best shape of electrode for discharge on the water designed when shape of electrode had a curve radius of over $60^{\circ}$ at electrode's face to electrode's face with minimum distance and a curve radius of under $120^{\circ}$ at electrode's side face to electrode's front face. And When dielectric beads are used between electrodes, the life of electrodes is improved by lower stress of electric field on surface of electrodes.

In this paper, we performed analysis of electric field, magnetic field, current density in AMF electrode using the Maxwell 3D simulation. The current distribution and magnetic field in simple models are analyzed to verify its efficiency and accuracy. In the vicinity of the slits of axial magnetic field type electrode a comparatively high axial magnetic flux density existsIn addition the validity of FEM is confirmed by performing the analyses of distribution in current density and magnetic flux density.

The flat transformer, typically, has a number of parallel single turn secondary windings. Each secondary winding is coupled to the same primary winding. Therefore, the current in each secondary winding is equal to the ampere-turns in the primary winding, and to each other. These characteristics are particularly advantageous where parallel rectifiers are used. The windings share the current equally, with no need for ballast resistors or other added components. In this study, the ferrite magnetic core samples of Mn-Zn system for the Flat transformer are manufactured and the electrical and magnetic characteristics of its tested. The density of sample FO2-2 sintered at $1350^{\circ}C$ is $4.00kg/m^3$, which shows the good microstructural state. The initial permeability and saturation flux density of FO2 at room temperature is 2700 and 510mT, individually. The power loss of FO2 samples at 250kHz have been ranged $350kW/m^3$ to $80kW/m^3$ with temperature. And the minimum power loss of sample FO2-2 showed at $70^{\circ}C$, which property seems very positive to apply for a flat transformer.

옥외 절연물은 환경에 의한 오염과 수분에 의한 젖음 현상이 항상 발생하므로 폴리머 애자의 하우징 재료의 전기방전에 대한 열화내성과 우수한 발수성의 장기간 유지특성은 제품의 장기성능에 있어서 매우 중요한 물성이다. 실리콘 고무는 내열성, 내후성, 산화안정성, 발수성 및 내오염성 동 절연소재로서 우수한 특성을 가지고 있지만 하우징 표변에서의 방전이 발생될 때 옥외절연물에서의 성능은 실리콘 고무의 배합처방에 따라서 많은 차이가 나고 있다. 본 연구에서는 내트래킹 agent인 ATH의 첨가량의 변화에 따른 재료의 특성을 조사하고, 그 특성이 실리콘 고무 폴리머 애자의 특성에 미치는 영향을 조사하였다. ATH의 첨가량에 따라서 내아크성, 내트래킹성 및 표면 발수성을 조사하였고, 폴리머 애자를 내트래킹 휠 시험 및 선행오손 후 섬락전압을 측정하였다.

폴리머 애자의 장기성능예측을 위하여 많은 수단과 측정방법이 연구되어 왔다. 그러나 폴리머 애자에 있어서 성능저하는 대부분 하우징 재료의 열화에 기인되고 있어 예측 및 진단목적의 연구가 하우징 재료의 가속열화에 초점이 맞추어져 있다. 폴리머 애자는 초고압 절연성능과 기계적 강도가 우수하여 송배전 설비에 많이 사용되고 있지만 애자의 형상과 장기성능과의 관계가 정량적으로 규명되어 있지 않아 개발하는 회사는 물론 사용하는 전력회사가 함께 어려움을 가지고 있다. 폴리머 애자의 형상이 폴리머 애자의 장기 성능에 어떻게 영향을 주는 지를 비교분석하고 평가하는 연구가 필요한 시점이다. 본 연구에서는 규칙 교대 갓, 불규칙 교대 갓의 폴리머 애자를 조립방식으로 제작하고, 규칙 교대 갓의 폴리머 애자를 일체형 진공사출 방식으로 제작을 하여 건조섬락전압, 주수섬락전압, 오손섬락전압을 측정하였다. 오손섬락전압은 주수섬락에 비하여 60% 정도 감소함을 보였고 불규칙한 교대 갓의 폴리머 애자의 경우 특성의 편차가 크게 나타났다. 폴리머 애자의 경우 소재의 우수한 특성도 중요하지만 형상적인 인자도 중요한 설계요소이므로 최적화 방안이 요구된다.

An ageing characteristics of RTV coating materials by corona discharge have been studied. The recovery of a hydrophobicity of RTV coating materials with the thickness of $300{\mu}m$ was in identical with a bulk silicone materials. The hydrophobicity of RTV coating materials has been almost lost when its were discharged during 40 seconds by corona with 10kV, and recovered after about 45 hours. But the resistivity of RTV coating materials has not been recovered after 45 hours, even though after 80 hours the 95% of initiation resistivity value has been recovered. There was no critical compounds(such as Si and Al) changes on RTV surfaces by the corona discharge treatment until 100 seconds. In the test of arc erosion, it was seen that the coating sample with silicone rubber as a base material have more longer bum-out time than other samples with FRP or glass base.

전기방전에 대한 shed 재료의 열화내성과 우수한 발수성의 장기간 유지특성은 폴리머 애자의 장기성능에 있어서 가장 중요한 인자들이다. 애자 제조시 무결점 성형성 또한 중요한데 열화내성을 확보하기 위해 다량의 ATH의 첨가가 수반되기 때문에 적절한 process oil의 사용이 불가피하다. 사용하는 오일의 종류와 량에 따라 옥외절연물의 장기성능에 영향을 주는 표면발수성이나 방전내성은 크게 차이가 나는 것으로 밝혀지고 있다. 본 논문에서는 화학적 구조와 정도가 다른 몇 가지 실리콘 fluid들을 실리콘 고무에 처방하여 기본물성과 초고압 옥외절연물의 shed 재료로서 장기성능에 영향을 주는 방전열화내성과 표면발수성의 회복특성을 평가하였다. 실리콘 고무의 무결점 사출성형에 가소도가 중요한데 동일한 무기물 첨가조건에서 유사한 가소도를 갖게 하는데 필요한 량은 fluid들의 종류에 따라서 상당한 차이가 있었다. 특히 PDMS는 점도는 낮지만 분자량이 커서 많은 량이 첨가되어 기계적 특성저하가 크게 일어났다. 코로나 처리후 발수성 회복특성은 fluid들의 분자크기와 반응기의 종류에 따라 상당히 영향을 받았으며 분자가 클수록 초기회복속도는 다소 느려도 최종의 상시발수성은 다소 높게 유지되었으며 2일 이내에 거의 초기 접촉각으로 회복되었다. 내아크성은 무게손실이 적을수록 오차범위도 작은 안정된 특성을 보였으며 fluid들의 종류에 따른 무게손실의 차이는 크지 않았다. 트래킹 방전에 의한 무게 감소는 fluid의 분자가 크면서 페닐기를 가진 fluid들이 첨가된 고무가 우수한 특성을 보였다.

할로겐 난연재료 및 고분자의 연소시 Dioxine의 문제점이 대두되고 있어 유럽국가를 중심으로 할로겐 난연제 사용을 규제하고 있다. 환경과 인체에 대한 안정성을 고려해서 저 유해 가스화, 저 발연화, 저 부식성, 리사이클링 등을 겸비한 제품의 개발로 관심이 모아지고 있는 실정이다. 본 연구에서는 환경친화적인 금속화합(수산화 알루미늄)을 사용하여 연소시 발생할 수 있는 난연성, 무독성, 소연성 등을 함량별로 확인하고 난연재가 증가할수록 취약한 기계적 물성 보완을 위해 moisture cure crosslikable 기술로 케이블절연 및 자켓 피복층 특성을 증가 시켰다. 그러나 수산화알루미늄 함량이 증가할수록 기계적 물성과 기타 특성도 감소하는 경향을 보이고 있어 최적의 난연제 조성함량이 약 130~150 phr정도에서 우수한 결과를 확인하였다. 또한 moisture cure agent는 전선압출 시 표면에 scorch 및 장기 압출에 영향을 주므로 약 1.5~2phr 범위에서 처방하는 것이 우수하다. 원료투입 후 mixing 공정 중에서는 온도관리가 매우 중요하므로 되도록 믹싱 온도를 $130^{\circ}C$ 이하를 유지해야한다. 온도는 수산화알루미늄의 분산성과 케이블 피복압출 시 표면에도 영향을 주기 때문이다 본 연구는 이런 작업방법을 통해 친환경 가교 난연콤파운드가 비(比) 가교된 제품에 비해 특성이 증가되는 것을 입증할 수 있었다.

The performance of insulators under contaminated conditions is the underlying and the most factor that determines insulation design for outdoor applications, Among the contamination factors, The sea salt is the most dangerous factor, and the salt factor have closed relation with climatic conditions, such as wind, temperature, humidity and so on, Effect of these factors to insulation system is different of each other, and need to show the correlation by multiple regression analysis techniques. In this paper, predicted and analyzed equivalent salt deposit density (ESDD) by change climatic condition through multiple regression analysis.

In this paper we investigated electrical properties for epoxy resin with improved mechanical property, elastomer epoxy. Investigated electrical properties are permittivity, tan $\delta$ and breakdown voltage strength(BDV). Permittivity and tan $\delta$ have dependancy on additive Quantity in general purpose epoxy resin. In particularly, those have very high values at low frequency and high temperature according to increasing component of elastomer. In case of BDV test, those materials have only a little difference due to increasing elastomer components. But in case of high quantities of elastomer, BDV has a difference. These results are represented that elastomer epoxy resin despite superior mechanical property needs many carefully thought as application electrical insulation.

This paper explained electric field distribution's characteristics of dielectric pellets with a shape of ball to voltage. When discharge gap of electrode and input voltage are each 20[mm], 10000[V], the electric field simulation results of dielectric pellets with a shape of ball with relative dielectric constant of several kind measured stronger electric field near electric pellets with a shape of ball of ${\phi}5$[mm] than $1{\phi}$[mm] and $3.33{\phi}$[mm] at atmosphere. And the maximum electric field of dielectric pellets with a shape of ball over ${\phi}5$[mm] increased about 5[%] to maximum electric field of electric pellets with a shape of ball ${\phi}5$[mm]. And the result of simulation, when relative dielectric constant of dielectric pellets with a shape of ball is 100, it measured about 90[%] of maximum electric field of dielectric pellets with a shape of ball with relative dielectric constant over 1000.

In the response to an increasing demand for electrical energy, much effort aimed to develop and commercialise HTS power equipments is going on around the world. For the development, it is necessary to establish the dielectric technology in $LN_2$. Hence many types of dielectric tests should be carried out to understand the dielectric phenomena at cryogenic temperature and to gather various dielectric data. Among the many types dielectric tests, the barrier effect were conducted with the simulated electrode after analysing the insulating configuration of the pancake coil type HTS transformer. The influence of a barrier on the dielectric strength was measured according to the size and the position of the barrier. It was shown that the effectiveness, the ratio of the breakdown voltage in presence of barrier to the voltage without barrier, is highest when the barrier is placed at the needle electrode side. And the barrier effect was not depend on the electrode array. The life time to breakdown with decreasing the applied voltage was increased remarkably having wide error band but the shape parameter in Weibull distribution was almost constant.

In this paper, we researched breakdown characteristics of paper/liquid nitrogen composite insulation system for application of a high temperature superconducting cable. And, we have studied the AC breakdown performance of paper/ice composite insulating system immersed in liquid nitrogen. The electric strength in this paper/ice composite system is higher than that of paper/liquid nitrogen system. Furthermore this system shows a self-healing type breakdown behavior. Among the many kinds of liquid to be immersed and frozen to the ice, deionized water gives the highest electric breakdown strength. The paper/ice composite insulation system is thought to be one of good candidate for the electrical insulating system at cryogenic temperature.

This paper describes the information for the difference between two-term and multi-term approximation of the Boltzmann. In previous paper, we calculated the electron transport coefficients in pure Oxygen and Argon gases by using two-term approximation of Boltzmann equation. Therefore, in this paper, we calculated the electron transport coefficients(W and $N{\cdot}D_L$) in pure Oxygen and Argon gases for range of E/N values from 0.01~500[Td] at the temperature was 300[K] and pressure was 1[Torr] by using multi-term approximation of the Boltzmann equation by Robson and Ness, The results of two-term and multi-term approximation of the Boltzmann equation has been compared with the experimental data for a range of E/N.

This paper describes the information for quantitative simulation of weakly ionized plasma. In previous paper, we calculated the electron transport coefficients in pure Xenon gas by using two-term approximation of Boltzmann equation. Therefore, in this paper, we calculated the electron transport coefficients(W, $N{\cdot}D_L$ and $D_{L/{\mu}}$) in pure Xenon gas for range of E/N values from 0.01 ~ 500[Td] at the temperature was 300[K] and pressure was 1[Torr] by using multi-term approximation of the Boltzmann equation by Robson and Ness, The results of two-term and multi-term approximation of the Boltzmann equation has been compared with the experimental data by L. S. Frost and A. V. Phelps for a range of E/N.

MEMS(Micro Electro Mechanical System) 기술에서 실리콘 식각기술의 중요성으로 플라즈마 식각기술의 개발이 꾸준히 진행되고 있다. 이중에서 ICP(Inductive Coupled Plasma)는 기존의 증착장치에 유도결합식 플라즈마를 추가로 발생시켜 증착막의 특성을 획기적으로 개선시키는 가장 최근에 개발된 기술이며, 이용에너지를 증가시키지 않고도 이용밀도를 높이고 이용업자들에 방향성을 가할 수 있는 새로운 플라즈마 기술로, 주로 MEMS 제조공정에 응용되고 있다. 본 연구에서는 STS-ICP $ASE^{HR}$을 이용하여 식각과 증착공정을 반복하여 식각을 하는 Bosch 식각에 관하여 연구하였다 STS-ICP $ASE^{HR}$ 장비의 Platen power, Coil power 및 Process pressure에 다양한 변화를 주어 각 변수에 따른 식각속도를 관찰하였다. 각 공정별 변수를 변화시킨 결과 Platen power 12W, Coil power 500W, 식각/Passivation Cycle 6/7sec 일 경우 식각속도는 $1.2{\mu}m$/min 이었고, Sidewall profile은 $90{\pm}0.7^{\circ}$로 나타나 매우 우수한 결과를 보였다.

유도결합형 플라즈마(Inductively coupled plasma)는 조명기술 분야에서도 효과적인 방전 소스로 이용되고 있다. 이중 무전극 램프에서의 유도결합형 플라즈마의 이용은 장수명은 물론 높은 효율과 넓은 동작 온도특성, 전원 인가시와 동시에 방전이 개시되는 등 여러 가지 장점을 가지고 있다. 본 논문에서는 Re-entr-ant Type QL-lamp에 사용되어진 페라이트의 형태에 변화를 주어 이에 따른 전자계 특성을 살펴보았다. 먼저 페라이트 코어의 특성에 따른 임의의 영역에서의 자속 및 자속밀도 그리고 자계강도 등을 고려하였으며, 시뮬레이션을 통한 페라이트 크기의 변화에 따른 전자계 분포 특성을 조사하였다.

In this study, porcelain insulator samples which have a different alumina composition were manufactured in order to test electrical and mechanical properties and make an analysis of the propagation phenomena of micro cracks on porcelain body. From XRD quantitative analysis the crystalline phases were different with alumina composition, sample C and D which have about 17wt% Corundum phase without the Cristobalite phase shows better electrical and mechanical properties than sample A and 8 which have the Cristobalite phase. In dielectrics test on porcelain samples with below 17wt% alumina composition, it was found that the amount of glass phase$(SiO_2)$have an main effect to decrease the dielectric loss$(tan{\delta})$, and the dielectric breakdown voltage of aluminous porcelain insulators was largely affected by its relative density. As a micro cracks analysis, HRS were measured, then the intensity of HRS increased with the amount of alumina composition. On the other hand, the propagation behaviors of cracks was fairly influenced by the distribution of pores.

In this paper, using a Langmuir probe Ar gas characteristic of electrodeless fluorescent lamp which used an inductively coupled plasma were investigated. The RF output changed into 5-50W in 13.56MHz. At this time internal plasma voltage of the chamber and probe current were measured while changing in -70V - +70V with a supply voltage by Langmuir probe. If pressure of Ar gas was increased, the electric current tended to decrease. Also, an electric current was increased according to an increase of a RF output.

In this paper, the emission properties of electrodeless fluorescent lamp were discussed using the inductively coupled plasma. To transmit the electromagnetic energy into the chamber, a RF power of 13.56MHz was applied to the antenna and considering the Ar gas pressure and the RF electric power change, the emission spectrum, Ar-I line, luminance were investigated. At this time the input parameter for ICP RF plasma, Ar gas pressure and RF power were applied in the range of 10~60m Torr, 10~300W respectively.

In this dissertation the results of the combined experimental and theoretical studies designed to understand and predict the spatial growth and transport coefficients for electrons in $SF_6$ and $SF_6$-Ar mixtures have described. The transport coefficients for electrons in (0.1[%])$SF_6$-Ar, (0.5[%])$SF_6$-Ar, (1.0[%])$SF_6$-Ar, (3.0[%])$SF_6$-Ar and (5.0[%])$SF_6$-Ar mixtures were measured by time-of-flight method, and the electron energy distribution function and the parameters of the velocity and the diffusion were determined by the variation of the collision cross-sections with energy.

고휘도 LED(light emitting diode) 빨강(R), 녹색(G), 파랑(B), 호박색(A), 백색(W) 등의 중요한 광학특성인 광속(luminous flux), 효율(luminous efficacy), 피크 파장(peak wavelength), 가중치 평균 파장(weighted average wavelength), 반치폭 (full width at ha1f maximum), 색도좌표(chromaticity coordinate), 주 파장(dominant wavelength), 자극순도 (excitation purity) 와 휘도순도(colorimetric purity)에 대해서 비교검토하였다. 시험결과로 제시된 LED의 기본적인 특성 데이터는 추후, 새로운 조명용 LED 램프나 등기구(luminaire)를 개발 및 특성연구에 많은 도움을 줄 것으로 사료된다.

The ageing cause in many porcelain suspension insulators which occur on transmission and distribution line with dead-end stings is mechanical stress in interface between porcelain and cement materials. It is known that the principal mechanical stress which give electrical failure is the results of the displacement is due to cement growth. We studied an analysing method to find out a deformation of brittle porcelain with a thermal expansion of cement for suspension insulator. These simulation analysis and experimental results show that cement volume growths affect severely to be mechanical failure ageing. These simulation analysis and experimental results show that axial loading affects of Porcelain insulators severely to be mechanical failure ageing.

The main objective of this paper is to module design and pressure relief test a new type of polymer gapless surge arrester for power distribution line. Metal oxide surge arrester for most electric power system applications, power distribution line and electric train are now being used extensively to protect overvoltage due to lightning. Surge arresters with porcelain housing must not have explosive breakage of the housing to minimize damage to other equipment when subjected to internal high short circuit current. When breakdown of gapless elements in a surge arrester occurs due to flashover, fault short current flows through the arrester and internal pressure of the arrester rises. The pressure rise can usually be limited by fitting a pressure relief diaphragm and transferring the arc from the inside to the outside of the housing. However, there is possibility of porcelain fragmentation caused by the thermal shock, pressure rise, etc. Non-fragmenting of the housing is the most desired way to prevent damage to other equipment. The pressure change which is occurred by flashover become discharge energy. This discharge energy raises to damage arrester housing and arrester housing is dispersed as small fragment. Therefore, the pressure relief design is requested to obstruct housing dispersion.