• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.200-204
• /
• 2008

The curing kinetics of diglycidyl ether of bisphenol F (DGEBF) with an asymmetric cycloaliphatic amine curing agent were examined by thermal analysis in both isothermal and dynamic curing conditions. From the residual curing of the samples partially cured in isothermal condition and from the dynamic curing with various heating rates, it was found that there exist two kinds of reactions such as at low temperature and at high temperature regions. It was thus also found that the cure parameters obtained from the isothermal curing kinetic model hardly estimate experimental results for a degree of cure larger than 0.6. The activation energies and frequency factors of these two kinds of reactions were obtained from the dynamic curing experiments with various heating rates. From the curing analysis, it was verified that the total cure kinetics for low degrees of cure is dominated by the cure reaction in the low temperature region.

• Textile Coloration and Finishing
• /
• v.11 no.6
• /
• pp.7-17
• /
• 1999

Aminophosphazene derivatives were prepared from hexachlorocyclotriphosphazene and used for the curing agents of epoxy resins. The effect of the curing agent on the dynamic viscoelastic properties, flame proofing, and heat resistance of the cured epoxy resins were investigated and compared with those for the epoxy resins cured with aliphatic and aromatic amines. The epoxy resin cured by 1,1-diamino-3,3,5,5-tetrachlorocyclotriphosphazene showed the highest storage modulus and glass transition temperature when cured at 19$0^{\circ}C$ for 6 hours. The epoxy resins cured with phosphazene derivatives showed superior flame proofing to those with aliphatic amine and aromatic amine. Particularly it is an effective curing agent for epoxy resins to enhance the storage modulus, flame proofing and resistance to heat.

• Elastomers and Composites
• /
• v.35 no.1
• /
• pp.12-18
• /
• 2000

With growing concerns of environment and due to strengthening the government regulations on volatile organic compounds(VOC) the coatings industries are developing new technologies to reduce the amount of VOC released from coatings. In this study. a water soluble curing agent of amino-epoxy adduct was synthesized and its structure was identified by FT-IR, GPC and TG/DTA. The mechanical properties of the new curing agent in combination of KER-828 and KER-500 were investigated respectively. As an experimental result, the drying time of KER-828 was faster than that of KER-500 but the adhesion and impact strength of KER-500 was better than that of KER-828.

• Elastomers and Composites
• /
• v.52 no.4
• /
• pp.266-271
• /
• 2017

This study describes the influence of the amount of curing agent and curing temperature on the kinetics of polyurethane elastomers. The urethane prepolymer series was prepared by reacting toluene diisocyanate with polytetramethylene ether glycol at $80^{\circ}C$ for 1 h, and 4,4'-methylene bis(2-chloroaniline) was used as the curing agent. The ratio of the amine group of the curing agent to the isocyanate group of the urethane prepolymer was controlled from 0.85 to 1.05 at curing temperatures ranging from 80 to $120^{\circ}C$. The curing rate of the urethane prepolymer was monitored by observing the change in heat flow during the curing process using differential scanning calorimetry (DSC). As either the content of curing agent or the curing temperature was higher, the conversion rate to the polyurethane elastomer was high. The DSC results were compared with those obtained from using real-time FT-IR.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.164-165
• /
• 2021

To prepare the good-adherent and weather-resistant acrylic resin coatings, acrylic resin was prepared by a radical polymerization. Glass transition temperature(Tg) of the acrylic copolymer was fixed at 30℃ and the contents of tertiary amine monomer(DMAEMA) was varied to be 5, 10, 15, 20 wt% respectively. γ-Glycidoxypropyltrimethoxysilane(GPTMS) containing epoxy group was used for curing agents and di-n-butyltindilaurate(DBTDL) was used for drying accelerator. The equivalent ratio of amine to epoxy was 1:1. The prepared coatings exhibited excellent adhesion to various substrates, and various physical properties of the coatings were satisfactory. The gloss retention and color difference were improved at low tertiary amine concentration. The coatings containing 10wt% tertiary amine concentration have especially good weather resistant properties.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.4
• /
• pp.424-426
• /
• 2001

• Bulletin of the Korean Chemical Society
• /
• v.22 no.12
• /
• pp.1393-1396
• /
• 2001

• International Journal of Ocean System Engineering
• /
• v.3 no.2
• /
• pp.102-110
• /
• 2013

The purpose of this study was to improve the properties of epoxy resin using titanium oxide nanoparticles. The effects of particle weight fraction, dispersion agent, and curing agents with different molecular weights on the thermal and mechanical properties of titanium-oxide-reinforced epoxy resin were investigated. In addition, the effect of the particle dispersion condition on the mechanical properties of nanocomposites was studied. As a result, it was found that the glass transition temperature of film-shaped nanocomposites decreased with an in-crease in the nanoparticle content. Because nanoparticles interrupted the cross linkage between the epoxy resin and the amine curing agent, the cross-link density of the epoxy became lower and led to a decrease in $T_g$ in the nanocompo-sites. The tensile strength and modulus in film-shaped nanocomposites also increased with the particles content. But in the case of dog-bone-shaped nanocomposites, the values were not similar to the trend for the film-shaped nanocompo-sites. This was probably a result of the different nanoparticles dispersions in the epoxy resins resulting from the respective-thicknesses of the film and dog-bone-shaped samples.

• Composites Research
• /
• v.34 no.3
• /
• pp.180-185
• /
• 2021

Due to the formation of random three dimensional network structure, which cause a lot of scattering of phonons, the thermal conductivity is low when the liquid crystalline epoxy is cured with amine-based curing agent. This problem is solved by using a cationic initiator that can make mesogen groups to be stacked structure. In this experiment, the thermal stability is compared by investigating the activation energy of isothermal decomposition through TGA of an epoxy using an amine-based curing agent and a cationic initiator. As a result, the energy of the activation of the epoxy using a cationic initiator is high. Compared with the previous experiments, the thermal stability is similar to the thermal conductivity.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.214-217
• /
• 2004

The cure kinetics of blends of epoxy(tetraglycidyl-4,4'-diaminodiphenylmethane ; TGDDM)/curing agent(diaminodiphenyl sulfone ; DDS) resin with amine terminated polyetherimide-CTBN-amine terminated polyetherimide triblock copolymer(ABA) were studied using differential scanning calorimetry under isothermal conditions to determine the reaction parameters such as activation energy and reaction constants. By increasing the amount of ABA in the blends, the final cure conversion was decreased. Lower values of the final cure conversions in the epoxy/ABA blends indicated that ABA hinders the cure reaction between the epoxy and curing agents. 1be value of the reaction order, m, for the initial autocatlytic reaction was not affected by blending ABA with epoxy resin, and the value was approximately 1.0. The value of n for the nth order component in the autocatalytic analysis was increased by increasing the amount of ABA in the blends, and the value increased from 2.0-3.4. A diffusion controlled reaction was observed as the cure conversion increased and the rate equation was successfully analyzed by incorporating the diffusion control term for the epoxy/DDS/ABA blends.