• International Journal of Aeronautical and Space Sciences
• /
• v.9 no.2
• /
• pp.18-33
• /
• 2008

This paper presents design optimization of a new Active Twist Rotor (ATR) blade and conducts its aeroelastic analysis in forward flight condition. In order to improve a twist actuation performance, the present ATR blade utilizes a single crystal piezoelectric fiber composite actuator and the blade cross-sectional layout is designed through an optimization procedure. The single crystal piezoelectric fiber composite actuator has excellent piezoelectric strain performance when compared with the previous piezoelectric fiber composites such as Active Fiber Composites (AFC) and Macro Fiber Composites (MFC). Further design optimization gives a cross-sectional layout that maximizes the static twist actuation while satisfying various blade design requirements. After the design optimization is completed successfully, an aeroelastic analysis of the present ATR blade in forward flight is conducted to confirm the efficiency in reducing the vibratory loads at both fixed- and rotating-systems. Numerical simulation shows that the present ATR blade utilizing single crystal piezoelectric fiber composites may reduce the vibratory loads significantly even with much lower input-voltage when compared with that used in the previous ATR blade. However, for an application of the present single crystal piezoelectric actuator to a full scaled rotor blade, several issues exist. Difficulty of manufacturing in a large size and severe brittleness in its material characteristics will need to be examined.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.35-38
• /
• 2003

In this paper, we investigated the electric and acoustic properties of piezoelectric composites, which were fabricated using polymer and piezoelectric ceramics, when the volume fraction of PZT varies. Practically, the shrinkage rate of polymer is an important factor in ultrasonic transducer fabrication. When 10 wt% filler A was added into polymer(Epofix), the lowest shrinkage was resulted. The electromechanical coupling factor($k_t$) of the fabricated piezoelectric composites showed its highest when the volume fraction PZT was 0.6. It decreased if the volume fraction was higher than the value. The relative permittivity and acoustic impedance of piezoelectric composites decreased linearly when PZT volume fraction was decreased. The lowest acoustic impedance was 3.2 when the volume fraction of PZT was 0.2.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.45-50
• /
• 2020

Magnetoelectric (ME) composites were designed using the PMN-PZT single crystal and Ni foils; the properties and magnetic-field sensitivities of ME composites with different piezoelectric vibration modes (i.e., 31, 32, and 36 modes that depend on the crystal orientation of the single crystal) were compared. In the off-resonance condition, the ME coupling properties of the ME composites with the 32 and 36 piezoelectric vibration modes were better than those of the ME composites with the 31 piezoelectric vibration mode. However, in the resonance condition, the ME coupling properties of the ME composites were almost similar, irrespective of the piezoelectric vibration mode. Additionally, in the off-resonance condition (at 1 kHz), the magnetic-field sensitivity of the ME composites with the 36 piezoelectric vibration mode was up to 2 nT and those of the ME composites with the 31 and 32 piezoelectric vibration modes were up to 5 nT. These magnetic-field sensitivities are similar to those offered by conventional high-sensitivity magnetic-field sensors; the potential of the proposed sensor to replace costly and bulky high-sensitivity magnetic field sensors is significant.

• Smart Structures and Systems
• /
• v.14 no.5
• /
• pp.961-980
• /
• 2014

Based on the general theory of elasticity, the static behavior of 2-2 cement-based piezoelectric curved composites is investigated. The actuator consists of 2 cement layers and 1 piezoelectric layer. Considering the electrode layer between the cement layer and the piezoelectric layer as the elastic layer, the exact solutions of the mechanical and electrical fields of the curved composites are obtained by utilizing the Airy stress function method. Furthermore, the theoretical results are compared with the FEM results and good agreements (with almost no error) are obtained, thus proving the validity of this study. Furthermore, the influence of certain parameters is discussed, which can help to get the desired displacements and stresses. Finally, it is seen that the analytical model established in this paper works well, which could benefit the design of this kind of cement-based smart devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.6
• /
• pp.420-425
• /
• 2012

Lead-free piezoelectric ceramic/epoxy composites with '0-3' connectivity were prepared by cold-pressing with a temperature controlled curing method. A ceramic powder with a composition of $(Na_{0.51}K_{0.47}Li_{0.02})(Nb_{0.8}Ta_{0.2})O_3$ was synthesized by a conventional solid state reaction route. The dielectric and piezoelectric properties of ceramic/epoxy composites were characterized as a function of the volume fraction (${\phi}$) of piezoelectric ceramics, which was varied from 70 to 95 vol%. The results indicated that the piezoelectric properties of composites were significantly affected by the volume fraction of ceramics. In terms of the piezoelectric properties, specimens showed the best performance at ${\phi}$= 85 vol%, resulting in the piezoelectric constant $d_{33}$ of 39 pC/N and the figure of merit as a piezoelectric energy harvester ($d_{33}{\cdot}g_{33}$) of 1.24 $pm^2/N$.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.611-614
• /
• 2018

Laminate composites composed of $0.95Pb(Zr_{0.52}Ti_{0.48})O_3-0.05Pb(Mn_{1/3}Sb_{2/3})O_3$ piezoelectric ceramic and Fe-Si-B based magnetostrictive amorphous alloy are fabricated, and the effect of control of the areal dimensions and the thickness of the piezoelectric layer on the magnetoelectric(ME) properties of the laminate composites is studied. As the aspect ratio of the piezoelectric layer and the magnetostrictive layer increases, the maximum value of the ME voltage coefficient(${\alpha}_{ME}$) increases and the intensity of the DC magnetic field at which the maximum ${\alpha}_{ME}$ value appears decreases. Moreover, as the thickness of the piezoelectric layer decreases, ${\alpha}_{ME}$ tends to increase. The ME composites exhibit ${\alpha}_{ME}$ values higher than $1Vcm^{-1}Oe^{-1}$ even at the non-resonance frequency of 1 kHz. This study shows that, apart from the inherent characteristics of the piezoelectric composition, small thicknesses and high aspect ratios of the piezoelectric layer are important dimensional determinants for achieving high ME performance of the piezoelectric-magnetostrictive laminate composite.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.869-872
• /
• 2000

The aim of present work was to fabricate the piezoelectric composite materials of low megahertz applications such as non-destructive testing of materials. Among all the various composites, those with PZT rods embedded in Spurrs epoxy with regular periodicity (1-3 connectivity) was fabricated by dice and fill method. The fabricated size of the PZT cell were 0.18X0.18, 0.28X0.28mm$^2$, respectively. And the volume ratio of the PZT cell were 52, 64%, respectively. The resonant frequency and anti-resonant frequency of the composites were 3.5 MHz and 4.3MHz, respectively. The piezoelectric coupling coefficient were about 38 and 37% and the mechanical quality factor were about 12.7 and 22. These value were very different from these of bulk PZT Plate.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1989.06a
• /
• pp.77-80
• /
• 1989

The aim of the study is to develope the processing technique of PZT-Polymer piezoelectric composite materials for ultrasonic transducer application such as biomedical probe and hydrophone. Piezoelectric composite of PZT and polymer with 1-3 connectivity patterns have been fabricated by dicing-filling method and extrusion forming method. In this study processing forming method. In the study processing steps by extrusion forming method in the preperation of PZT/polymer piezoelectric composites are described. The PZT powder used in the study is commercial powder which is prepared by mixing PbO, TiO$_2$ and ZrO$_2$. The binder, water and plasticizer are mixed with the PZT powder to form a slip. It is necessary to adjust the viescosity of slip according on the PZT rod diameters to be extruded. The electromechanical properties of the piezoelectric composites are characterized in terms of the thickness resonance mode. The pulse response characteristics by the ultrasonic transducer analyzer and osciloscope are evaluated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.08a
• /
• pp.146-149
• /
• 2002

In this study, 2-2 type piezocomposites were made and characteristics as volume fraction of PZT were investigated. The accoustic impedance of 2-2 piezoelectric composites was linearly decreased with decreasing PZT volume fraction. when the volume fraction of PZT was 0.2 the acoustic impedance was 3.2 Mrayl. The electromechanical coupling factor was favourable in comparison with the single phase PZT, and that was about uniformed about 0.68 in the 0.2 to 0.6 of PZT volume fraction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.10a
• /
• pp.50-53
• /
• 1988

Lead titanate powders were prepared by mixed-oxide and sol-gel method. O-3 composites were prepared with these powders using Eccogel polymer. According to the volume percent of the PbTiO$_3$ powders, dielectric, piezoelectric properties and poling conditions were investigated. Relative dielectric constants were exponentially increased with volume percent of PbTiO$_3$. Piezoelectric strain coefficients (d$_{33}$ ) were increased with volume percent of PbTiO$_3$. Figure of merit (d$_{h}$.g$_{h}$) for the O-3 composites prepared by the mixed-oxide and sol-gel method were 2728(x10$^{-15}$ $m^2$/N) and 3100(x10$^{-15}$ $m^2$/N) at 70 volume percent of PbTiO$_3$, respectively.ely.