• 한국결정성장학회지
• /
• 제28권2호
• /
• pp.63-68
• /
• 2018

Natural convection of a two dimensional laminar steady-state incompressible fluid flow in a rectangular enclosure has been investigated numerically for low aspect ratios with the physical vapor transport crystal growth. Results show that for aspect ratio (Ar = L/H) range of $0.1{\leq}Ar{\leq}1.5$, with the increase in Grashof number by one order of magnitude, the total mass flux is much augmented, and is exponentially decayed with the aspect ratio. Velocity and temperature profiles are presented at the mid-width of the rectangular enclosure. It is found that the effect of Grashof number on mass transfer is less significant when the enclosure is shallow (Ar = 0.1) and the influence of aspect ratio is stranger when the enclosure is tall and the Grashof number is high. Therefore, the convective phenomena are greatly affected by the variation of aspect ratios.

• Advances in concrete construction
• /
• 제2권3호
• /
• pp.177-192
• /
• 2014

One of the main applications of FRP composites is confining concrete columns. Hence identifying the cyclic and monotonic stress-strain behavior of confined concrete columns and the parameters influencing this behavior is inevitable. Two significant parameters affecting the stress-strain behavior are aspect ratio and corner radius. The present study aims to scrutinize the effects of corner radius and aspect ratio on different aspects of stress-strain behavior of FRP confined concrete specimens (rectangular, square and circular). Hence 44 FRP confined concrete specimens were tested and the results of the tests were investigated. The findings indicated that for specimens with different aspect ratios, the relationship between the ultimate stress and the corner radius is linear and the variations of the ultimate stress versus the corner radius decreases as a result of an increase in aspect ratio. It was also observed that increase of the corner radius results in increase of the compressive strength and ultimate axial strain and increase of the aspect ratio causes an increase of the ultimate axial strain but a decrease of the compressive strength. Investigation of the ultimate condition showed that the FRP hoop rupture strain is smaller in comparison with the one obtained from the tensile coupon test and also the ultimate axial strain and confined concrete strength are smaller when a prism is under monotonic loading. Other important results of this study were, an increase in the axial strain during the early stage of unloading paths and increase of the confining effect of FRP jacket with the increase and decrease of the corner radius and aspect ratio respectively, a decrease in the slope of reloading branches with cycle repetitions and the independence of this trend from the variations of the aspect ratio and corner radius and also quadric relationship between the number of each cycle and the plastic strain of the same cycle as well as the independence of this relationship from the aspect ratio and corner radius.

• 한국농공학회논문집
• /
• 제48권3호
• /
• pp.85-94
• /
• 2006

Practially useful method of steel fiber for construction work is presented in this study. The most important purpose of this study is to develop a model which can predict mechanical behavior of the structure according to aspect ratio and volume fraction of steel fiber. Experiments on compressive strength, elastic modulus, and splitting strength were performed with self-made cylindrical specimens of variable aspect ratios and volume fractions. The experiment showed that compressive strength was not in direct proportion to volume fraction which doesn't seem to have great influence over compressive strength. However, splitting strength showed almost direct proportion to aspect ratio and volume fraction. Improvement of optimal efficiency was confirmed when the aspect ratio was 70. Experiments on flexural strength, fracture energy, and characteristic length were carried out with self-manufactured beams with notch. As a result, increases of flexural strength, fracture energy, and characteristic length according to increase of volume fraction tend to be prominent when aspect ratio is 70. The steel fiber improves concrete to be more ductile and tough. Moreover, regression analysis was the performed and predictable model was developed after determining variables. With comparison and analysis of suggested estimated values and measured data, reliance of the model was verified.

• 한국도로학회논문집
• /
• 제20권3호
• /
• pp.19-26
• /
• 2018

PURPOSES : The main purpose of this study is suggest of field bond strength evaluation method for more objective evaluation method through Evaluation of Bond Strength Properties with changing aspect ratio and temperature. METHODS : The evaluation is laboratory bond strength test. Using the core machine, the pull-off test method ; the bond strength test of interface layer the universal testing machine. RESULTS : As a result of the laboratory bond strength evaluation, it was verified that the bond strength by aspect ratio decreases linearly with increasing aspect ratio and the bond strength properties by temperature change existed at high and low temperature condition relative to odinary temperature condition. CONCLUSIONS : According to the results of laboratory bond strength evaluation, the field bond strength evaluation results suggest applying the proposed correction factor (0.8, 1.0, 1.4, 1.9) according to aspect ratio(0.5, 0.1, 1.5, 2.0), For more objective evaluation of the bond strength, it is analyzed that the evaluation value is within $6{\sim}32^{\circ}C$ and the result can be obtained within 5% of the coefficient of variation.

• 대한조선학회지
• /
• 제21권1호
• /
• pp.21-34
• /
• 1984

This paper is concerned with the experimental investigation of transverse vibration characteristics in water of rectangular plates having an inner free cutout. Systematic experiments are carried out to investigate effects of the surrounding water on the added mass and the natural frequency of the plates due to the changes of the aspect ratio, hole size and eccentricity. The main subject is the clamped rectangular plate with a circular hole. For the purpose of comparative evaluations, some other common-type boundary conditions and hole shapes such as ellipses and rectangles are also investigated. Some of the results obtain are as follows; 1) For each given aspect ratio of the plate, there is a hole area ratio which gives a minimum value of the nondimensional frequency parameter for each mode. The hole area ratio increases as the order number of the mode increases. 2) The nondimensinal mass-increment parameter decreases as the aspect ration or the order number of the mode increases. For each given aspect ratio, the parameter the fundamental mode decreases monotonically as the hole area ratio increase. In cases of the second and higher order modes, however, each mode has a hole area ratio which gives a maximum value of the parameter for each aspect ratio more then 2/3. 3) Comparing elliptic holes with rectangular ones with same hole area ratio, nondimensional frequency parameters are almost same for each given ratio of the shorter axises to the longer one. 4) The influences of difference in boundary condion on nondimensional frequency parameters in water are similar to those in air.

• 터널과지하공간
• /
• 제23권2호
• /
• pp.150-159
• /
• 2013

일반적으로 열저장소의 종횡비(폭에 대한 높이의 비)가 커짐에 따라 저장된 열에너지의 성층화가 높게 유지될 수 있는 것으로 알려져 있다. 따라서 열저장소의 열적 성능을 높이기 위해서는 저장소 종횡비를 크게 설정하는 것이 유리할 것이다. 그러나 종횡비의 증가에 따라 저장소의 폭에 비해 높이가 커지고, 이는 열저장소의 구조적 안정성 측면에서 불리하게 작용할 수 있으므로 저장소의 최적 종횡비 결정시 열적 성능 분석과 더불어 역학적 안정성에 대한 정량적인 분석이 수행되어야 할 것이다. 본 연구에서는 지하 열에너지 저장을 위한 사일로형 암반공동의 종횡비 변화에 따른 역학적 안정성을 수치해석적으로 조사하였다. 적용한 종횡비는 1-6의 범위이었고, 전단강도 감소기법에 의한 안전율을 토대로 암반공동의 역학적 안정성을 평가하였다. 종횡비별 안정성 분석 결과, 암반공동의 종횡비가 증가함에 따라 안전율이 감소하는 경향을 보였으며, 주변 암반의 측압계수가 안정성에 미치는 영향이 큰 것으로 분석되었다. 또한 동일한 암반특성 및 종횡비 조건에서 암반공동의 규모(저장 용량)가 줄어듦에 따라 안정성이 향상되는 것으로 나타나, 큰 규모의 단일 암반공동을 소규모의 다중 암반공동으로 분할함으로써 높은 종횡비의 암반공동 설계가 가능한 것을 알 수 있었다.

• Journal of Welding and Joining
• /
• 제33권5호
• /
• pp.47-52
• /
• 2015

In this study, it was tried to analyze the effects of welding parameters on the weld penetration and aspect ratio when a STS316L pipe was welded in a horizontal position by GTAW. Experiments were systematically designed using a L18 orthogonal array, and the effects of welding parameters were statistically analyzed by ANOVA(Analysis of Variance). The shielding gas type has the largest effect on both the penetration and aspect ratio. The welding current type and shielding gas flow rate have a little effect on the penetration, whereas the electrode tip angle has a little effect on the aspect ratio. When welded at a selected welding condition, which is composed of He shielding gas, pulse current of 300/45 A, electrode tip angle of 90o, and shielding gas flow rate of 30 l/min, the estimated interval at least 95 % confidence was $1.99{\pm}0.18mm$ for the penetration and $0.31{\pm}0.04$ for the aspect ratio. From the confirmation experiments, the average penetration and aspect ratio were well agreed with the estimation as 1.96 mm and 0.30, respectively. Additionally, the effects of the welding speed and welding current on the penetration and aspect ratio were experimented and analyzed by linear regression. The penetration was linearly increased with the decrease of the welding speed and with the increase of the welding current, but the aspect ratio showed a tendency to a little decrease with the increase of both the welding speed and current.

• 한국전자통신학회논문지
• /
• 제15권2호
• /
• pp.349-356
• /
• 2020

본 논문은 교통사고 방지를 위한 운전자의 눈 영상비를 이용한 상태 경고시스템의 설계에 대해 소개하고 있다. 제안하는 운전자 상태 경고 시스템은 눈 인식을 위한 카메라, 카메라를 통해 들어오는 정보를 처리하는 라즈베리파이, 그리고 그 정보를 통해 운전자에게 경고를 줄 때 필요한 부저와 진동기로 구성되어 있다. 운전자의 눈을 인식하기 위해서 기울기 방향성 히스토그램 기술과 딥러닝 기반의 얼굴 표지점 추정 기법을 사용하였다. 동작을 시작하면, 시스템은 눈 주변의 6개의 좌표를 통해 눈 영상비를 계산한다. 그리고 눈을 뜬 상태와 감은 상태의 눈 영상비를 각각 계산한 후 이 두 값으로부터 눈의 상태를 판단하는데 사용하는 문턱 값을 설정한다. 문턱 값이 운전자의 눈 크기에 적응하면서 설정되기 때문에 시스템은 최적의 문턱 값을 사용하여 운전자의 상태를 판단할 수 있다. 또한 낮은 조도에서도 눈을 인식할 수 있도록 회색조 변환 이미지와 LAB모델 이미지를 합성하여 사용하였다.

• 한국건설순환자원학회논문집
• /
• 제6권3호
• /
• pp.160-166
• /
• 2018

이 연구의 목적은 폴리에틸렌 섬유의 형상비에 따른 알칼리활성 무시멘트 복합재료의 압축강도와 인장거동을 실험적으로 조사하는 것이다. 이를 위하여 섬유의 형상비에 따라 두 가지 배합을 결정하였고, 압축강도를 측정하고 인장실험을 수행하였다. 실험결과 섬유의 형상비에 따른 압축강도의 영향은 거의 나타나지 않은 반면 인장거동은 큰 차이가 발생하였다. 형상비가 높은 섬유를 사용한 배합은 형상비가 낮은 섬유를 사용한 배합에 비하여 강도, 변형성능, 균열개수가 크게 나타났다. 반면에 균열간격과 균열폭은 높은 형상비를 갖는 섬유를 함유한 배합에서 작게 나타났다.

• 산업기술연구
• /
• 제19권
• /
• pp.59-65
• /
• 1999

This study is to analyze turbulent flow over a backward-facing step in a rectangular duct. The side wall effects on the internal flow were determined by varying the aspect ratio(defined as the step span-to-height ratio) from 1 to 20. In the flow behind a backward-facing step, separation, recirculation and redeveloping is occurred frequently. These phenomena appear in a particular variation by varying the aspect ratio. The results show that the aspect ratio has an influence on the velocity and reattachment length. When the AR is increased, the reattachment length is increased. For 6 over aspect ration, the rate of increase is decreased. The length of recirculation in the upper corner is increased, as the increase of aspect ration. It's width is not changed in the variation of aspect ration. The transverse, streamwise and spanwise velocities were decreased along the flow down stream of the step.