• The Journal of the Korea Contents Association
• /
• v.10 no.10
• /
• pp.68-77
• /
• 2010

In the case of operating steam generators for long periods in nuclear power plants, sludge is accumulated inside the steam generator. This phenomenon could adversely affect the operation of the steam generator. This paper is about the design of a sludge washing apparatus which can remove the sludge efficiently and the control methods of the apparatus. In this paper, to design the sludge washing apparatus, firstly, we design nozzles for spraying high-pressure water through applying mathematical models and lab tests. Secondly, we establish the mathematical theory for performance parameters required to drive the sludge washing apparatus. Thirdly, we design physical structures of the apparatus based on the established performance parameters. Finally, we present the control methods of the apparatus. The sludge washing apparatus presented in this paper moves along the walls of the steam generator according to cracks in the tube array, and spray the high pressure water to remove the sludge. By this way, a relatively large amount of sludge formed in the inner surfaces can be washed very effectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1133-1136
• /
• 2004

The structures of airplane consist of sheet metal part, heavy machined part, and so on, which generate enormous amounts of cutting chip when these parts are machined. The cutting chip detoriorates the part quality and production efficiency. Therefore, cutting chip collecting apparatus is necessary for better quality and efficiency. In this study, blowing type cutting chip collecting apparatus was newly proposed and the concept design of the apparatus was examined through numerical analysis. Computations using the mass-averaged implicit 2D Navier-Stokes equations are applied to predict the nozzle flow field. The standard k-e turbulent model are employed to close the governing equations. Consequently, this study shows that the suggested blowing type cutting chip collecting apparatus can be alternative to existing expensive chip collecting apparatus.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.11
• /
• pp.2001-2005
• /
• 2008

This paper presents a design of a simulation apparatus to evaluate an operational control algorithm for the PRT system. PRT systems require very short headways to increase the line capacity and a very reliable vehicle control algorithm for avoidance of the impact between vehicles. Therefore, it can be said that the development of an reliable operational control algorithm for the PRT systems is much more important than that of the hardware configurations. In this paper an apparatus is proposed which is composed of virtual vehicles, a central control system, a man-machine interface and monitoring device, making it possible for the designed operational control algorithm to be implemented and tested. For the test of the proposed apparatus a test operational control algorithm is designed and the experimental results show the effectiveness of the proposed simulation apparatus for test and evaluation of the PRT operational control algorithms.

• Journal of the Korea Furniture Society
• /
• v.25 no.4
• /
• pp.239-249
• /
• 2014

Color is an important subject of interest for cognitive developmental stages of children and it also correlate to emotional and physical development. Children can acquire concept of color by 'play'. Color play can be experienced to children through diversity activity and theses activities contain creative craft art activity. The color-paly with art activity for kids can be called 'kids color-design play'. Recently, indoor playgrounds are rapidly grow-up because parent's concern degree that about play activity get higher. The indoor playground being enlargement and it contains various paly contents. Color-design play is also enacted animatedly in kids indoor playground. The great part of color-design plays are enacted through program that needs teaching. On the other hand, color-design play facility that children can play spontaneously is not composed sufficiently. Therefore this study aim at design proposal of 'Kids color-design playground apparatus' in indoor playground.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.8
• /
• pp.54-63
• /
• 2001

Rapid Prototyping(RP) techniques have their unique characteristics according to the working principles: stair-stepped surface of a part due to layer-by-layer stacking, low build speed caused by point-by-point or line-by-line solidification to build one layer, and additional posts processing to improve surface roughness, so high cost is required to introduce and to maintain the RP apparatus. The objective of this study is to develop a new RP process, Variable Lamination Manufacturing by using expandable polystyrene foam sheet as part material(VLM-S), and to design an apparatus for implementation of the process. So, the process parameters and design criterions of the apparatus were defined and the techniques were proposed to satisfy the design criterion. Based on the results, a knob-shape, pyramid shape. and a solid block were fabricated on the apparatus in which unit shape part(USP) was generated for building each layer.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.5
• /
• pp.315-324
• /
• 2021

A solid state transformer (SST) that can interface an MVAC of three-phase 13.2 kV and a 1.5 kV DC distribution. SST consists of an AC/DC converter and a DC/DC converter with a high-frequency isolation transformer (HFIT). The AC/DC converter consists of cascaded NPC full-bridge to cope with the MVAC. The DC/DC converter applies a quad active bridge (QAB) topology to reduce the number of the HFIT. Topology analysis and controller design for this specific structure are discussed. In addition, the insulation of HFIT used in DC/DC converters is considered. The discussion is validated using a 300 kVA three-phase SST prototype.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.2
• /
• pp.95-105
• /
• 2002

In order to reduce the lead-time and cost, the technology of rapid prototyping (RP) has been widely used. However, RP technologies have disadvantageous characteristics according to their working principle: low building speed, high cost for introduction and maintenance of RP apparatus, stair-stepped surface and additional post processing. A new rapid prototyping process, as a transfer type of Variable Lamination Manufacturing by using expandable polystyrene room (VLM-ST), has been developed to reduce building lime. apparatus cost including the introduction and the maintenance and additional post-processing. The objective of this study is to propose a VLM-ST process and to develop an apparatus for implementation of the process. Design criteria of the apparatus are defined and the techniques arc proposed to satisfy the design criterion. In order to examine the efficiency and applicability of the developed process, various three-dimensional shapes, such as a world-cup logo. a knob shape, an extruded cross, a twisted shape, a character, Son-o-kong. a helical gear shaped and a scissor shape are fabricated on the apparatus in which unit shape layer (USL) was generated to build up each layer.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.11
• /
• pp.546-555
• /
• 2001

ln this paper, the optimum design of electrical apparatus using design variable parametrization is presented. For analysis and design, the finite element method and the design sensitivity method is used, respectively. By applying the parametrization of the design variables, the obtained designed shape is continuous and smooth. For the parametrization the Bezier spline is used. The designed shape with parametrization is characterized by the control points. By delivering control points to the commercial CAD packages or NC machines, the exact designed shape can be realized in the manufacturing the electrical apparatus. The designed results with and without parametrization are compared and the validity of the parametrization is verified.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.760-765
• /
• 2001

A new rapid prototyping process, as a transfer type of Variable Lamination Manufacturing by using expandable polystyrene foam (VLM-ST), has been developed to reduce building time, apparatus cost including the introduction and the maintenance and additional post-processing. The objective of this study is to propose a VLM-ST process and to develop an apparatus for implementation of the process. Design criteria of the apparatus were defined and the techniques were proposed to satisfy the design criterion. In order to examine the efficiency and applicability of the developed process, various three-dimensional shapes, such as a world-cup logo, a knob shape and a character, Son-o-kong, were fabricated on the apparatus in which unit shape layer (USL) was generated to build up each layer.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.7
• /
• pp.587-594
• /
• 2016

The Split Hopkinson pressure bar (SHPB) test method, which is composed of three cylindrical bars, measuring devices and frames, is known for its reliable technique of acquiring the mechanical properties of specimens under a high strain rate. This paper demonstrates the processing of design and fabrication of SHPB. First of all, numerical analysis is applied in order to determine the design parameters of SHPB apparatus and verify the validity of design for a SHPB facility. Following this, SHPB apparatus were fabricated in accordance with acquired design parameters by simulation. In order to verify the validity of SHPB apparatus, experimental results using Al6061-T6 were compared with numerical data obtained from a corresponding simulation. The result of this comparative study demonstrates the applicability and validity of the fabricated apparatus.