• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.8
• /
• pp.1085-1091
• /
• 2014

A model based SOC estimation scheme using parameter identification is described and applied to a Lithium-ion battery module that can be installed in electric vehicles. Simulation studies are performed to verify the effect of sensor faults on the SOC estimation results for terminal voltage sensor and load current sensor. The sensor faults should be detected and isolated as soon as possible because the SOC estimation error due to any sensor fault seriously affects the overall performance of the BMS. A new fault detection and isolation(FDI) scheme by which the fault of terminal voltage sensor and load current sensor can be detected and isolated is proposed to improve the reliability of the BMS. The proposed FDI scheme utilizes the parameter estimation of an input-output model and two fuzzy predictors for residual generation; one for terminal voltage and the other for load current. Recently developed dual polarization(DP) model is taken to develope and evaluate the performance of the proposed FDI scheme. Simulation results show the practical feasibility of the proposed FDI scheme.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.929-938
• /
• 2015

Maximum power point tracking (MPPT) and battery charging control are two important functions for a solar battery charger. The former improves utilization of the available solar energy, while the latter ensures a prolonged battery life. Nevertheless, complete implementation of both functions can be complex and costly, especially for low voltage application such as standalone street lamps. In this paper, the operation of a solar battery charger for standalone street light systems is investigated. Using only one voltage sensor, the solar charger is able to operate in both MPPT and constant voltage (CV) charging mode, hence providing high performance at a low cost. Using a lab prototype and a solar simulator, the operation of the charger system is demonstrated and its performance under varying irradiance is validated.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.9
• /
• pp.55-63
• /
• 2014

Up to date, numerous studies on wireless sensor networks have been performed to overcome the Energy-Constraint of the sensor system. Existing schemes for estimating the residual energy have considered only voltage of sensor system. However battery performance in the real is affected by temperature and load. In this paper we introduce more accurate scheme, for the use in wireless sensor node, based on the interpolation of lookup tables which allow for temperature and load characteristics, as well as battery voltage.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.465-466
• /
• 2008

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.12
• /
• pp.74-83
• /
• 2014

This paper proposes a study on the configuration of balancing of plant(BOP) and implementation of battery management system(BMS) functions for vanadium redox flow battery(VRFB) and propose a method consists of sensor and required design specifications BOP system configuration. And it proposes an method of the functions implementation and control algorithm of the BMS for flow battery. Functions of BMS include temperature control, the charge and discharge control, flow control, level control, state of charge(SOC) estimation and a battery protection through the sensor signal of BOP. Functions of BMS is implemented by the sensor signal, so it is recognized as a very important factor measurement accuracy of the data. Therefore, measuring a mechanical signal(flow rate, temperature, level) through the BOP test model, and the measuring an electrical signal(cell voltage, stack voltage and stack current) through the VRFB charge-discharge system and analyzes the precision of data in this paper. Also it shows a good charge-discharge test results by the SOC estimation algorithm of VRFB. Proposed BOP configuration and BMS functions implementation can be used as a reference indicator for VRFB system design.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05a
• /
• pp.454-457
• /
• 2011

논문에서는 EEM 시뮬레이터를 개발하여 개발되어진 시뮬레이터를 Voltage, Current, Resistance의 데이터를 추출하고 실차를 이용하여 시동 테스트를 통한 자동차 시동시 순간적으로 흐르는 Voltage, Current, Resistance의 순간 변화량을 추출하여 과 각각의 특성을 비교하여 Battery의 SOC, SOH를 구하고 자동차의 Battery 를 획기적으로 관리할 수 있는 시뮬레이터를 개발하려 한다.

• Journal of Aerospace System Engineering
• /
• v.14 no.6
• /
• pp.79-84
• /
• 2020

Cooler driver electronics (CDE) for maintaining low temperature of the satellite payload IR sensor consists of a compressor that has a pulsation current load condition when it is operated. This pulsation current produces large voltage fluctuation, which affects both load and regulated bus stability. Thus, CDE power conditioning system consists of a primary bus, infrared power distribution unit for battery charging and protection, reverse current protection diode, and battery, which is used as a buffer. In this study, the operational mode analysis is performed by each part with equivalent impedance modeling verified through system level simulation. From this mode analysis, the safety margin for state of charge and open circuit voltage of the battery is determined for satisfying the minimum operational voltage of the CDE load.

• Smart Structures and Systems
• /
• v.29 no.5
• /
• pp.661-675
• /
• 2022

In this paper, an electric vehicle drives with efficient control and low cost hardware using four quadrant DC converter with Permanent Magnet Direct Current (PMDC) motor fed by DC boost converter is presented. The main idea of this work is to improve the energy efficiency of the conversion chain of an electric vehicle by inserting a boost converter between the battery and the four quadrant-DC motor chopper assembly. Consequently, this method makes it possible to maintain the amplification gain of the 4 quadrant chopper constant regardless of the battery voltage drop and even in the presence of a fault in the battery. One of the most important control problems is control under heavy uncertainty conditions. The higher order sliding mode control technique is introduced for the adjustment of DC bus voltage and mechanical motor speed. To implement the proposed approach in the automotive field, experimental tests were carried out. The performances obtained show the usefulness of this system for a better energy management of an electric vehicle and an ideal control under different operating conditions and constraints, mostly at nominal operation, in the presence of a load torque, when reversing the direction of rotation of the motor speed and even in case of battery chamber failure. The whole system has been tested experimentally and its performance has been analyzed.

• Journal of Korea Society of Industrial Information Systems
• /
• v.16 no.1
• /
• pp.31-36
• /
• 2011

Ubiquitous network and wireless sensor networks is being applied in various fields. Located at target areas, node of wireless sensor network uses batteries as a power source. Batteries have a limited energy in sensor network applications. Also, before use, the battery must be charged and It is difficult to replace the battery. Therefore, energy harvesting technology is being researched and being developed for long life of sensor node. Especially, sola energy is being extensively researched. because that can have great amounts of energy than other environmental energy in a short time. In this study, we tested battery charging and recharging, operation of sensor node using Solar Cell. Also, monitoring data gathering and voltage Analysis showed energy harvesting time of Sola Cell battery for sensor node and operation of sensor node.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05b
• /
• pp.753-756
• /
• 2011

지속적인 충/방전에 의하여 표준 수명 보다 더 빠른 노화 현상을 일으키는 배터리의 효율적인 관리를 위하여, 배터리의 내부 상태를 모니터링 하였다. 정확한 배터리 모니터링을 위해서 해당하는 배터리의 잔존 용량 및 잔존 수명을 정확히 예측할 수 있어야 하며, 이를 위해 Open Voltage를 사용한 실험, 에너지 보존 법칙에 의한 충전 전류 측정법, 시동 시 최대 전류와 내부 저항의 변화량을 알아내는 실험을 하였다. Open Voltage 실험 결과, SOC수치에 따른 특정 전압의 범위를 알 수 있었고, 이 전압은 온도에 의해 변동된다는 것을 확인할 수 있었다. 충전 그래프를 그려본 결과 충전횟수와 완충에 걸리는 시간은 반비례하며, 배터리 내부에 충전되는 총 전류의 양과도 관계가 있었다. 시동 실험에서는 최저 전압 드롭 값과 최대 공급 전류의 범위를 알 수 있었으며, 특정 SOC 구간 내 내부 저항의 값을 차이를 알 수 있었다. 이 값들은 각 SOC의 수치에 비례한 결과를 보였다. 이 결과들을 정리하여, 배터리 내부 상태를 예측하는 방법을 제안하고자 한다.