Recently, because GIS equipment has problems on confidence according to long-time usage, development of diagnosis technique has been importantly recognized. Therefore. measurement and analysis of PD has been generally used much equipment of GIS. But, in case of measurement of PD at field, real trouble signals are difficult to classify noise. Accordingly, a variety of trouble conditions for DS were simulated, and detected signals were analyzed by the application of electrical and mechanical methods. For this anslysis, detected signals were accumulated according to phase-magnitude with the application of Induction sensor, and then we analyzed the characteristics. For the simulation experiment, we made DS for 170kV GIS and analyzed the characteristics of detected singals with the application of neural network algorithm.

We have investigated equivalent-circuit analysis of organic light-emitting diodes using frequency-dependent response of $ITO/Alq_3(60nm)/Al$ device at two different bias voltages. Complex impedance Z of the device was measured in the frequency range of 40Hz~1MHz. A Cole-Cole plot shows that there are two dielectric relaxations at the bias below turn-on voltage, and one relaxation at the bias above turn-on voltage. We are able to interpret the frequency-dependent response in terms of equivalent-circuit model of contact resistance $R_s$ in series with parallel combination of resistance $R_p$ and capacitance $C_p$. We have obtained contact resistance $R_s$ around $90{\Omega}$, mainly from the ITO anode.

In this study, we investigated about electrooptics characteristic of three kind of TN cell on the polyimide surface. Monodomain alignments of thermal stressed TN cell over temperature of liquid crystal isotropic phase were almost same that of no thermal stressed TN cells. However, the thermal stressed TN cell have many defects. Also, threshold voltage and response time of thermal stressed TN cells show same performances of no thermal stressed TN cells. There were little changes of value in these TN cells. However, transmittances of TN cells on the polyimide surface decrease with increasing thermal stress time. Finally, the residual DC voltage of the thermal stressed TN cell on the polyimide surface show decrease of characteristics as increasing thermal stress time. Therefore, thermal stability of TN cell was decreased by high thermal stress for the long times.

펜틸시아노비페놀(PCB) 액정셀은 저주파 영역에서 유전율이 대단히 크게 나타나는 현상이 보인다. 그 원인은 액정셀 내의 불순물 이온의 거동이라고 생각된다. 액정셀 내에 존재하는 불순물 이온의 거동을 관찰하기 위하여 PCB 액정셀의 유전 분산특성을 측정하여 온도의존성, 막 두께 의존성, 직류전압 의존성등을 측정하였다.

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using thin plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. The NLC pretilt angles generated are about $3^{\circ}$ by the rubbing alignment method on thin plastic substrates, However, the pretilt angle are at about $1.7^{\circ}$ lower on the glass substrate than on thin plastic substrate. Also, EO characteristics of the TN-LCD with a rubbed PI surface based on polymer are almost the same as that of the TN-LCD with a rubbed PI surface based on glass. However, the transmittances of the TN-LCD with a rubbed PI surface based on polymer is less than that with a rubbed PI surface based on glass.

We studied the nematic liquid crystal (NLC) aligning capabilities using the new alignment material of a Carbon Nitride (NDLC) thin film. NDLC thin film exhibits high electrical resistivity and thermal conductivity that are similar to the properties shown by diamond-like carbon (DLC) thin films. The diamond-like properties and nondiamond-like bonding make NDLC an attractive candidate for applications. A high pretilt angle of about $9.9^{\circ}$ by ion beam (IB) exposure on the NDLC thin film surface was measured. A good LC alignment is achieved by the IB alignment method on the NDLC thin film surface at annealing temperature of $200^{\circ}C$. The alignment defect of the NLC was observed above annealing temperature of $250^{\circ}C$. Consequently, the high pretilt angle and the good LC alignment by the IB alignment method on the NDLC thin film surface can be achieved.

Different types of hybrid negative materials on pitch based carbon and natural graphite for lithium ion batteries were studied. Two types of active materials were prepared, that is, pitch based graphite carbon, and pitch based carbon impregnating natural graphite. The specific capacity, capacity recovery in high temperature condition, and other electrochemical properties were achieved for these materials. We found that addition of natural graphite type to the pitch based carbon can significant1y improve the specific capacity and interfacial resistance. However, use of natural graphite will cause a serious capacity loss in the high temperature condition owing to its increasing interface resistance. The specific capacity ranged from 321 to 348 mAh/g and the maximum specific capacity was obtained in the case of pitch based carbon impregnating natural graphite.

During the last 20 years organic semiconductors have attracted considerable attention due to their interesting physical properties followed by various technological applications in the area of electronics and opto-electronics. It has been a long time since organic solar cells were expected as a low-cost energy-conversion device. Although practical use of them has not been achieved, technological progress continues. Morphology of the materials, organic/inorganic interface, metal cathodes, molecular packing and structural properties of the donor and acceptor layers are essential for photovoltaic response. We have fabricated solar cell devices based on zinc-phthalocyanine(ZnPc) as donor(D) and fullerine$(C_{60})$ as electron acceptor(A) with doped charge transport layers, $Alq_3$ as an electron transport or injection layer. We observed the photovoltaic characteristics of the solar celt devices using the Xe lamp as a light source.

Ozone is useful oxidizing gas for the fabrication of oxide thin films. Accordingly researching on oxidizing gas is required. In order to obtain high quality oxide thin films, higher ozone concentration is necessary. In this paper oxidation property was evaluated relation between oxide gas pressure and inverse temperature(CuO reaction). The obtained condition was formulated by the fabrication of Cu metal thin film by co-deposition using the Ion Beam Sputtering method. Because the CuO phase peak appeared at the XRD evaluation of the CuO thin film using ozone gas, this study has succeeded in the fabrication of the CuO phase at $825^{\circ}C$.

The $Bi_2Sr_2Ca_nCu_{n+1}O_x$ superconducting thin film fabricated by using the sputtering method was compared with the $Bi_2Sr_2Ca_nCu_{n+1}O_x$ superconducting thin film fabricated by using the evaporation method. In doing the ultra-low deposition because each element can exist on the substrate surface, both the sputtering method and the evaporation method could easily fabricate single phase of the Bi2212 phase. Also, it is cofirmed that by optimizing the deposition condition, each single phase of the Bi2201 phase and the Bi2212 phase can be fabricated, the sticking coefficient of Bi element is clearly related to the changing of substrate temperature and the formation of the Bi2212 phase.

CuPc와 $C_{60}$을 이용하여 ITO/CuPc/Al의 CuPc 단층구조와 $ITO/CuPc/C_{60}/Al$의 이종접합 구조에서의 광기전 특성을 연구하였다. CuPc 단층구조에서는 CuPc층의 두께를 10nm에서 50nm로 가변하여 전압-전류 특성을 측정한 결과 40nm 부근에서 최적화된 전기적인 특성이 나타났으며, $CUPC/C_{60}$의 이종접합 구조에서는 CuPc와 $C_{60}$의 두께 비율을 1 : 1 (20nm : 20nm), 1 : 2 (20nm : 40nm), 1 : 3 (20nm : 60nm)으로 가변하여 측정한 결과, 1 : 2의 두께비에서 최적화된 특성을 얻었다. 광원은 500W Xe lamp(ORIEL 66021)를 이용하였으며, 광원의 세기는 보정된 radiometer/photometer (International Inc. IL14004)와 Si-photodiode로 측정하였다.

The aspherical lens are used as objective lens of optical pickup. The sample product is made before manufacturing the injection mould of lens to examine the design factor. The optimum cutting conditions of the main spindle speed, the depth of cut, the feed rate are found when we cut PMMA and PC lens sample with ultra-precision SPDT. The demanded surface roughness 10 nm Ra, aspherical form error 0.5 ${\mu}m$ P-V for aspherical lens of optical data storage device are satisfied for PMMA, but not satisfied for PC.

The movement of electron in the semiconductor-gap-semiconductor was observed by the variation of V-I characteristic as a distance two ZnO(1010) single crystals. When the resistance between two crystals was $10^2{\sim}10^4{\Omega}$, V-I characteristics had the pattern of the field emission or ohmic contact. On the other hand, when the resistance was larger than $10^7{\Omega}$ by increasing the distance between two crystals, the effect of surface barrier was prominent. This result leads to the conclusion that both the field emission (or ohmic contact) and the surface barrier effect including the tunneling have the influence on V-I characteristics of mechanically contacted crystals.