• Journal of Magnetics
• /
• 제22권2호
• /
• pp.257-265
• /
• 2017

This paper presents a 2-D analytical method to calculate the back EMF of the axial flux permanent magnet synchronous generator (AFPMSG) with coreless stator and dual rotor having magnets mounted on both sides of rotor yoke. Furthermore, in order to reduce the no load voltage total harmonics distortion (VTHD), the initial model of the coreless AFPMSG is optimized by using a developed analytical method. Optimization using the 2-D analytical method reduces the optimization time to less than a minute. The back EMF obtained by using the 2-D analytical method is verified by a time stepped 3-D finite element analysis (FEA) for both the initial and optimized model. Finally, the VTHD, output torque and torque ripples of both the initial and optimized models are compared with 3D-FEA. The result shows that the optimized model reduces the VTHD and torque ripples as compared to the initial model. Furthermore, the result also shows that output torque increases as the result of the optimization.

• 생약학회지
• /
• 제38권1호
• /
• pp.19-21
• /
• 2007

Myristica fragrans has been used for the treatment of stomachache in East Asia. It is very important to determine the amount of myristicin in Myristica fragrans, because excess myristicin causes side effects. In this study, we developed and validated the method for determination contents of myristicin in Myristica fragrans which was purchased from various regions of Korea. The average content of myristicin in Myristica fragrans was 2.10% with the validated HPLC analysis method.

• Geomechanics and Engineering
• /
• 제28권3호
• /
• pp.225-237
• /
• 2022

Settlement evaluation is important for shallow tunnels in big cities to estimate the settlement that occurs due to the excavation of twin tunnels. The majority of earlier research on analytical solutions, on the other hand, concentrated on calculating the settlement for a single tunnel. This research introduces a procedure to evaluate the settlement induced by the excavation of twin tunnels (two parallel tunnels). In this study, a series of numerical analysis were performed to validate the analytical solution results. Two geological conditions were considered to derive the settlement depending on each case. The analytical and numerical methods were compared, which involved considering many sections and conducting a parametric study; the results have good agreement. Moreover, a comparison of the 3D flat model and 2D (FEM) with the analytical solution shows that in the fill soil, the maximum settlement values were obtained by the analytical solution. In contrast, the values obtained by the analytical solution in the rock is more conservative than those in the fill. Finally, this method was shown to be appropriate for twin tunnels dug side by side by utilizing finite element analysis 3D and 2D (PLAXIS 3D and PLAXIS 2D) to verify the analytical equations. Eventually, it will be possible to use this approach to predict settlement troughs over twin tunnels.

• 산업기술연구
• /
• 제21권A호
• /
• pp.41-50
• /
• 2001

A comparison is made of the temperature distribution and heat loss from a trapezoidal profile fin using two different 3-dimensional methods. These two methods are analytical and finite difference methods. In the finite difference method 78 nodes are used for a fourth of the fin. A trapezoidal profile fin being the height of the fin tip is half of that of the fin base is chosen arbitrarily as the model. One of the results shows that the relative error in the total convection heat loss obtained by using 78 nodes in the finite difference method as compared to the heat conduction through the fin root obtained by analytic method seems to be good (i.e., -3.5%

• Journal of Electrical Engineering and Technology
• /
• 제8권6호
• /
• pp.1481-1486
• /
• 2013

In this paper, a new two dimensional (2D) analytical model of a Dual Material Gate tunnel field effect transistor (DMG TFET) is presented. The parabolic approximation technique is used to solve the 2-D Poisson equation with suitable boundary conditions. The simple and accurate analytical expressions for surface potential and electric field are derived. The electric field distribution can be used to calculate the tunneling generation rate and numerically extract tunneling current. The results show a significant improvement of on-current and reduction in short channel effects. Effectiveness of the proposed method has been confirmed by comparing the analytical results with the TCAD simulation results.

• Computers and Concrete
• /
• 제15권5호
• /
• pp.807-831
• /
• 2015

In the previous analytical studies on 2D reinforced concrete (RC) beam-column joints, the modified compression field theory (MCFT) and the strut-and-tie method (STM) are usually employed. In this paper, the limitations of these analytical models for RC joint applications are reviewed. Essentially for predictions of RC joint shear behaviour, the MCFT is not applicable, while the STM can only predict the ultimate shear strength. To eliminate these limitations, an improved STM is derived and applied to some commonly encountered 2D joints, viz., interior and exterior joints, subjected to monotonic loading. Compared with the other STMs, the most attracting novelty of the proposed improved STM is that all critical stages of the shear stress-strain relationships for RC joints can be predicted, which cover the stages characterized by concrete cracking, transverse reinforcement yielding and concrete strut crushing. For validation and demonstration of superiority, the shear stress-strain relationships of interior and exterior RC beam-column joints from published experimental studies are employed and compared with the predictions by the proposed improved STM and other widely-used analytical models, such as the MCFT and STM.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권6호
• /
• pp.278-286
• /
• 2005

Recently, high-speed centrifugal turbo-compressors have been under intensive research and development. Since, compared to conventional compressors, high-speed centrifugal compressors hive numerous qualities such as simple structure, light weight small size, and high efficiency, etc. In cope with such industrial demands, a high-speed brushless DC motor for a 50-kW, 70-krpm turbo-compressor was developed based on a 2-D analytical method, of which design was verified using the FE analysis. A prototype machine was also fabricated and tested to confirm the analytical design. Preliminarily obtained experimental data using the prototype mac]line shows the validity of the analytical approach.

• Journal of Electrical Engineering and Technology
• /
• 제13권4호
• /
• pp.1586-1595
• /
• 2018

For the problem that the complexity of 3-D modeling and multi parameter optimization, as well as the uncertainty of the winding factor of axial flux permanent magnet generator with coreless windings. The complex 3-D model was simplified into 2-D analytic model, and an analytical formula for the winding factor that adapting different coreless stator winding is proposed in this paper. The analytical solution for air-gap magnetic fields, no-load back EMF, electromagnetic torque, and efficiency are calculated by using this method. The multiple objective and multivariable optimization of the maximum fundamental and the minimum harmonic content of back EMF are performed by using response surface methodology. The proposed optimum design method was applied to make a generator. The generator was tested and the calculated results are compared with the proposed method, which show good agreements.

• 한국지반공학회논문집
• /
• 제16권4호
• /
• pp.5-16
• /
• 2000

본 연구에서는 지금까지 수행한 일련의 결과들에 근거한 지반력 계수와 극한 지반반력을 역해석적 방법으로 결정하고 이를 이용하여 비균질 지반에서의 비선형 수평거동을 예측할 수 있는 해석기법을 제안하고자 함이 목적이다. Chang이 제안한 해석기법은 비균질 지반의 비선형적인 거동을 예측하기에는 어려움이 있다. 이에 본 연구에서는 말뚝의 비선형 거동 예측을 위하여 Chang 모델에 p - y 곡선을 적용하는 복합적인 해석기법을 제안하고 해석 프로그램을 개발하였다. 그리고 본 해석기법의 적용성 검증을 위하여 모형실험 및 현장실험 결과와 상용 프로그램인 Pentagon2D을 이용한 해석 결과와 비교 검토하였다. 해석상에 이용한 지반반력 계수와 극한 지반반력은 균질지반에서 결정된 값을 비균질 지반에 적용하였으며, 본 해석기법에 의한 거동 예측결과는 모형실험 결과와 잘 일치하였다. 또한 현장실험과의 비교에서도 정도 높은 일치성을 보였다.

• 분석과학
• /
• 제7권3호
• /
• pp.395-402
• /
• 1994

본 연구에서는 두 종류의 기존 HPLC 베노밀 분석법 및 한 종류의 새로이 설정한 GC PFB 유도체화 베노밀 분석법을 도입하여 시중에 유통되는 국산 및 수입작물을 수거한 후 그 잔류도를 검색함과 동시에 각 분석법의 정확성, 정밀도, 회수율, 그리고 감도 등을 비교 평가하였다. 그 결과 GC PFB 유도체화분석법의 경우 회수율 및 검출 한계가 각각 95% 이상, $0.001{\mu}g/g$이었다. 그리고 각종 작물의 분석시 기존의 HPLC법의 경우 베노밀의 peak가 나타나는 retention time 시간대에 시료의 성분에 의한 peak도 동시에 나타날 수 있는 확률이 높아 오검출되는 사례가 많았으나 GC PFB 유도체화분석법은 베노밀을 유도체화한 후 GC에서 분석함으로써 오검출 판정결과를 보이는 시료는 없었다.