The electric power demand is steadily high. It becomes difficult to secure the land for overhead transmission lines year after year. Downsizing of overhead transmission lines can be most effectively achieved by applying polymer insulation arm. This paper describes the outline of compact overhead transmission lines and the result of mechanical evaluation of FRP for the compact transmission towers. Bending strength of FRP was evaluated according to the fiber orientation because the fiber orientation in FRP has a great effect on the strength of FRP.

$LiFePO_4$ is a potential candidate for the cathode material of the lithium polymer batteries. $LiFePO_4$ cathode active materials were synthesized by coating on the $LiFePO_4$ was tried using $TiO_2$ and corbon in oreder to increase cyclic performance and electronic conductivity. Highly dispersed on the particles enhances the electronic conductivity and increases the capacity. For lithium polymer battery applications, $LiFePO_4$/SPE/Li and $LiFePO_4$-$TiO_2$/SPE/Li 'cells were characterized electrochemically by cyclic volatammetry and charge/discharge cycling. The $LiFePO_4$-carbon-$TiO_2$ cathode in PVDF-PC-EC-$LiCIO_4$ electrolyte showed high capacity at high current density.

Zinc Oxide(ZnO) thin films on Si (100) substrates were deposited by RF magnetron reactive sputtering. The characteristics of zinc oxide thin films with changing sputtering conditions such as argon/oxygen gas ratios, RF power, and substrate temperature, chamber pressure and target-substrate distance were investigated. To analyze a crystallographic properties of the films, $\theta/2{\theta}$ mode X -ray diffraction, SEM, and AFM analyses. C-axis preferred orientation, resistivity, and surface roughness highly depended on Ar/$O_2$ gas ratios. The resistivity of ZnO thin films rapidly increased with increasing oxygen ratio and the resistivity value of $9{\times}10^7\;{\Omega}cm$ was obtained at a working pressure of 10 mTorr with Ar/$O_2$=50/50. The surface roughness was also improved with increasing oxygen ratio and the ZnO films deposited with Ar/$O_2$=50/50 showed the excellent roughness value of $28.7{\AA}$.

As a display becomes large recently, Acquisition of high luminance and Luminance uniformity is becoming difficult in the existing CCFL or EEFL backlight system. So, study for a performance enhancement has enforced. but lamp development of flat type is asked for high luminance and a luminance uniformity security in of LCD and area anger trend ultimately. In this paper, we changed a tip shape of an electrode for production by the most suitable LCD backlight surface light source, and confirmed discharge characteristic along discharge gas pressure and voltage, and confirmed electric field distribution and discharge energy characteristic through a Maxwell 2D simulation. Therefore the discharge firing voltage characteristic showed a low characteristic than a rectangular type and round type in case of electrode which used tip of a triangle type, and displayed a discharge electric current as a same voltage was low.

To improve mean-life and reliability of power cable, we have investigated specific heat (Cp) and thermal conductivity of XLPE insulator and semiconductive materials in 154kV underground power transmission cable. Specimens were respectively made of sheet form with EVA, EEA and EBA added 30wt%, carbon black, and the other was made of sheet form by cutting XLPE insulator in 154kV power cable. Specific heat (Cp) and thermal conductivity were· measured by DSC (Differential Scanning Calorimetry) and Nano Flash Diffusivity. Specific-heat measurement temperature ranges of XLPE insulator were from 20[$^{\circ}C$] to 90[$^{\circ}C$], and the heating rate was 1[$^{\circ}C$/min]. And the measurement temperatures of thermal conductivity were 25[$^{\circ}C$}], 55[$^{\circ}C$] and 90[$^{\circ}C$]. In case of semiconductive materials, the measurement temperature ranges of specific heat were from 20[$^{\circ}C$] to 60[$^{\circ}C$], and the heating rate was 1[$^{\circ}C$/min]. And the measurement temperatures of thermal conductivity were 25[$^{\circ}C$] and 55[$^{\circ}C$]. From these experimental results, both specific heat and thermal conductivity were increased by heating rate because volume of materials was expanded according to rise in temperature.

This paper was investigated the changes of surface properties of high-temperature-vulcanized(HTV) semiconductive silicone rubber due to oxygen plasma discharge. The modifications produced on the silicone surface by oxygen plasma were accessed using x-ray photoelectron spectroscopy(XPS), contact angle and Scanning Electron Microscope(SEM). The results of the chemical analysis showed that C-H bonds were broken due to plasma discharge and Silica-like bonds (SiOx. x=3~4) increased. It is thought that the above changes lead to the increase of surface energy of high-temperature-vulcanized(HTV) semiconductive silicone rubber. The micromorphology of surface and hydrophobicity due to plasma discharge based on our results were discussed.

Poly (methyl methacrylate) (PMMA) is one of the promising representive of polymer gate dielectric for its high resistivity and sutible dielectric constant. PMMA (Mw=96700) films were prepared on p-Si by spin coating method. PMMA were coated compactively and flatly as observeed by AFM. MIS(Al/PMMA/p-Si) structure was made and capacitance-voltage (C-V) and current-voltage (I-V) measurements were done with PMMA films for different thermal treatment temperature. PMMA films were showed proper dielectric constant and breakdown voltage. Above the glass transition temperature PMMA films degraded. C-V measured at various frequencies, dielectric constant increased a little. The absence of hysteresis in the C-V characteristics, which eliminate the possibility of mobile charges in the PMMA films. The observed thermal stability, smooth surfaces, dielectric constant, I-V behavior implies PMMA formed by spin coating can be used as an efficient gate dielectric layer in OTFTs.

Colloidal Silica(CS)/silane sol solutions were prepared in variation with synthesizing parameters such as ratio of CS to silane and reaction time. In the case of LHSA CS/tetramethoxysilane(TMOS)/methyltrimethoxysilane(MTMS) CS/silane sol, coating film had stable contact angle with increasing reaction time excepting for 48hours. Also, the LHSA CS/TMOS/MTMS coating film had more enhanced flat surface with increasing the amount of MTMS and increasing reaction time. In the case of thermal stability, thermal dissociation of LHSA CS/MTMS sol did not occur up to $550^{\circ}C$.

Light reflectance and arc resistance of PTFE composites were investigated. PTFE composites have been used widely as a material for circuit breaker nozzle. Arc energy is transported to the nozzle material by radiation. It is needed to add some fillers to PTFE to avoid energy penetration into the nozzle material. In this paper, some fillers that have endurance in the high temperature arc environment were added into PTFE. The light reflectance and arc resistance of PTFE composites according to the kinds and content of fillers were investigated.

In this paper, parameters of electron temperature and density for the mercury-free lighting-source were measured to diagnosis and analyze in Xe based inductively coupled plasma(ICP). In results at several dependences of 20~100 mTorr Xenon pressure, 50~200W RF power and horizontal distribution were especially mentioned. When Xe pressure was 20mTorr and RF power was 200W, the electron temperature and density were respectively 3.58eV and $3.56{\times}10^{12}cm^{-3}$. The key parameters of Xe based ICP depended on Xe pressure more than RF power that could be verified. A high electron temperature and low electron density with a suitable Xe pressure are indispensible parameters for Xe based ICP lighting-source.

This paper presents the electrical characteristics of metal oxide varistors for lightning surge arresters. ZnO varistors were fabricated with typical ceramic production methods and two types of varistors were also prepared to be compared. The nominal discharge current and line discharge class of those varistors are $10kA(8/20{\mu}s)$ and class 3, respectively. The diameter of varistors manufactured and prepared were in the range of 61.6~65.0mm and the thickness of those were in the range of 27~42.52mm. The reference and residual voltage were tested and reference and residual voltage per 1mm and the ratio of reference and residual voltage were calculated. The reference voltage per 1mm of varistors manufactured was about 175V/mm but that of A's and B's varistors was nearly 200V/mm. The residual voltage exhibited the same trends as the reference voltage, so the reference and residual voltage per 1mm of domestic varistors should be increased. According to the results of tests, it is thought that if the reference and residual voltage per 1mm were increased to 200V/mm and 330V/mm, domestic ZnO varistors would be possible to apply to the station class arresters in the near future.

우리나라 송전선로의 위치는 국토의 65%에 이른 산지에 대부분 포설되어 있기 때문에 산볼과 같은 화재가 발생시 폴리머 애자에 대한 신뢰성에 중요한 문제점을 발생시킬 수 있다. 따라서 산불의 가장자리 온도인 $600^{\circ}C$ 부근에 노출된 폴리머 애자의 재질에 대한 특성 분석을 실시하였다. 그 결과 애자의 표면은 무기물이 노출되어 다공성의 특성을 보였고, 내아크시험 결과는 하부 갓의 아크소멸 시간은 A시료는 260초, 290초였고, B시료는 335초, 336초였다. 그리고 접촉각 측정결과는 첫 번째 갓의 하부부분이 상부에 비하여 $3^{\circ}$정도 높게 나타났다.

Fabrication of c-axis oriented $(Hg_{0.75}Rc_{0.25})Ba_2Ca_2Cu_3O_y$ thick fabricated has been attempted using Ni substrates with the buffer layer of Cr or NiO. Coexistence of $(Hg_{0.75}Rc_{0.25})Ba_2Ca_3Cu_4O_y$ pellets wad found to stabilize $(Hg_{0.75}Rc_{0.25})Ba_2Ca_2Cu_3O_y$ phase of the tape. The c-axis oriented tapes were reproducibly obtained on the NiO/Ni substerate and they recorded high $B_{irr}$ at 77K.$(Hg_{0.75}Rc_{0.25})Ba_2Ca_2Cu_3O_y$ 1223.

Ploycrystalline $Pb(Zr_{0.5},Ti_{0.5})O_3$ and $BaTiO_3$ powder were prepared by sol-gel process. The alumina substrate were sintered at $1400^{\circ}C$ with bottom electrode of Pt for 2 hours. The Pb(Zr0.5,Ti0.5)O3 / BaTiO3 multilayered thick films with laminating times were fabricated on alumina substrate by screening printing method. The obtained thick films were sintered at $800^{\circ}C$ with upper electrode of Ag paste for 1 hour. Structural properties of Pb(Zr0.5,Ti0.5)O3 / BaTiO3 multilayered thick films were investigated. As a result of the Differential Thermal Analysis(DTA) of Pb(Zr0.5,Ti0.5)O3, exothermic peak was observed at around $650^{\circ}C$. The X-ray diffraction (XRD) patterns indicated that BaTi03 and Pb(Zr0.5,Ti0.5)O3 phases and porosities were formed in the interface of Pb(Zr0.5,Ti0.5)O3 / BaTiO3 multilayered thick films.

Discharge of the flat lamp lighting source research are requested very much. For improving brightness, life time, efficiency of flat lamp, plasma diagnosis of the flat lamp lighting source to understand property of lighting source is very important, distance of discharge electrode is 5.5mm and width is 16.5mm, we measured electron temperature and electron density measured with single langmuir probe in flat lamp, we tested the discharge from 100 Torr to 300 Torr pressure, the Pulse is rectangular pulse with frequency 20kHz and Duty ratio 20%. Resultly, electron temperature decreases and electron density increase as increase the gas pressure and electron temperature decreases and electron density increase as increase the voltage.

알루미나 함유량의 변화에 따른 국산 2001년, 2004년 애자와 외국산 2000년도 36,000lbs 불소켓형 현수애자에 대해 물성 분석을 실시하였다. 그 결과 2001년도 자기애자의 알루미나 함유량을 17%로 하고 2004년도 알루미나 함유량이 20%로 하였을 경우 자기 애자의 기계적 특성은 10% 정도 향상되었다. 그리고 2001년도에 제조한 애자의 자기 상대밀도는 이론밀도의 96%에 도달하였으나 2004년도에 제조한 애자의 상대 밀도는 이론민도의 98%에 도달하였으면 애자의 균일성을 나타내는 Qs 값은 5.01로 높게 나타났다.

ACSR전력선의 송전용량 증가를 위해 개발된 중용량저이도 송전선인 STACIR/AW(Super Thermal-resistant Aluminum alloy Conductors, aluminum-clad Invar-Reinforced)전선은 초내열 Al도체 및 인바강선의 사용으로 비교적 고온에서의 안정적 운전이 가능하다. 그러나 고온 환경에서 장시간 노출된 STAClR/AW전선의 안정적 관리를 위해서는, 열화 된 STACIR/AW 전선의 인장강도, 각 구성소재의 탄성계수, 비틀림 계수 등과 같은 기계적 물성이 장기 운전 모의를 위해 선정된 열화온도, 열화시간 등에 대해 종합적으로 평가될 필요가 있다. 또한 크립 등과 같이 고온응력 부하상태에서의 변형거동과 탄성계수 및 선팽창계수의 온도의존성 등은 전선의 이도관리와 예측을 위해서도 명확히 규명되어야할 중요한 관리 인자이다. 그러나 현재까지는 이들에 대해 수행한 어떠한 연구결과들도 보고 되어 있지 않은 실정이다. 본 연구에서는 STACIR/AW $410mm^2$ 송전선을 장시간 운전의 모의를 위해 가속열화 시키고 가속열화에 따른 STACIR/AW 전선 및 그 구성소재의 강도, 비틀림 특성의 변화를 조사하여 장시간 운전에 따른 STACIR/AW전선의 안정성을 평가하여 보고하고자 하였다.

최고속도 350km/h의 한국형 고속철도시스템은 안전보장과 사고예방을 위해서는 시스템 위험분석에 근거한 안전검증과 성능확인이 요구된다. 본 논문에서는 고속철도 차량시스템 개발을 위한 시스템 개발요건과 위험도 분석에 근거한 안전성능요건을 근거로 하여, 차량시스템에 대한 일반 안전요건, 구조적 안전요건 및 핵심 장치별 안전요건으로 구성된 한국형 고속철도 차량시스템의 안전설계 요건분석 결과를 소개한다.

고속철도는 한번에 1천명에 달하는 승객을 태우고 시속 300km를 넘는 고속으로 주행하는 만큼 성능과 안전에 대한 철저한 사전 검증이 필수적이며, 특히 새로운 차량시스템의 개발은 철저한 성능검증 및 안전성을 확보하는 시험평가 과정을 반드시 거쳐야 한다. 본 논문에서는 최고속도 350km/h인 한국형 고속철도 차량시스템 개발사양의 성능요구 조건을 입증하기 위한 시험으로서, 핵심 개발품 단위별 구성품 시험, 개발품 단위간의 조합시험, 차량에서의 기능 동작 확인을 위한 완성차시험(단차시험 및 편성시험)및 전기신호 및 선로구축물 시스템과의 적합성 및 연계성을 확인하는 시운전 시험으로 구분하여 한국형 고속철도 차량시스템의 성능시험 체계 및 성능시험 기준(안)의 개발 내용을 소개하고자 한다.

In this study, it analysis electric field of SMD(Surface Mounted Device) Inductor Core and it get electric field only exist inside of SMD core. Therefore electric fields do not affect any device and equipments. These results are very important to design data acquisition system(several test equipments such as temperature, impedance, and current test), because data acquisition system can place under the SND Inductor core. So, it can be decrease their test error due to electric field.

인버터 구동 회전기기의 운전수명을 보장하기 위해서는 기존의 시험 방법에 포함되지 않은 PWM 가변속 구동에 따른 고조파 손실과 과도전압 충격의 문제점을 고려한 새로운 장기 신뢰성 평가 기법이 절실히 필요한 상황이기 때문에 본 연구에서 시험모델을 설정하고자 한다. 결과로는 종래는 비파괴시험에 의한 off-line 진단법이 주로 시행되었지만, 최근에는 상태량을 계측하는 신종 센서의 개발이 진행되어 모니터링법에 의한 on-line 진단법이 점차로 증가하고 있다.

Bismuth high Tc superconducting thin films are fabricated via a co-deposition process by an ion beam sputtering with an ultra low growth rate, and sticking processing of the respective elements are evaluated. The sticking processing of bismuth element in bismuth high Tc superconducting thin film formation was observed to show a unique temperature dependence; it was almost a constant value of 0.49 below about $730^{\circ}C$ and decreased linearly over about $730^{\circ}C$. This temperature dependence can be elucidated from the evaporation and sublimation rates of bismuth oxide, $Bi_2O_3$, from the film surface. It is considered that the liquid phase of the bismuth oxide plays an important role in the bismuth phase formation in the co-deposition process.

BSCCO thin films fabricated by using the evaporation method. As a result, although the composition of Bi2212 was set up, the phase of Bi2201, Bi2212 and Bi2223 was formed. The formation area of these stable phases is indicated as inclined line in the direction of the right lower end from the Arrhenius plot of the substrate temperature-oxidation gas pressure, and are distributed in very small area. The activation energy for the phase transformation from the Bi2201 to the Bi2212 is estimated in terms of the Avrami equation.

가스센서는 응용 분야와 기능 및 종류가 다양하고 최첨단 분야로서 학문적으로는 물리, 화학, 전기, 전자 및 기계 등의 배경을 필요로 하며 산업적으로는 공업 전 분야와 농림, 축산, 사무기기에서 뿐만 아니라 공해 방진용(자동차 연소제어 및 배출가스 제어, 대기오염 감시등), 민생용(조리, 환기, 공조 등), 교통 보안용(음주운전측정 및 음주운전 방지장치 등), 방재용(가스 누설 탐지기, 불완전 연소 방지, 산소 결핍, 화재 등), 의료용(호기, 마취가스의 분석 등) 매우 광범위하며 점점 더 확대되어 가고 있다. 본 연구에서는 검출 가스 종류에 따라 졸-겔법으로 감응막을 최적 설계하고, 최적으로 설계된 감응막을 디핑법으로 코팅처리한 후 최적으로 열처리하여 센서를 제작하였다. 또한, 자체 제작한 가스검출 시스템에 제작된 센서를 장착하여 센서의 가스 검출 특성을 측정하고, 측정 데이터를 이용하여 휴대용 가스 검출 시스템을 설계 제작하였다.

The $(Sr_{1-x}Ca_x)TiO_3$(SCT) thin films are deposited on Pt-coated electrode (Pt/TiN/$SiO_2$/Si) using RF sputtering method with substitutional contents of Ca. The optimum conditions of RF power and Ar/$O_2$ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin film was about 18.75[$\AA$/min]. The dielectric constant was increased with increasing the substitutional contents of Ca, while it was decreased if the substitutional contents of Ca exceeded over 15[mol%]. The capacitance characteristics had a stable value within ${\pm}4$[%] in temperature ranges of -80~+90[$^{\circ}C$].

Ozone is useful oxidizing gas for the fabrication of BSCCO thin films. In order to obtain high quality oxide BSCCO thin films, higher ozone concentration is necessary. The growth rates of the films was set in the region from 0.17 to 0.27 nm/min. MgO(100) was used as a substrate. In this paper oxidation property was evaluated relation between oxide gas pressure and inverse temperature(CuO reaction). The obtained condition was formulated by the fabrication of Cu metal thin film by co-deposition using the Ion Beam Sputtering method. Because the CuO phase peak appeared at the XRD evaluation of the CuO thin film using ozone gas, this study has succeeded in the fabrication of the CuO phase at $825^{\circ}C$.

In this study, the DC dielectric breakdown of epoxy composites used for molding material was experimented and then its data were simulated by Weibull distribution equation. From the analysis of Weibull distribution, it was confirmed that as the allowed breakdown probability was given by 0.1[%], the applied field value needed to be under 21.5[kV/mm].

In this study, the design simulation for optimal wire batch around service line was made to improve the dielectric strength at the primary winding using Finite Element Method. The automatic convergence algorithm for finding of limit object value using loop circulation method was developed to make the optimal design simulator. The modulation method was suggested to make division time faster which was very important for full simulation efficiency. As a result, the simulation time was reduced and the optimal wire batch design was obtained.

In this study, the Thermally Stimulated Current(TSC) of corona charged PTFE is studied and the simulation of corona charging process is also calculated by Finite Element Method. The electrets which were formed by applying high voltages (DC ${\pm}5{\sim}{\pm}8$ [kV]) to PTFE, are used to measure TSC in the temperature range of $-100{\sim}+200$ [$^{\circ}C$] and then the Finite Element Method is performed to examine corona charging process using a obtained physical constants. As a result. it is confirmed that the charging negative corona is profitable as the applications are manufactured, because the time constant of negative corona is much larger than it of positive corona. And it is attempted to estimate the corona charging process in space using simulation.

We investigated the fault current limiting characteristics according to the various facilities in power system. Power systems are becoming larger and larger for meeting electric power demand. Therefore, the over-currents resulting from contingencies such as short circuits are increasing higher, which causes the ratings of circuit breakers(CBs) to increase. Upgrading or replacement of CBs is not difficult from the technical and economical point of view. Bus split is being adopted into a part of 154 kV power systems, but it has adverse effects such as overload to neighboring power systems, increased voltage fluctuation, and decreased power system stability. For 345 kV power systems, the bus split measure is not feasible and dc reactors are being suggested. The superconducting fault current limiter is a protection gear of new concept that limits fault current automatically in a few milliseconds. It can also provide the effect of CB capacity increase, relaxation of power machine criteria, enhancement in power system reliability, and flexible power system operation.

The objectives of this study are to improve the aerodynamics performance on the down-wind blade system with folding type blade which consists of the folding type rotor blade, wind vane yawing stabilizer and a bevel gearbox. The aerodynamics performance for the new wind turbine system are compared with those of the conventional up-wind blade system. In addition to, a novel multi voltage inverter system is applied for reductions of harmonic.

Thin films of $BaTiO_3$ system were prepared by radio frequency(rf)/dc magnetron sputtering method. We have investigated crystal structure, surface morphology and PTCR(positive-temperature coefficient of resistance) characteristics of the specimen depending on second heat-treatment temperatures. Second heat treatments of the specimen were performed in the temperature range of 400 to $1350^{\circ}C$. X-ray diffraction patterns of $BaTiO_3$ thin films show that the specimen heat treated below $600^{\circ}C$ is an amorphous phase and the one heat treated above $1100^{\circ}C$ forms a poly-crystallization. In the specimen heat-treated at $1300^{\circ}C$, a lattice constant ratio (c/a) was 1.188. Scanning electron microscope(SEM) image of $BaTiO_3$ thin films of the specimen heat treated in between 900 and $1100^{\circ}C}$ shows a grain growth. At $1100^{\circ}C$, the specimen stops grain-growing and becomes a poly-crystallization.

Recently, polymer insulator and bushing that are used for high voltage application have some advantages such as light weight, small size, vandalism resistance, hydrophobicity and easy making process. The pole mount transformer installed in distribution system is acting direct role in supply of electric power and the electric power device should drive safely for long tenn. In this paper, the polymer bushing of pole transformer is designed adaptively to current assembly method, designed bushing is manufactured on basis of that result. The electric field of designed transformer is investigated by FEM program.

본 논문에서는 LabVIEW program을 사용하여 크기가 다른 파이렉스 글라스 방전관의 오존 농도를 연속적으로 측정하여 특성을 분석하였다. 또한 Flux-2D program을 사용하여 파이렉스 방전관의 전계를 분석하였다. 실험 결과에 따르면 1[$\ell$/min]에서 가장 오존 농도가 높았으며, 파이렉스 글라스 방전관 I 에서는 약 62[g/$m^3$]. 파이렉스 글라스 방전관II 에서는 약 48[g/$m^3$]으로 나타났다. 또한 고압 펄스 전원에 따른 오존농도 변화를 3D분석을 통해 확인 할 수 있었다. 확인된 분석을 통해 오존농도를 요구하는 만큼 생성한다면, 에너지 손실을 감소시키고 전극 수병을 최대화 할 수 있다.

최근, 국내에서는 스마트홈 기술이 공동주택인 아파트를 중심으로 점차 도입되고 있는 실정이다. 스마트홈의 주거공간은 홈네트워크를 기반으로 하는 다양한 정보(가전)기기들이 활용되고 있다. 이러한 주거생활환경에 의해 전기에너지의 의존도가 지속적으로 증가하고 있어, 먼저 스마트 홈 환경하 수용가 변압기 2차측에서의 전기합선과 누전에 대한 전기안전 및 진단의 기반기술을 제시한다. 다음으로, 주거시스템이 지능형홈으로 발전함으로서, 소비 전기량이 급속히 증가하는 추세이다. 따라서 본 논문에서는 홈거주자의 정보가 전기기 사용유무에 따라서 전원상태를 지능적으로 차단/통전시켜 소비전력을 최소화할 수 있는 Auto 스위치에 대해 기술하고자 한다.

A.T.S.의 스위칭 구조와 접점 환경은 주로 아크 전류, 접촉 저항, 아크 시간 등의 불리적 요인이 주로 마모와 특성에 영향을 미치게 된다. 사용되는 접점 재료는 W 또는 WC-Cu 계로 형상과 크기는 전형적인 반구형 구조의 접촉으로 구동이 이루어진다. 따라서 A.T.S.용 접점의 아크 마모 특성 시험을 위한 고려 요인은 이러한 점을 고려하여 시험과 분석이 이루어 졌다. 접점의 마모 특성 실험식으로부터 실제적인 관점에서 보면 제한된 수명을 나타내는 $n_L$을 보장하기 때문에 b<1의 경우가 가장 바람직한 결과로 ATS 접점 시편의 경우 $b{\fallingdotseq}0.99$로 안정된 접점 아크 마모 특성을 갖는 것으로 판단된다. 아크 전압에 대한 모델링과 실험에서 접점 간극 거리 1<0.1mm, 아크전류 i<100A의 시험 조건에 대해 검토한 결과 ATS 접점 시편의 아크전압은 $u_a=10.2V$로 계산되었다. 이 값은 설험적인 값과 상당히 접근하는 특성을 갖는 것으로 나타났으며, 아크에 의한 마모를 억제하기 위해 첨가하는 WC 또는 W의 복합 소결로 인해 아크 에너지가 감소되는 것을 보여준다. 한편 접점의 아크 동작이 분리되는 순간의 동작 시험에서 기존 W(50%wt)-Cu(50%wt) 접점의 값과 비교하면 분리시 아크 전압은 상대적으로 낮아지는 현상은 W강화 첨가량의 증가로 인한 아크 에너지 감소의 제한성을 나타내는 것으로 사료된다.

The purpose of this study is to design the digital surge counter for lightning arresters. The used detecting method for surges is using the signal of both ends of ZnO varistor. The electronic detecting parts of the digital counter are arranged in outside of main processer for protecting it from noise. The detecting parts change detected signals into small signals. The countermeasures for noises are (1) Shielding (2) Reinforcement of power circuits (3) Cables & Circ1e core (4) Watch-doc & control of input signals.

The main objective of this paper is to module design and pressure relief test a new type of polymer gapless surge arrester for power distribution line. Metal oxide surge arrester for most electric power system applications, power distribution line and electric train are now being used extensively to protect overvoltage due to lightning. Surge arresters with porcelain housing must not have explosive breakage of the housing to minimize damage to other equipment when subjected to internal high short circuit current. When breakdown of gapless elements in a surge arrester occurs due to flashover, fault short current flows through the arrester and internal pressure of the arrester rises. The pressure rise can usually be limited by fitting a pressure relief diaphragm and transferring the arc from the inside to the outside of the housing. However, there is possibility of porcelain fragmentation caused by the thermal shock, pressure rise, etc. Non-fragmenting of the housing is the most desired way to prevent damage to other equipment. The pressure change which is occurred by flashover become discharge energy. This discharge energy raises to damage arrester housing and arrester housing is dispersed as small fragment. Therefore, the pressure relief design is requested to obstruct housing dispersion.