• Transactions of Materials Processing
• /
• v.17 no.4
• /
• pp.284-291
• /
• 2008

It was investigated that two rods of aluminum can be welded by hot extru-pressure welding method with stepped welding dies, and that the welding pressure and metal flow on the welding surface were analyzed by computer simulation according to the stepped shapes of welding dies. It was known by computer simulation that welding pressure on the welding section of rods welded using stepped welding dies could be higher than the welding pressure of aluminum rods without using stepped welding die. And it was known by experiments that two rods of aluminum can be welded on the end sections by hot extru-pressure welding method using stepped welding dies without relative rotational movement of contacted aluminum rods in the case of friction welding of rods.

• Transactions of Materials Processing
• /
• v.19 no.8
• /
• pp.460-467
• /
• 2010

It was studied that two plates of aluminum can be welded by extru-riveting experiments with extru-rivet welding dies, and that the welding strength and metal flow on the welding section were analyzed by computer simulation according to the welding variable such as the diameter of extrusion insert dies. It was known by computer simulation that welding strength on the welding section of plates could be influenced by the diameter of extrusion insert dies. And it was known by experiments that two plates of aluminum can be welded on a spot point on aluminum plate by extru-rivet welding process, and that welding strength is higher and higher if the diameter of extrusion insert die is smaller and smaller, and that welding strength is the highest when diameter of extrusion insert dies is ${\emptyset}4.2$mm in the case that the diameter of rivet is 5 mm, when aluminum 5052 two plates with 1.5 mm thickness and one plate with 3mm thickness for rivet plate are used as welding material.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.1 no.1
• /
• pp.39-49
• /
• 2009

The use of high-strength aluminum alloys is increasing in shipbuilding industry, particularly for the design and construction of war ships, littoral surface craft and combat ships, and fast passenger ships. While various welding methods are used today to fabricate aluminum ship structures, namely gas metallic arc welding (GMAW), laser welding and friction stir welding (FSW), FSW technology has been recognized to have many advantages for the construction of aluminum structures, as it is a low-cost welding process. In the present study, mechanical properties of friction stir welded aluminum alloys are examined experimentally. Tensile testing is undertaken on dog-bone type test specimen for aluminum alloys 5083 and 5383. The test specimen includes friction stir welded material between identical alloys and also dissimilar alloys, as well as unwelded (base) alloys. Mechanical properties of fusion welded aluminum alloys are also tested and compared with those of friction stir welded alloys. The insights developed from the present study are documented together with details of the test database. Part of the present study was obtained from the Ship Structure Committee project SR-1454 (Paik, 2009), jointly funded by its member agencies.

• Journal of Welding and Joining
• /
• v.24 no.5
• /
• pp.67-73
• /
• 2006

Laser welding is suitable for welding to the aluminum alloy sheet. In order to apply the aluminum laser welding to production line, parameters should be optimized. In this study, the optimal welding condition was searched through the genetic algorithm in laser welding of AA5182 sheet with AA5356 filler wire. Second-order polynomial regression model to estimate the tensile strength model was developed using the laser power, welding speed and wire feed rate. Fitness function for showing the performance index was defined using the tensile strength, wire feed rate and welding speed which represent the weldability, product cost and productivity, respectively. The genetic algorithm searched the optimal welding condition that the wire feed rate was 2.7 m/min, the laser power was 4 kW and the welding speed was 7.95 m/min. At this welding condition, fitness function value was 137.1 and the estimated tensile strength was 282.2 $N/mm^2$.

• Transactions of Materials Processing
• /
• v.19 no.8
• /
• pp.452-459
• /
• 2010

It was investigated that two plates of aluminum can be welded by hot extru-shear welding process with extru-shear welding dies, and that the welding strength and metal flow on the welding section were analyzed by computer simulation according to the welding variables such as inclined angle of cutter and overlapped length of plates and temperature of plates. It was known by computer simulation that welding strength on the welding section of plates could be influenced by the inclined angle of cutter and overlapped length of plates and temperature of plates. And it was known by experiments that two plates of aluminum can be welded on the end sections by hot extru-shear welding process using extru-shear welding dies, and that welding strength is the highest when inclined angle of dies is $70^{\circ}$, and overlapped length is 1.2 mm, and temperature is $520^{\circ}$, when aluminum 5052 two plates with 1.6 mm thickness are used as welding material.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.211-215
• /
• 2005

The binary Al-Mg alloys are the basis for the 5000 series of non-heat-treatable aluminum alloys. In general, 5000 series of aluminum alleys have a high strength, good welding characteristics and a high resistance to corrosion, especially under the seawater. Thus the aluminum alloys are adopted in the hull material of hovercraft that is required light in weight as well as high strength. It is very important that the weldability problem of these alloys caused by high thermal conductivities welding deformation, porosity and so on. in this study, auto-welding equipment was applied for aluminum welding automation. Also, optimal welding data were studied by investigating welding characteristics for various shapes of weldment to use Al 5083 that is representative structural materials of the 5000 series of aluminum alloys.

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.239-239
• /
• 2000

Automobile manufacturers have employed resistance spot welding(RSW) to join steel sheets for structural rigidity o automobile body. Driven by the need to reduce weight and fuel consumption, car companies have been evaluating aluminum intensive vehicles(AIVs) as a way to reduce vehicle weight without downsizing. During the transition from all steel-construction vehicle body to aluminum intensive body, joining aluminum to steel sheets emerges as a serious contender in automobile body. This paper deals with application of transition material to RSW aluminum to steel. Placing transition material insert between the aluminum/steel interface was found very effective to overcome incompatibility between aluminum and steel. Use of transition insert allows for two separate weld muggets to be formed in their respective aluminum/ aluminum and steel/ steel interfaces. This RSW process was monitored with the aid of dynamic resistance sampling. Typical patterns in sampled dynamic resistance curves indicated formation of sound nugget. (Received February 28, 2000)

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.112-118
• /
• 2000

Automobile manufacturers have employed resistance spot welding(RSW) to join steel sheets for structural rigidity of automobile body. Driven by the need to reduce weight and fuel consumption, car companies have been evaluating aluminum intensive vehicles(AIVs) as a way to reduce vehicle weight without downsizing. During the transition from all steel-construction vehicle body to aluminum intensive body, joining aluminum to steel sheets emerges as a serious contender in automobile body. This paper deals with application of transition material to RSW aluminum to steel. Placing transition material insert between the aluminum/steel interface was found very effective to overcome incompatibility between aluminum and steel. Use of transition insert allows for two separate weld nuggets to be formal in their respective aluminum/aluminum and steel/steel interfaces. This RSW process was monitored with the aid of dynamic resistance sampling. Typical patterns in sampled dynamic resistance curves indicated formation of sound nugget.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.127-140
• /
• 1994

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. In the resistance spot welding processes the size of molten nugget is a criterion to assess weld quality. Many research have founded on measuring weld nugget size at the same time monitoring welding process parameters such as dynamic resistance and electrode movement. With increasing demand of energy saving, many efforts were made to employ aluminum alloys that are lighter than steel and have relatively equivalent strength to steel in the automobile industry. In this paper, spot weldability of aluminum alloys for various welding conditions were examined by series of experiments. One of the 6000 series (Mg-Si) aluminum alloy, 6383-T4 was chosen, which is currently considered as a substitute for the galvanized steel. Dynamic resistance, electrode movement and corresponding nugget size were observed and compared to the case of steel. Finally, resistance spot welding of dissimilar material (galvanized steel-aluminum alloy) was attempted.

• Journal of Welding and Joining
• /
• v.31 no.1
• /
• pp.21-25
• /
• 2013

Aluminum alloy, Al5083-O, is one of candidate materials for the LNG storage tank, because of its excellent weldability, cryogenic characteristics, and corrosion resistance. The good weldability of Al5083-O is very important in LNG storage tank manufacturing. In this study, high current metal inert gas(MIG) welding process was used to get one pass welding of thick plate aluminum alloy. Bead on plate(BOP) welding was performed to evaluate the effect of welding conditions on the height of bead and depth of penetration. The optimum welding conditions were derived to get one pass welding of the thickness of 14.5mm. The mechanical properties of the welded joint were evaluated. The cross-sectional macro test, tensile test, and bending test satisfied the class rule.