• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.2
• /
• pp.304-310
• /
• 2001

This paper describes the analysis of flow field using a projection finite element method. The projection scheme with a pressure correction is presented for the analysis of an incompressible Navier-Stokes flow. The projection scheme is analyzed numerically and applied to the well-known bench marking problems such as lid driven cavity. Finally, the projection scheme is applied to a flow through the automobiles front. In the automobiles cooling system, the flow through its front is very important to a cooling performance. The results show that the flow quantity increases by locating the position of bumper to the further front position of a car. And, the improvement on the suction part below a bumper achieves the more passing flow quantity. The attachment of an air dam increases passing flow quantity causing the pressure rise to the front part and the pressure drop beneath a car.

• Journal of the Korean Society of Industry Convergence
• /
• v.9 no.1
• /
• pp.67-72
• /
• 2006

This study is on the development of algorithm of surge test for quality control on electrical parts of throttle body in automobiles with internal combustion engine, not only to know its condition to be good or not, but also jugding its condition to be classified into six types. To know whether its condition to be good or not, comparing and analyzing between two waveforms generated from master and test coil of throttle body. If test net area is below 20% of master area, the condition of test coil is good. By analyzing test coil waveform to master coil waveform, the condition of test coil into winding badness, insulation badness, layer and corona discharge, short badness should known. Therefore quality control system on electrical parts of throttle body should be developed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.222-227
• /
• 1998

Collision warning systems have been an active research and development area as the interests and demands for ASV's (Advanced Safety Vehicles) have increased. This paper presents an experimental investigation of a collision warning system for automobiles. A collision warning HiLS(Hardware-in-the-Loop Simulation) system has been designed and used to test the collision warning algorithm, radar sensors, and warning displays under realistic operating conditions in the laboratory. the collision warning algorithm is operated by a warning index, which is a function of the warning distance and the braking distance. The computer calculates velocities of the preceding vehicle and following vehicle, relative distance and relative velocity of the vehicles using vehicle simulation models. The relative distance and the relative velocity are applied to the vehicle simulator controlled by a DC motor.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.240-246
• /
• 2000

One of the widely accepted methods for evaluating the interior sound quality of automobiles is Articulation Index(AI). The AI actually measures the articulation level of the sound in the vehicle cabin as passengers talk to one another. In this study, the effect of two different absorption materials inside the cabin on AI has been investigated by ray-tracing method : one is firewall, the other is celling. It turns out that the back seat location is found to be strongly dependent on the type of absorption materials treated at the celling, since the sound absorbing area is different due to the location and the firewall is situated in the "Reverberation Radius". The proposed methdo could be used to improve the sound quality of automobiles at the design stge.sign stge.

• Journal of the Korean Society of Safety
• /
• v.23 no.1
• /
• pp.18-23
• /
• 2008

The abnormal wears such as unfair-wear and early-wear happen in the earn shaft surface of automobiles. These abnormal wears make efficiency of engines decrease and threaten safety of automobiles. The wear characteristics of the cam shaft is very important for the automobile safety. The cam shaft is surface-hardened by the high frequency induction. In this study, we investigated the wear characteristics of the hardened surface with a SM53C steel. The wear characteristics is examined according to the hardened depth and the amount of load.

• International Journal of Automotive Technology
• /
• v.5 no.2
• /
• pp.69-76
• /
• 2004

This paper evaluates the effectiveness of four-wheel-steering system from the viewpoint of lane-keeping control theory. In this paper, the lane-keeping control system is designed on the basis of the four-wheel-steering automobiles whose desired steering response is realized with the application of model matching control. Two types of desired steering responses are presented in this paper. One is zero-sideslip response, the other one is steering response which realizes zero-phase-delay of lateral acceleration. Using simplified linear two degree-of-freedom bicycle model, simulation study and theoretical analysis are conducted to evaluate the lane-keeping control performance of active four-wheel-steering automobiles which have different desired steering responses. Finally, the evaluation is conducted on straight and curved roadway tracking maneuvers.

• Journal of computational fluids engineering
• /
• v.18 no.2
• /
• pp.26-34
• /
• 2013

In modern days, automobiles are the most important means of transportation. With the development of automobiles, noises generated during operation has been recognized as a significant factor of performance to provide drivers with better driving environment along with other passengers. In this study, drone noise(pulsating noise), generated at the rear window when its opened, is predicted to understand the physics of its phenomenon at various velocities. The compressible Navier-stokes equation will be used with $6^{th}$ order compact finite difference scheme to analyze the characteristics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.630-634
• /
• 1997

In this paper,we will discuss in the forming process design of the making engine pulleys for automobiles. These pulleys are required to be made by precision deep drawing process because these are to be combined with bearings and engine timing belts. These pulleys are used of cold rolled steel plates starting with the initial blanking size of 115.2mm and the initial thickness of 1.2mm. Our deep drawing process is designed the continuous 5-steps process, that is, 1'st deep drawing, 2'nd reverse redrawing, 3'rd trimming, 4'th drawing-ironing and 5'yh piercing. This process need no in-process annealing.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1474-1486
• /
• 1990

The frictional characteristics of galvanized sheet steels(GA, EG, EGF, EGN) for automobiles were studied and compared with that of cold rolled sheet steel. A draw bead tester which simulates metal flow through a draw bead in stamping die face was used to measure coefficients of friction of galvanized sheet steels for four kinds of lubricants. Stamping formability of galvanized sheet steels for quarter outer panel was examined. The results show that stamping formability and friction characteristics were mainly influenced by the nature of zinc coating, surface roughness and micro hardness of coated layer, and proved to be very sensitive to the lubricant used.

• Journal of Power System Engineering
• /
• v.10 no.2
• /
• pp.68-74
• /
• 2006

In the development of new automobiles, the efforts to reduce environmental problems like air pollution have been risen. Blowby gas consists of about $20{\sim}35%$ of total amount of Hydrocarbon (HC), one of dangerous pollutants issuing from automobiles. A PCV valve is a very small component in an automotive engine but it is a very important part. Because that a PCV valve is used to control blowby gas and to recirculate it into a manifold automatically. Although it has very simple operating principle, designing a PCV valve is so difficult due to interaction between fluid and solid. In this study, our purpose is to develop a design program for a PCV valve and to verify its efficiency. Both Bernoulli equation and 4th order Runge-Kutta method were adopted to predict spool displacements and flow patterns. Comparing with experiments, it was found that both spool diameters and displacements were predicted well, however, flow rates showed a little differences because of the assumption of non viscous flow.