• Journal of computational fluids engineering
• /
• v.20 no.4
• /
• pp.44-50
• /
• 2015

The computational efficiency of flow simulations with Multi-resolution analysis (MRA) was enhanced via the boundary treatment of the computational domain. In MRA, an adaptive dataset to a solution is constructed through data decomposition with interpolating polynomial and thresholding. During the decomposition process, the basis points of interpolation should exceed the boundary of the computational domain. In order to resolve this problem, the weight coefficients of interpolating polynomial were adjusted near the boundaries. By this boundary treatment, the computational efficiency of MRA was enhanced while the numerical accuracy of a solution was unchanged. This modified MRA was applied to two-dimensional steady Euler equations and the enhancement of computational efficiency and the maintenance of numerical accuracy were assessed.

• The Journal of the Korea Contents Association
• /
• v.13 no.2
• /
• pp.505-511
• /
• 2013

A new boundary treatment technique which can be applied to axi-symmetric topography with inclined bottom was developed. Although the finite element method is good for complex geometry, there is no proper boundary treatment when a boundary is not a vertical section because the water depth at the coastline becomes zero. In this study, we developed a new boundary treatment for inclined bottom using the analytical solution for long wave. To develope a model, the mild-slope equation was used and then, a computational domain is divided into an analytical region and a numerical region. By combining a numerical and an analytical solutions, a complete solution was obtained. The developed solution was validated by comparing with a previous analytical solution.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.6
• /
• pp.650-655
• /
• 2011

Analysis of two-dimensional Rayleigh wave scattering pattern by a surface defect is studied through modified boundary element method. BEM proposed in this paper has special treatment at each end of boundary which should have the Rayleigh wave go away without any generation of virtual reflections. It is shown that treatment for truncated boundary which is used to model two-dimensional Rayleigh waves' behavior in an elastic half-space is successfully implemented. To check numerical results' accuracy, time domain IFFT signal of the displacements is presented. Improvement on getting rid of unwanted influence of truncated boundary induced by 2-D Rayleigh waves on a flat surface of an elastic half-infinite medium is shown. As a final goal, the numerical results of Rayleigh wave scattering trend are plotted and they are compared with theoretical curves to prove its accuracy.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.250-254
• /
• 2002

Intergranular corrosion of austenitic stainless steels is a conventional and momentous problem during welding and high temperature use. One of the major reasons for such intergranular corrosion is so-called sensitization, i.e., chromium depletion due to chromium carbide precipitation at grain boundaries. Conventional methods for preventing sensitization of austenitic stainless steels include reduction of carbon content in the material, stabilization of carbon atoms as non-chromium carbides by the addition of titanium, niobium or zirconium, local solution-heat-treatment by laser beam, etc. These methods, however, are not without drawbacks. Recent grain boundary structure studies have demonstrated that grain boundary phenomena strongly depend on the crystallographic nature and atomic structure of the grain boundary, and that grain boundaries with coincidence site lattices are immune to intergranular corrosion. The concept of "grain boundary design and control", which involves a desirable grain boundary character distribution, has been developed as grain boundary engineering. The feasibility of grain boundary engineering has been demonstrated mainly by thermomechanical treatments. In the present study, a thermomechanical treatment was tried to improve the resistance to the sensitization by grain boundary engineering. A type 304 austenitic stainless steel was pre-strained and heat-treated, and then sensitized, varying the parameters (pre-strain, temperature, time, etc.) during the thermomechanical treatment. The grain boundary character distribution was examined by orientation imaging microscopy. The intergranular corrosion resistance was evaluated by electrochemical potentiokinetic reactivation and ferric sulfate-sulfuric acid tests. The sensitivity to intergranular corrosion was reduced by the thermomechanical treatment and indicated a minimum at a small roll-reduction. The frequency of coincidence-site-lattice boundaries indicated a maximum at a small strain. The ferric sulfate-sulfuric acid test showed much smaller corrosion rate in the thermomechanically-treated specimen than in the base material. An excellent intergranular corrosion resistance was obtained by a small strain annealing at a relatively low temperature for long time. The optimum parameters created a uniform distribution of a high frequency of coincidence site lattice boundaries in the specimen where corrosive random boundaries were isolated. The results suggest that the thermomechanical treatment can introduce low energy segments in the grain boundary network by annealing twins and can arrest the percolation of intergranular corrosion from the surface.

• Journal of computational fluids engineering
• /
• v.19 no.3
• /
• pp.77-84
• /
• 2014

The lattice Boltzmann (LB) method has been used to simulate rarefied gas flows in a micro-system as an alternative tool. However, previous results were mainly focused on a simple geometry with flat walls because the LB method is modeled on uniform Cartesian lattices. When previous boundary conditions for the microflows are applied to curved walls, the use of them requires approximation of the curved boundary by a series of stair steps, and introduces additional errors. For macroflows, no-slip curved wall boundary treatments have been developed remarkably in order to overcome these limits. However, the investigations for the slip curved wall boundary have rarely been performed for microflows. In this work, a curved boundary treatment of the LB method for a slip flow has been introduced. The results of the LB method for 2D microchannel and 3D microtube flows are in excellent agreement with the analytical solutions.

• Selected Papers of The Society of Naval Architects of Korea
• /
• v.2 no.1
• /
• pp.63-78
• /
• 1994

This paper deals with the treatment of the open boundary in two-dimensional free-surface wave problems. Two numerical schemes are investigated for the implementation of the open boundary condition. One is to add the artificial damping term to the dynamic free-surface boundary condition, in which the determination of suitable damping coefficient and the damping zone is the most important. The other is a modified Orlanski's method, which is known to be very useful for the uni-directional waves. Using these two schemes, numerical tests have been conducted for a few typical free-surface wave problems. To obtain the numerical solution of the free-surface boundary value problem, the fundamental source-distribution method is used and the fully nonlinear free-surface boundary conditions are applied. The computed results are presented in comparison with those of others for the proof of practicality of these two schemes.

• Communications of the Korean Mathematical Society
• /
• v.12 no.2
• /
• pp.427-456
• /
• 1997

This paper concerns constructing wavelet bases on the unit interval, where a new boundary treatment is provided to overcome certain drawbacks of eariler constructions. Wavelet expansions on the unit interval usually suffer from artificial boundary effects and poor convergence at the boundaries. Many researchers have suggested a solution to the drawbacks. From a practical point of view, their solutions also have a common disadvantage. This paper provides a new solution using biorthogonality near the boundaries, that avoids the disadvantage while preserving their advantages.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.3 no.3
• /
• pp.176-183
• /
• 1991

In this paper. boundary element method is applied to the analysis of nonlinear free surface wave. A particular concern is given to the treatment of the open boundaries at the in-flow boundary and out-flow boundary, which uses the mass-flux and energy-flux considering the continuity of fluid. By assuming the fluid to be inviscid and incompressible and the flow to be irrotational. the problem is formulated mathematically as a two-dimentional nonlinear problem in terms of a velocity potential. The equation(Laplace equation) and the boundary conditions are transformed into two boundary integral equations. Due to the nonlinearity of the problem. the incremental method is used for the numerical analysis. Numerical results obtained by the present boundary element method are compared with those obtained by the finite element method and also with experimental values.

• Structural Engineering and Mechanics
• /
• v.78 no.4
• /
• pp.497-518
• /
• 2021

In this study, a new method for treating the wall boundary in smoothed particle hydrodynamics (SPH) is proposed to simulate free surface flows effectively. Unlike conventional methods of wall boundary treatment through boundary particles, in the proposed method, the wall boundary condition is directly imposed by adding boundary truncation terms to the mass and momentum conservation equations. Thus, boundary particles are not used in boundary modeling. Doing so, the wall boundary condition is accurately imposed, boundary modeling is simplified, and computation is made efficient without losing stability in SPH. Performance of the proposed method is demonstrated through several numerical examples: dam break, dam break with a wedge, sloshing, inclined bed, cross-lever rotation, pulsating tank and sloshing with a flexible baffle. These results are compared with available experimental results, analytical solutions, and results obtained using the boundary particle method.

• Journal of computational fluids engineering
• /
• v.11 no.3 s.34
• /
• pp.28-36
• /
• 2006

NSBT(No Slip Boundary Treatment) is a newly developed scheme for the treatment of a no slip condition on the solid wall of obstacle in a flow field. In our research, NSBT was used to perform LBM simulation of a flow over a circular cylinder to determine the flow feature and aerodynamics characteristic of the cylinder. To ascertain the applicability of NSBT on the complex shape of the obstacle, it was first simulated for the case of the flow over a circular and square cylinder in a channel and the results were compared against the solution of Navier-Stokes equation. The simulations were performed in a moderate range of Reynolds number at each cylinder position to identify the flow feature and aerodynamic characteristics of circular cylinder in a channel. The drag coefficients of the cylinder were calculated from the simulation results. We have numerically confirmed that the critical reynolds number for vortex shedding is in the range of 200$\sim$250. For the gap parameter $\gamma$ = 2 cases at Re > 240, the vortex shedding were symmetric and it resembled the Karmann vortex. As the cylinder approached to one wall, the vorticity significantly reduced in length while the vorticity on the other side elongated and the vorticity combined with the wall boundary-layer vorticity. The resultant $C_d$ by LBM concurred with the results of DNS simulation performed by previous researchers.