• 한국토양환경학회지
• /
• 제3권2호
• /
• pp.79-88
• /
• 1998

본 연구는 공기를 주입하여 매립지가스를 치환하고자 할 때 공기공급방법이 매립지가스제거에 미치는 영향을 검토하고자 실시하였다. 공기공급방법으로는 공기를 직접 불어넣는 방법과 매립지가스를 추출함으로써 대기중의 공기가 내부로 유입되도록 하는 방법을 사용하였다. 또한 한 주입정에서 공기를 주입하고 동시에 다른 추출정에서 가스를 추출하는 공정도 실시하여 운전모드에 따른 매립지가스 제거 효율을 비교검토하였다. 공기주입 및 가스추출시 유량은 15$\textrm{m}^3$/min으로 동일하였다. 추출모드나 주입/추출모드로 운전하는 것보다 공기주입모드로 운전하는 것이 매립지가스 제거에 가장 효과적이었으며 추출모드는 매립지가스 제거에 가장 적합하지 못하였다. 공기주입과 추출을 동시에 실시하는 경우에도 주입모드에 비하여 매립지가스 제거효율을 크게 향상시키지는 못하였다.

• 한국음향학회지
• /
• 제40권1호
• /
• pp.38-45
• /
• 2021

본 연구는 함정 추진기에 적용되고 있는 공기분사에 의한 수중방사소음 저감기술에 대한 연구기반을 마련하고자 캐비테이션 터널에서 단순화된 모형을 이용하여 공기분사에 의한 캐비테이션과 소음의 변화에 대하여 연구하였다. 추진기 날개와 유사한 특성을 나타내는 3차원 타원형 수중익에 공기분사 위치와 분사량을 조절할 수 있는 공기분사시스템을 제작하였으며 캐비테이션 터널 시험조건을 조절하여 수중익에 다양한 형태의 캐비테이션을 모사하고 공기분사에 따른 캐비테이션과 소음특성의 변화를 실험적으로 분석하였다. 공기분사 위치 및 분사량에 따라 캐비테이션 및 소음특성이 달라짐을 확인하였다. 이는 추진기에 공기분사 기술을 적용하기 위해서는 캐비테이션의 발생위치, 거동에 따른 공기 분사위치 및 분사량의 최적화가 필요함을 의미한다.

• 한국자동차공학회논문집
• /
• 제11권5호
• /
• pp.15-21
• /
• 2003

The liquid phase LPG injection engine is a new technology to make good use of LPG as a clean energy. However, it is difficult to precisely control air/fuel ratio in the system because of variation of fuel composition, change of temperature and flash boiling injection mechanism. This study newly suggests an injector control logic for liquid phase LPG injection systems. This logic compensates a number of effects such as variations of density, stoichiometric air/fuel ratio, injection delay time, injection pressure, release pressure which is formed by flash boiling of fuel at nozzle exit. This logic can precisely control air/fuel ratio with only two parameters of intake air flow rate and injection pressure without considering fuel composition, fuel temperature.

• 한국해양공학회지
• /
• 제14권3호
• /
• pp.84-89
• /
• 2000

The purpose of this study is to investigate the combustion emission characteristics by the effect of secondary air injection and variation of the excess air ratio in combustion field of model gas turbine combustor. For this purpose, mean temperature, CO, $CO_2$, $O_2$ and HC concentrations were measured by changing excess air ratio and secondary air injection. As a result of this study, mean temperature was decreased and CO, HC emission increased by increasing the excess air ratio of secondary air. Therefore, this results showed the secondary air injection effected strongly on the flame structure and combustion emission characteristics.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 춘계학술대회 논문집
• /
• pp.171-176
• /
• 2000

This purpose of this study is to investigate the combustion emission characteristics on the effect of secondary air injection in combustion field of model gas turbine combustor changing excess air ratio. For this purpose, meantemperature, CO, CO2, O2 and HC concentration were measured by changing excess air ratio and secondary air injection. As a result of this study, meantemperature, CO2 emission was decreased and CO emission increased by increasing the excess air ratio of secondary air. therefore, This paper showed the effect of Secondary air injection on flame structure, combustion emission characteristics.

• Geomechanics and Engineering
• /
• 제13권1호
• /
• pp.1-23
• /
• 2017

A coupled liquid-gas-solid three-phase model, linking two numerical codes (TOUGH2/EOS3 and $FLAC^{3D}$), was firstly established and validated by simulating an in-situ air flow test in Essen. Then the coupled model was employed to investigate responses of multiphase flow and soil skeleton deformation to compressed air or freshwater injection using the same simulation conditions in an aquifer of Tianjin, China. The simulation results show that with injecting pressurized fluids, the vertical effective stress in some area decreases owing to the pore pressure increasing, an expansion of soil skeleton appears, and land uplift occurs due to support actions from lower deformed soils. After fluids injection stops, soil deformation decreases overall due to injecting fluids dissipating. With the same applied pressure, changes in multiphase flow and geo-mechanical deformation caused by compressed air injection are relatively greater than those by freshwater injection. Furthermore, the expansion of soil skeleton induced by compressed air injection transfers upward and laterally continuously with time, while during and after freshwater injection, this expansion reaches rapidly a quasi-steady state. These differences induced by two fluids injection are mainly because air could spread upward and laterally easily for its lower density and phase state transition appears for compressed air injection.

• 대한기계학회논문집B
• /
• 제40권8호
• /
• pp.503-510
• /
• 2016

일반적으로 연소로는 연료의 연소과정에서 NOx, CO등의 공해물질을 배출한다. 본 연구는 소각연소로를 대상으로 2차 공기를 연소가스 흐름의 역방향으로 주입시키는 방법의 NOx 및 CO 배출특성에 대한 연구를 수행하였다. 연구의 주요변수는 1, 2차 공기의 유량비와 2차 공기의 투입 방향으로 설정하였다. 변수에 따른 NOx 및 CO 배출특성을 묘사하기 위해서 축소모형실험 연구를 수행하였다. 실험결과 1차 공기유량이 감소하고 2차 공기유량이 증가할수록 NOx가 감소되다가 일정 유량비 이상에서 다시 NOx가 다소 증가하는 형태가 나타났다. 역방향으로 빠른 유속의 2차 공기가 투입될 때 연소로 내부에 유동 재순환이 발생하여 혼합이 증가하고 이로 인해서 온도 영역이 고르게 분포되는 것으로 나타났으며 그 결과로서 thermal NOx의 저감 효과를 확인할 수 있었다. CO는 2차 공기가 역방향에서 높은 비율로 투입되는 조건이외에서는 측정되지 않았다. 측정된 경우도 CO의 농도는 2 ppm 이내로 안정적인 연소 조건으로 나타났다.

• 한국분무공학회지
• /
• 제26권2호
• /
• pp.96-103
• /
• 2021

In order to improve the overall efficiency and meet the emission regulations of boiler systems, the heat exchanging methods between inlet air and exhaust gas have been used in boiler systems, named as the waste-heat-recovery condensing boiler. Recently, to further improve the overall efficiency and to reduce the NOx emission simultaneously, the concept of the water injection into the inlet air is introduced. This study suggests the models for the optimized design parameters of water injection for waste-heat-recovery condensing boilers and performs the analysis regarding the water injection amount and droplet sizes for the optimized water injection. At first, the required amount of the water injection was estimated based on the 1^st law of thermodynamics under the assumption of complete evaporation of the injected water. The result showed that the higher the inlet air and exhaust gas temperature into the heat exchanger, the larger the amount of injected water is needed. Then two droplet evaporation models were proposed to analyze the required droplet size of water injection for full evaporation of injected water: one is the evaporation model of droplet in the inlet air and the other is that on the wall of heat exchanger. Based on the results of two models, the maximum allowable droplet sizes of water injection were estimated in various boiler operating conditions with respect to the residence time of the inlet air in the heat exchanger.

• Journal of Mechanical Science and Technology
• /
• 제16권7호
• /
• pp.950-958
• /
• 2002

The combustion characteristics of a low NOx burner using reburning technology have been experimentally studied. The return burner usually has three distinct reaction zones which include the primary combustion zone, the reburn zone and the burnout zone by provided secondary air. NOx is mainly produced in a primary combustion zone and a certain portion of NOx can be converted to nitrogen in the rebury zone. In the burnout zone, the unburned mixtures are completely oxidated by supplying secondary air. Liquefied Petroleum Gas (LPG) was used as main and reburn fuels. The experimental parameters investigated involve the main/reburn fuel ratio, the primary/secondary air ratio, and the injection location of rebury fuel and secondary air. When the amount of return fuel reaches to the 20-30% of the total fuel used, the overall NO reduction of 50% is achieved. The secondary air is injected by two different ways including vertical and parallel injection. The injector of secondary air is located at the downstream region of furnace for a vertical-injection mode, which is also placed at the inlet primary-air injection region for a parallel-injection mode. In case of the vertical injection of the secondary air flow, the NOx formation of stoichiometric condition at a primary combustion zone is nearly independent of the rebury conditions (locations, fuel/air ratios) while the NOx emission of the fuel-lean condition is considerably influenced by the reburn conditions. In case of the parallel injection of the secondary air, the NOx emission is sensitive to the air ratio rather than the fuel ratio and the reburning process often coupled with the multiple air-staging and fuel-staging combustion processes.

• 한국정밀공학회지
• /
• 제19권7호
• /
• pp.80-87
• /
• 2002

Liquefied petroleum gas (LPG) is used in spark ignition (SI) engines. Fuel injection rate of an injector is affected by fuel temperature and pressure in LPG liquid injection systems for either a multi-point-injection (MPI) or a direct injection (DI) engine. Even fuel injection conditions are varied, the air-fuel ratio should be accurately controlled to reduce exhaust emissions. In this study, a correction factor fur the fuel injection rate of an injector is derived from density ratio and pressure difference ratio. A compensation method of injected fuel amount is proposed for a fuel injection control system. The experimental results for the LPG liquid injection system in a SI engine show that this system works well fur a full range of engine speed and load condition, and the air-fuel ratio is accurately controlled by the proposed correction factor.