• Journal of Powder Materials
• /
• v.25 no.2
• /
• pp.99-103
• /
• 2018

Spherical monosized pure aluminum (Al) particles are successfully fabricated by the pulsated orifice ejection method (POEM). The surface reaction between Al and the graphite crucible is investigated by analysing the microstructure and chemical composition of the materials. No significant chemical reaction occurs between Al and the graphite owing to the crystalline Al oxide (${\gamma}-Al_2O_3$) layer generated in the initial state. The ${\gamma}-Al_2O_3$ layer is clearly observed in all regions between the Al particles and graphite via transmission electron microscopy and confirmed by the selected area diffraction pattern. The morphology of the ${\gamma}-Al_2O_3$ layer perfectly follows the surface morphology of the graphite crucible, which showed nanoscale roughness. This implies that molten Al could not directly contact graphite even though the surface of the crucible became rough to some extent. However, this passivation phenomenon allowed the successful fabrication of monosized pure Al particles. Therefore, POEM is a useful process at least to manufacture monosized pure Al particles.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.4
• /
• pp.155-158
• /
• 2016

Thermal conductivity is a very important factor for applicability and reliability in electrical devices. In this study, Al/graphite composite is fabricated by a mechanical alloying and heat-treatment and its physical properties are characterized. The XRD peak intensity of the $Al_4C_3$ ceramic phase observed in the heat-treated Al/graphite composite increased with heat-treatment temperature and time. The thermal conductivity of the heat-treated Al/graphite composite sample was very lower than that of the pure Al sample, and increased with heat-treatment temperature and time.

• Journal of Powder Materials
• /
• v.27 no.4
• /
• pp.300-304
• /
• 2020

In this paper, a durability study is presented to enhance the mechanical properties of an Fe-Si-Al powder-based magnetic core, through the addition of graphite. The compressive properties of Fe-Si-Al-graphite powder mixtures are explored using discrete element method (DEM), and a powder compaction experiment is performed under identical conditions to verify the reliability of the DEM analysis. Important parameters for powder compaction of Fe-Si-Al-graphite powder mixtures are identified. The compressibility of the powders is observed to increase as the amount of graphite mixture increases and as the size of the graphite powders decreases. In addition, the compaction properties of the Fe-Si-Al-graphite powder mixtures are further explored by analyzing the transmissibility of stress between the top and bottom punches as well as the distribution of the compressive force. The application of graphite powders is confirmed to result in improved stress transmission and compressive force distribution, by 24% and 51%, respectively.

• Journal of Korea Foundry Society
• /
• v.7 no.1
• /
• pp.38-44
• /
• 1987

The spiral fluidity of graphite-dispersed Al-Si alloys has been investigated as a function of contents of Si and graphite, and of particle size of graphite. The dispersion of uncoated graphite is carred out by the vortex process of preheat-treated graphite into molten metal. The fluidity of hyper-eutectic Al-Si alloys is observed to the better than that of hypo-eutectic ones. In the case of graphite-dispersed Al-Si alloys they fluidity increases in hypo-eutectic alloys and decreases in hyper-eutectic ones in comparison with that of the corresponding undispersed alloys. Fluidity decreases with an increase of amount of dispersed graphite particles and inversely proportional to the total surface area of graphite particles.

• Journal of Korea Foundry Society
• /
• v.3 no.4
• /
• pp.239-247
• /
• 1983

CV graphite cast iron has been studied and generally known to have properties close to the average values of those between flake and spheroidal graphite cast iron. However, the thermal diffusivity of CV graphite cast iron is much larger than that of the average value of those between flake and spheroidal graphite cast iron. In this study, an easy production method of CV graphite cast iron with small additions of a Al-Cu which is known as the element of the graphitization was investigated. The effects of hold time and of Al-Cu additions after the treatments with spheroidizer (Fe-Si-Mg alloy) were also investigated. Increasing the additions of a Al-Cu alloy, the holding time to form a CV graphite cast iron was decreasing. Tensile strength and thermal diffusivity (flash method) were measured in order to find the changes of the mechanical properties and the physical properties. Spheroidal, CV, and flake graphite cast iron have tensile strengths 46.44, 38.29, and $27.29\;kg/mm^2$ and thermal diffusivities $3.95{\times}10^{-6,}$ $8.41{\times}10^{-6}$, $8.81{\times}10^{-6}m^2/sec$, respectively at room temperature.

• Journal of Korea Foundry Society
• /
• v.1 no.2
• /
• pp.2-9
• /
• 1981

Graphite spheroidization and scaling resistance of cast iron containing 5-10% Al were investigated. It is impossible to obtain spheroidal graphite in cast iron containing Al with 8 % and over, but possible to obtain spheroidal graphite even in cast iron with an Al content of about 10 % by increasing Si content. In the scaling test carried out under the heating condition of $950^{\circ}C$ in air for total of 50 hours, the scaling resistance of cast iron containing Al with 8 % and over was remarkably superior, and also spheroidal graphite cast iron was superior to flake graphite cast iron. The scale became thinner more compacts and more protective with increasing Al content.

• Journal of Korea Foundry Society
• /
• v.21 no.2
• /
• pp.119-126
• /
• 2001

Al/15%Gr. composite have been manufactured by mixing, compacting, and extruding aluminium powder and graphite powder. Then, Al-6%Si/x%Gr., Al-12%Si/x%Gr., and Al-18%Si/x%Gr.(x: 0, 2, 4, 6, 8) composites have been manufactured by remelting the extruded materials(Al/15%Gr.), Al-33.3%Si alloy, and Al ingot, etc. We conducted experiments to chracterize the microstructure, and damping properties and hardness. The result of microstructure experiment on Al-x%Si/y%Gr. composites reveals the good dispersion of graphite. As to Al-Si/y%Gr. composites, the more the graphite contents, the less the tensile strength. And the tensile strength varied according to contents of Si: with its highest value in Al-18%Si/y%Gr. composites and lowest in Al-6%Si/y%Gr. composites. As to Al-x%Si/y%Gr. composites, the more the contents of graphite, the more the vibration damping properties. And we can get the highest vibration damping rate in Al-12%Si/y%Gr. composites which matrix structure is an eutectic component.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.6
• /
• pp.462-466
• /
• 2012

In this paper, heat-releasing composite sheets made of AlN, graphite, Al powder and acryl binder as thermoset were prepared using tape casting method. The crystal structure, morphology, thermal conductivity of heat-releasing composite sheet were measured by using X-ray diffractometer, field emission-scanning electron microscopy and laser flash instrument. It was found thermal conductivity of sheet was decided by solid content, composition including AlN, graphite, Al in heat-releasing composite sheets. As a result, 4.56 W/mK of thermal conductivity could be obtained by using LFA 447.

• Journal of the Korean Ceramic Society
• /
• v.49 no.4
• /
• pp.369-374
• /
• 2012

Based on the structure feature of a tree, a cylindrical $Ti_2AlC$/graphite layered composite has been fabricated through heat treating a graphite column and six close-matched thin wall $Ti_2AlC$ cylinders bonded with the $Ti_2AlC$ powders at $1300^{\circ}C$ and low oxygen partial pressure. SEM examination reveals that the bond interlayers between cylinders or that between cylinder and column are not fully dense without any crack formation. During the compressive test, the strain of the $Ti_2AlC$/graphite layered composite is about twice higher than that of the monolithic $Ti_2AlC$ ceramic, and the compressive strength of the layered composite is 348 MPa. The layered composite show the noncatastrophic fracture behaviors due to the debonding and shelling off of the layers, which are different from the monolithic $Ti_2AlC$ ceramic. The mechanism of the improved deformation capacity and noncatastrophic failure modes are attributed to the presence of the central soft graphite column and cracks deflection by the bond interlayers.

• Journal of Korea Foundry Society
• /
• v.6 no.1
• /
• pp.5-11
• /
• 1986

The Wear Characteristics of Al-Si alloys were investigated with various Si contents by using the not-dispersed alloys and uncoated-graphite dispersed alloys. Uncoated-graphite dispersions were accomplished by Vortex method carrying 1 hr. heating at $400^{\circ}C$ on uncoated-graphite. Wear loss were increased by increasing Si contents at the elevated final load. Hyper-eutectic alloys showed higher wear resistance values at the small final load of 2.1Kg and 3.2Kg, but at the more increased final load, hypo-eutectic alloys showed higher wear resistance values than hyper-eutectic alloys. The property of wear resistance of uncoated-graphite dispersed Al-Si alloys showed more good values than not-dispersed alloys. This peroperty of increased war resistance were resulted from lubricating action of dispersed graphite.