• Electrical & Electronic Materials
• /
• v.9 no.9
• /
• pp.918-924
• /
• 1996

A downstream oxygen plasma is generated by capacitively coupled RF power and applied to photoresist stripping. Stripping rate (ashing rate) is measured in terms of RF power, chamber pressure, oxygen flow rate and temperature. Ashing reaction is thermally activated and depends on oxygen radical density. The ashing process is optimized to have the high ashing rate, good uniformity and minimal plasma damage using a statistical method.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.2
• /
• pp.35-38
• /
• 2008

This study shows the improvement of PR-Ashing rates in semi-conductor process using Atmospheric Plasma. Taguchi method is used to improve Ashing rates of photo-resist that is spread on the surface of a wafer. Improvement of Ashing rates is acquired through the decision of the effective factors and suitable combination of the factors. The results show the contribution rate of each factor and the effectiveness of Plasma for PR-Ashing process in this system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.195-195
• /
• 2010

본 연구에서 제작한 u-bolometer 은 적외선을 흡수하는 멤브레인이 a-Si 위에 Ti 메탈로 이루어져 있다. 이 u-bolometer 는 MEMS 센서로써 3차원 공진 구조를 제작하기 위해서는 희생층을 제거하는 공정이 필수적이며 이 희생 층으로 Polyimide를 사용하고 있는 공정에서 Plasma Ashing 공정은 더욱더 필수적이다. 이 Ashing 공정은 O2 플라즈마를 이용하며 이때 흡수물질인 Ti 레이어가 플라즈마에 의해 면저항과 흡수율의 특성이 어떻게 변화되는지 플라즈마 공정 전후를 분석한 결과 면저항의 변화가 나타났으며 uniformity도 높게 변화하였다. 또한 적외선 흡수율이 약 5% 차이가 나타나는 것을 확인 할 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.4
• /
• pp.325-331
• /
• 2007

In this study, the inter-metal dielectric material of FSG was changed by low-k material in $0.13{\mu}m$ foundry-compatible technology (FCT) device process based on fluorinated silicate glass (FSG). Black diamond (BD) was used as a low-k material with a dielectric constant of 2.95 for optimization and yield-improvement of the low-k based device process. For yield-improvement in low-k based device process, some problems such as photoresist (PR) poisoning, damage of low-k in etch/ash/cleaning process, and chemical mechanical planarization (CMP) delamination must be solved. The PR poisoning was not observed in BD based device. The pressure in CMP process decreased to 2.8 psi to remove the CMP delamination for Cu-CMP and USG-CMP. $H_2O$ ashing process was selected instead of $O_2$ ashing process due to the lowest condition of low-k damage. NE14 cleaning after ashing process lot the removal of organic residues in vias and trenches was employed for wet process instead of dilute HF (DHF) process. The similar-state of SRAM yield was obtained in Cu/low-k process compared with the conventional $0.13{\mu}m$ FCT device by the optimization of these process conditions.

• Korean Journal of Materials Research
• /
• v.20 no.10
• /
• pp.550-554
• /
• 2010

This work presents a fabrication procedure to make large-area, size-tunable, periodically different shape metal arrays using nanosphere lithography (NSL) combined with ashing and annealing. A polystyrene (PS, 580 ${\mu}m$) monolayer, which was used as a mask, was obtained with a mixed solution of PS in methanol by multi-step spin coating. The mask morphology was changed by oxygen RIE (Reactive Ion Etching) ashing and temperature processing by microwave heating. The Au or Pt deposition resulted in size tunable nano patterns with different morphologies such as hole and dots. These processes allow outstanding control of the size and morphology of the particles. Various sizes of hole patterns were obtained by reducing the size of the PS sphere through the ashing process, and by increasing the size of the PS sphere through annealing treatment, which resulted in tcontrolling the size of the metallic nanoparticles from 30 nm to 230 nm.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.7
• /
• pp.53-62
• /
• 2003

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.55-60
• /
• 2017

The supercritical $CO_2$ (sc-$CO_2$) mixture and the sc-$CO_2$-based Photoresist(PR) stripping(SCPS) process were applied to the removal of the post etch/ash PR residue on aluminum patterned wafers and the results were observed by scanning of electron microscope(SEM). In the case of MDII wafers, the carbonized PR was able to be effectively removed without pre-stripping by oxygen plasma ashing by using sc-$CO_2$ mixture containing the optimum formulated additives at the proper pressure and temperature, and the same result was also able to be obtained in the case of HDII wafer. It was found that the efficiency of SCPS of ion implanted wafer improved as the temperature of SCPS was high, so a very large amount of MEA in the sc-$CO_2$ mixture could be reduced if the temperature could be increased at condition that a process permits, and the ion implanted photoresist(IIP) on the wafer was able to be removed completely without pre-treatment of plasma ashing by using the only 1 step SCPS process. By using SCPS process, PR polymers formed on sidewalls of metal conductive layers such as aluminum films, titanium and titanium nitride films by dry etching and ashing processes were removed effectively with the minimization of the corrosion of the metal conductive layers.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.4
• /
• pp.204-209
• /
• 2006

Photo Resist (PR) ashing process was carried out with the atmospheric pressure- dielectric barrier discharge (ADBD) using $SF_6/N_2/O_2$. Ashing rate (AR) was sensitive to the mixing ratio of the oxygen and nitrogen of the blower type of ADBD asher. The maximum AR of 5000 A/min was achieved at 2% of oxygen in the $N_2$ plasma. With increasing the oxygen concentration to more than 2% in the $N_2$ plasma, the discharge becomes weak due to the high electron affinity of oxygen, resulting in the decrease of AR. When adding 0.5% of SF6 to $O_2/N_2$ mixed plasma, the PR AR increased drastically to 9000 A/min and the ashed surface of PR was smoother compared to the processed surface without $SF_6$. Carbon Fluorinated polymer may passivate the PR surface. It was also observed that the glass surface was not damaged by the fluorine.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.356-357
• /
• 2008

The effects of $O_2$ plasma ashing process for surface treatment of nano-wire Bio-FET were investigated. In order to evaluate the plasma damage introduced by $O_2$ plasma ashing, a back-gate biasing method was developed and the electrical characteristics as a function of $O_2$ plasma power were measured. Serious degradations of electrical characteristics of nano-wire Bio-FET were observed when the plasma power is higher than 50 W. For curing the plasma damages, a forming gas anneal (2 %, $H_2/N_2$) was carried out at $400^{\circ}C$. As a result, the electrical characteristics of nano-wire Bio-FET were considerably recovered.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.163-170
• /
• 2006

By removing sacrificial layer through ashing process, movable MEMS structure on substrate can be fabricated in surface micromachining. However, MEMS structure includes, during the ashing process, the warping or buckling effects due to stress gradient along the vertical direction of thin film. In this study, we presented method for counteracting the unwanted deflection of MEMS structure and designed using character of deposit process to overcome limited design conditions. Unit cell patterns were designed with character of deposit shape, and their final shapes were adopted using Finite Element Method. Finally, RF MEMS switch was fabricated by surface micro machining as test vehicles. We checked out that alleviation effect for deformation of switch improved by 35%.