• The Korean Journal of Ceramics
• /
• v.5 no.1
• /
• pp.19-24
• /
• 1999

The influences of TiB2 additions to the β-sialon on mechanical propeties and electrical discharge machinability were investigated. Samples were prepared by adding 15, 30 and 45 vol.% TiB2 particles as a second phase to a β-sialon matrix. The β-sialon-TiB2 composites were sintered by hot pressing in a nitrogen atmosphere at 1800℃ with pressure of 30 MPa. The fracture toughness of the composites was increased with TiB2 content except 45 vol.% TiB2 composite. The crack propagation and crack deflection were observed with a SEM for etched samples after vicker's indentation. The composites containing more than 30 vol.% TiB3 had resistivity lower than 10-3 Ω㎝. The electrical discharge machining (EDM) of composited was conducted with two kind of machines such as die-sinker and wire cutter. The machinability was evaluated with the cutting rate surface roughness after machining.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.6-12
• /
• 2014

In the present work, $WO_3$ and $WO_3-TiO_2$ were prepared by the chemical deposition method. Structural variations, surface state and elemental compositions were investigated for preparation of $WO_3-TiO_2$ sonocatalyst. X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and transmission electron microscopy (TEM) were employed for characterization of these new photocatalysts. A rhodamine B (Rh.B) solution under ultrasonic irradiation was used to determine the catalytic activity. Excellent catalytic degradation of an Rh.B solution was observed using the $WO_3-TiO_2$ composites under ultrasonic irradiation. Sonocatalytic degradation is a novel technology of treating wastewater. During the ultrasonic treatment of aqueous solutions sonoluminescence, cavitaties and "hot spot" occurred, leading to the dissociation of water molecules. In case of a $WO_3$ coupled system, a semiconductor coupled with two components has a beneficial role in improving charge separation and enhancing $TiO_2$ response to ultrasonic radiations. In case of the addition of $WO_3$ as new matter, the excited electrons from the $WO_3$ particles are quickly transferred to $TiO_2$ particle, as the conduction band of $WO_3$ is 0.74 eV which is -0.5 eV more than that of $TiO_2$. This transfer of charge should enhance the oxidation of the adsorbed organic substrate. The result shows that the photocatalytic performance of $TiO_2$ nanoparticles was improved by loading $WO_3$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.24-31
• /
• 2022

This study investigated microstructures, crystal structures, polarization, dielectric and electromechanical properties of 0.76Bi_1/2Na_1/2TiO₃-0.24SrTiO₃ (BNT-24ST)-based piezoceramcs by adding Li₂CO₃ and B₂O₃ (LB) as sintering aids for low-temperature sintering. All samples were successfully synthesized using conventional solid-state reaction method and sintered at 950, 1,000, 1,050, 1,100 and 1,175℃ for 2 hours. Without LB, specimens required sintering temperatures over 1,175℃ for sufficient densification, while the addition of 0.10-mol LB decreased the sintering temperatures down to 950℃. The average grain size and dielectric properties of BNT-24ST-10LB ceramics were enhanced with increasing sintering temperature. We found that the low-temperature sintered BNT-24ST piezoceramics by adding LB showed the d₃₃*value of 402 pm/V at 4 kV/mm after sintering at 1,050℃, which was better than that of high-temperature fired specimens sintered at 1,175℃ without LB (242 pm/V). We believe that the results of this study promise a candidate for low-cost multilayer ceramic actuator applications.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.1
• /
• pp.24-27
• /
• 2011

Effect of substitution of Mn for Ni on transformation behavior, shape memory characteristics and superelasticity of Ti45Ni-5Cu alloy has been investigated by means of electrical resistivity measurements, X-ray diffraction, thermal cycling tests under constant load and tensile tests. The one-stage B2-B19' transformation occurred when Mn content was 0.5 at%, above which the two-stage B2-B19-B19' transformation occurred. A temperature range where the B19 martensite exists was expanded with increasing Mn content because decreasing rate of Ms (60 K / % Mn) was larger than that of Ms' (40 K / % Mn). Ti-(45-x)Ni-5Cu-xMn alloys were deformed in plastic manner with a fracture strain of 60 % ~ 32 % depending on Mn content. Clear superelasticity was found in fully annealed Ti-(45-x)Ni-5Cu-xMn alloys with Mn content more than 1.0 at%, which was ascribe to a solid solution hardening by substitution of Mn for Ni.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.32-37
• /
• 2002

Passive polarization mode splitters at λ= 1.55 ${\mu}{\textrm}{m}$ were designed and fabricated based on Ti:x-cut LiNbO$_3$ single-mode optical waveguide and two-mode interference theory. The splitting ratio with waveguide width 8 ${\mu}{\textrm}{m}$, branching angle 0.55$^{\circ}$ and interfering length 470 ${\mu}{\textrm}{m}$ showed 16.18 dB, 21.25 dB for TE and TM input polarization modes, respectively. Polarization cross-talk of -16.28 dB and -21.28 dB for TE and TM modes was achieved. Total insertion losses of 2.24 dB/cm (TE) and 2.41 dB/cm (TM) were also measured. The devices operated nearly wavelength independently over a range or 30 nm.

• Journal of the Korean Ceramic Society
• /
• v.35 no.3
• /
• pp.287-293
• /
• 1998

The effects of B2O3 addition on the sintering behavior and th microwave dielectric properties of $(Mg_{0.93}Ca_{0.07})TiO_3$ ceramics were investigated. By addition of $B_2O_3$, increases the density of the ceramics increases and grain growth enhances, It was densified to over 94% of $(Mg_{0.93}Ca_{0.07})TiO_3$ theoretical density by the addition of 0.15-1.0wt% B2O3 and stable microwave dielectric properties observed by the addition of 0.2-0.4wt% $B_2O_3.\;(Mg_{0.93}Ca_{0.07})TiO_3$ ceramics sintered at $1200^{\circ}C$ exhibits maximum dielectric constants of 24-25 quality factor($Q{\times}f$) of more than 70000 and temperature coefficient of resonant frequency of $0\;ppm/^{\circ}C$ by adding of 0.15-0.4wt% $B_2O_3$.

• Journal of environmental and Sanitary engineering
• /
• v.24 no.4
• /
• pp.112-115
• /
• 2009

This research was performed to purify water quality through removing T-N, and T-P and to estimating rate of $NO_x$ by the response of photocatalyst using ceramics. The ceramics was a mixtures of Titanium Diboride($TiB_2$) which is used to develop armored cars with excellent protective power and lightness, Olivine, and Hwangto with water and was furnaced for an hour at $1160^{\circ}C$. Hwangto and Olivine used in the study are produced at Haenam-gun, Jeonnam, and Andong-city, Gyeongsangbuk-do, respectively. The ground Hwangto and Olivine were seived through PR $100{\times}200$, and $TiB_2$ was a product of SIGMA ALDRICH. The experiment was performed under the sunlight, Mass flow controller was used for constant flow to pass through the pyrex reactor which was fully charged with furnaced ceramics. The concentration of $NO_2$ gas passed through the pyrex reactor was measured by Multi Gas Monitor. The reaction took for 60 minutes, The material was exposed to sunlight for 40 minutes. The sunlight was interrupted before and after the exposure for 10 minutes. The result showed that the concentration of $NO_2$ gas of the ceramics with $TiB_2$ and without $TiB_2$ became reduced and then maintained the same concentration under the sunlight, and became increased when the sunlight is interrupted. The $NO_2$ removing efficiency of the ceramics mixed with $TiB_2$ was 14~43% higher than that of the ceramics without $TiB_2$ under the sunlight. The study showed that the removing rate of $NO_2$ was 80% when the mixture rate of Hwangto, Olivine, and $TiB_2$ was 68%, 30% and 2%.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.1
• /
• pp.51-56
• /
• 1999

$TiO_2$ thin films were spin coated on commercial Nickel-Silver with 2%Ti-naphthanate toluene solution by sol-gel process. The thin films were heat-treated at $500^{\circ}C$ for 2min and then decorative-protective coating was obtained. The conditions for gold colored coating, and the morphology, microstructure and color of the coating surface were have been characterized by Optical microscope, Photospectrometer and XRD. The heating temperature of colored-$TiO_2$ coating was $500^{\circ}C$ and was preferable. The average thickness of 1 time coating was $0.24{\mu}m$ and the total thickness increased linearly as a function of the coating time. The color of amorphous colored-$TiO_2$ coating was changed from gold to dark redish gold with coating time. 'L' as lightness and 'b' were decreased to red, but 'a' was decreased to blue after increase with coating time.

• Journal of the Korean Ceramic Society
• /
• v.38 no.6
• /
• pp.558-567
• /
• 2001

본 연구에서는 알콕사이드를 전구물질로 하는 졸겔공정을 이용하여 Bi 과잉 12 mol%의 조성인 B $i_4$ $Ti_3$ $O_{12}$ 박막과 B $i_4$ $Ti_{3-x}$T $a_{x}$ $O_{12}$(x=0.1, 0.2, 0.3) 박막을 제조하였다. XPS 분석에 따르면 Ta 치환 x=0.2에서 Bi 4f의 photoemission 곡선이 낮은 결합에너지로 이동하였고 피크 강도가 감소하는 현상이 관측되었다. 이는 x=0.1과 0.2 사이에서 Bi-O 결합이 길어져 인장상태 하에 있었음을 나타내었다. B $i_4$ $Ti_3$ $O_{12}$(BIT) 박막의 유전상수와 유전손실은 100 kHz에서 340, 0.05이었고, B $i_4$ $Ti_{3-x}$T $a_{x}$ $O_{12}$ 박막에서 이들 값은 x=0.1에서 가장 높았으며, 각각 480, 0.13이었다. B $i_4$ $Ti_3$ $O_{12}$ 박막의 잔류분극과 항전계는 1.24$\mu$C/$ extrm{cm}^2$, 31.4 kV/cm 이었으나, Ta 치환 x=0.2에서 이들 값은 각각 19.7$\mu$C/$\textrm{cm}^2$, 49.5 kV/cm 에 이르렀다. 또한, B $i_4$ $Ti_3$ $O_{12}$ 박막의 누설전류 밀도는 ~$10^{-6}$ A/$\textrm{cm}^2$ 정도이었으며, Ta 치환은 누설전류를 감소시켜 Ta 치환 x=0.2 이상에서 BIT 박막에 비해 한 차수 정도 낮아졌다. Ta 치환에 따른 B $i_4$ $Ti_3$ $O_{12}$ 전기 물성에서 변화는 Bi-O 결합에서 관측된 인장상태로의 전이와 연관성이 있었으며, 덧붙여 치환에서 생성된 전자에 의한 정공보상이 이에 영향을 끼쳤다. 정공보상이 이에 영향을 끼쳤다.끼쳤다.

• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.710-714
• /
• 2014

The effect of titanium dioxide ($TiO_2$) on the properties of color conversion glasses was examined for glasses based on $BaO-ZnO-B_2O_3-SiO_2$. One glass sample, containing 25 mol% of each component, was used as a reference; the other three glass samples contained 1, 3, and 5 mol% $TiO_2$, respectively. The four color conversion glass samples were prepared by sintering a mixture of glass frits and a $YAG:Ce^+$ phosphor. The characteristics of the color conversion glass samples, such as luminous efficacy, luminance, CIE (Commission International de I'Eclairage) chromaticity, CCT (Correlated Color Temperature), and CRI (Color Rendering Index) were analyzed according to the PL spectrum. The refractive index of the glass samples was found to increase with the titanium dioxide content. In conclusion, luminous efficacy of color conversion glasses increased as the content of $TiO_2$ was raised in the glass matrix.