• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.341-348
• /
• 2002

For the light guide plate of the TFT-LCD, there have been increasing demands for higher brightness, thin and light-weight design, and lower power consumption. To meet these demands, a micro-prism-type frontlight that integrates a prismatic sheet and a light-guiding plate has been developed. In this paper, the influences of processing conditions on the brightness were studied lot the injection molding of the light guide plate. Based on the experiment with an actual mold, the design of experiments and the neural network theory were used lot choosing the optimal processing parameters to increase the brightness and the uniformity. The verification experiment also showed that the brightness and the uniformity were increased dramatically with the chosen processing conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.9
• /
• pp.38-44
• /
• 2008

Light guide plate is one of most important components which are composed of back light unit, affecting the quality and performance of LCD. Average brightness and uniformity are especially key factors for designing the light guide unit. These qualities are affected and controlled by the pattern being attached to the back of light guide unit. In order to obtain high brightness and uniformity the optimized pattern design is adopted for LGP. In this study, optimized molding condition for LGP with 0.4 mm thickness was obtained by using the Moldflow simulation software and the optimized pattern for better brightness uniformity was designed for the thickness of the 0.4 mm by trial and error method. The brightness was measured for the different LGP thicknesses and the residual stress analysis was performed for 0.4 mmthickness by the photoelasticity and the results are compared with 0.5 mm, 0.6 mm thickness.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1609-1612
• /
• 2005

The effects of injection molding conditions on the uniformity and brightness of light guide plate(LGP) with micro-patterns were investigated in the present study. An injection molding system for stampers with mirco-pattern was designed and manufactured to perform experiment. Variations of injection molding speed, mold and melt temperature for LGP were considered in this work. Also, injection molding characteristics of LGP were investigated by numerical analysis using plastic injection molding commercial code. It was shown that injection molding conditions such as injection speed, melt temperature and mold temperature can have an effect on the uniformity and brightness of light guide plate.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.4 s.334
• /
• pp.53-60
• /
• 2005

This work Proposes and describes an LCD backlight driver IC using a voltage feedback circuit which improves the brightness uniformity. The proposed circuit controls the brightness of a backlight by amplifying of sampling voltage at a lamp. To keep the uniformity of brightness, the circuit has a reference lamp. The output voltage of the reference lamp is supplied commonly to each lamp that reduces a resistance deviation of the lamps. As a result, the proposed circuit shows brightness uniformity improvement of about $40\%$ compared to the conventional ones.

• Journal of Korea Multimedia Society
• /
• v.12 no.7
• /
• pp.1016-1021
• /
• 2009

Among many factors for evaluating the performance of color printers, the color uniformity is an important factor during the stage of development and mass production. Currently the color uniformity is measured manually using densitometers and the data is analyzed by inspectors to evaluate the performance. In this paper a new method of estimating the color uniformity using scanners and average brightness is presented. The color uniformity of printouts is estimated by using the test pattern and commercially available scanner. It is shown from experiments that the estimated data are similar to the data measured by densitometers. Also, with the analysis of the color uniformity, the usefulness of the proposed approach is presented.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.1
• /
• pp.51-56
• /
• 2006

A computer code was developed to simulate both the thermal stresses introduced during the post-filling stage and the in-plane deformation after ejection process by finite element method based on the plane stress theory. The computer simulation was applied to the mold design of a 2 inch light guide plate (LGP) for thin film transistor (TFT)-liquid crystal displays (LCD). With injection molding experiments based on the design of experiments (DOE) technique, the influences of the processing conditions in injection molding on brightness and uniformity of the LGP were investigated, and the optimal processing parameters were selected to increase the brightness and uniformity. The verification experiment showed that the brightness and uniformity of the LGP were increased dramatically under the selected optimal processing conditions.

• Laser Solutions
• /
• v.11 no.1
• /
• pp.1-6
• /
• 2008

We proposed new light guide panel (LGP) fabrication method exploiting laser-processed inner scatterers and surface pattern. The proposed method has achieved LGP performance improvement in both brightness and uniformity. The inner scatterers and surface pattern of grid type were fabricated with a 2nd harmonic Nd:YAG pulse laser engraving system and a $CO_2$ laser scanning system, respectively. In the implementation of LGP, inner scatterers was arranged in accordance with linear or curved pattern with changing density and surface pattern was engraved on the surface of an inner-scatterers embedded LGP. The increase of scatterers' density and the use of surface patterns in both linear and curved pattern provided high luminance and uniformity enhancement. While thecurved pattern incorporated with increased scatterers' density and surface patterns yielded brightness improvement with preserving good uniformity, the linear pattern showed highly localized brightness near the light entrance of the LGP. We can also observe that the uniformity was mainly determined by pattern of inner scatterers, and the brightness was improved by the higher density and the utilization of surface patterns. From the results, the use of laser-processed inner and surface patterns can be a potential alternative for efficient and simple LGP fabrication method.

• Laser Solutions
• /
• v.10 no.1
• /
• pp.29-34
• /
• 2007

We propose a novel application of laser engraving to patterning of light guide panel (LGP) for backlight. The feasibility of three-dimensional engraved pattern in the LGP was verified by measuring brightness and uniformity. To improve the overall uniformity, we have modified proposed patterns and found improved design for patterns. The tailoring of pattern by using laser engraving method could endow the controllability of uniformity. The proposed LGPs are more efficient in both average brightness and uniformity of illumination than the conventional LGPs which have surface pattern on the panel.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.1100-1103
• /
• 2001

(1) By comparing and analyzing the distribution of brightness as domestic lamps and Japanese products go thinner and lighter, we set an effective design standard. (2) By comparing and analyzing the feature, brightness, chromaticity and uniformity of domestic LGPs and Japanese products, early home-manufacturing and stabilization in home-manufacturing are possible. (3) By comparing and analyzing the distribution of brightness as sheets are varied, we can design an ideal sheet composition.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.493-494
• /
• 2008

LGP for the small size exit was designed and fabricated. Pattern design method, which is the most important thing in the design of the LGP, was converted from the line type into the cross type. By using this new method, the brightness unevenness, which was very difficult problem to be solved in V-cutting method, was improved. Currently products had 78% of the brightness uniformity but newly developed product in this research had 87% of the brightness uniformity. Also the optimized design rule provided the improvement of the brightness of the LGP developed in this study, that has brightness of $871cd/m^2$ whichwas 98% higher than the common products.