• 제목/요약/키워드: Circularity test

검색결과 15건 처리시간 0.02초

원호검사법을 이용한 진원도 측정 방법의 개선에 관한 연구 (A Study on the Improvement of Circularity Measurement Using Circular Test Method)

  • 이승수;김민주;전언찬
    • 한국공작기계학회논문집
    • /
    • 제11권2호
    • /
    • pp.24-29
    • /
    • 2002
  • A study for the circularity of machine tool is classified into two ways. One is to measure the circularity of machine tool by a existing measuring device. The other is to measure the circularity by remodeling the existing measuring device. We will improve on measurement of circularity using circular test method by a two-dimensional probe and a master ring for machining tools and investigate influence of trigger method, acceleration data sampling.

국내산 흑연의 구형화에 미치는 로터 속도의 영향 (The Effect of Rotor Speed on the Circiuarity of Domestic Graphite)

  • 이준섭;임유진;유경근;박현규
    • 자원리싸이클링
    • /
    • 제31권6호
    • /
    • pp.66-72
    • /
    • 2022
  • 국내산 인상흑연정광의 리튬이온전지 소재로서 활용을 위해 고강도 혼합기를 이용하여 구형화 실험 후 건식분급을 진행하여 각 산물에 대한 구형화도와 입도를 분석하였다. 3,000 rpm의 로터속도에서는 정광시료와 산물의 입도와 구형화도의 차이가 관찰되지 않았으나, 로터속도를 6,000 rpm, 10,000 rpm 12,000 rpm으로 조절하여 구형화도 실험을 진행한 결과, 로터속도와 구동시간의 증가에 따라 구형화도는 증가하고 입도는 감소하였다. 로터속도 12,000 rpm에서 10분간 구동한 결과, 구형화도는 0.870으로부터 0.936까지 증가하였다. 구형화실험 후 건식분급을 진행하였을 때 조립자의 구형화도는 0.947까지 증가하였고 SEM 결과에서 구형입자가 확인되어 구형화가 성공적으로 이루어졌다고 판단되었다.

고속가공기용 고추력 리니어모터 이송계의 특성 평가 (Characteristic Test of High Force Linear Motor Feed Unit for High Speed Machine Tool)

  • 송창규;황주호;박천홍;이후상;정재한
    • 한국정밀공학회:학술대회논문집
    • /
    • 한국정밀공학회 2000년도 춘계학술대회 논문집
    • /
    • pp.977-981
    • /
    • 2000
  • Direct drive linear motors have large potential for use as high speed machine tool feed units since they can increase machining rates and improve servo accuracy by eliminating gear related machining problems. So, in this paper, characteristic of 2-axis linear motor feed unit are studied and control gain are adjusted considering positioning, velocity, acceleration and static stiffness. We confirm linear motor feed unit are affected value of control gain sensitively, because drive directly. From the experiment, this feed unit has l${\mu}{\textrm}{m}$ micro step resolution, 5.7${\mu}{\textrm}{m}$ positioning accuracy and under 60${\mu}{\textrm}{m}$ circularity.

  • PDF

SCM계 기어의 열처리 효과에 관한 연구 (A Study on the Heat Treatment Effect of SCM Series Gear)

  • 안민주;안인효;장기;류성기
    • 한국기계가공학회지
    • /
    • 제10권2호
    • /
    • pp.84-89
    • /
    • 2011
  • This paper studied the carburizing of chromium molybdenum steel which the heat treatment effect of gear geometric tolerance, OPD, Runout, the surface hardness, the maximum hardness, the core hardness and the bending fatigue strength were investigated. Firstly, the deformation is observed, and the results of circularity, squareness, OPD and Runout of SCM822, SCM425, and SCM415 are obtained in order. Secondly, in order to investigate the gear hardness, the surface hardness, the maximum hardness and the core hardness of SCM822, SCM425, and SCM415 are obtained; and the surface hardness of SCM822 is about 10% higher than SCM415's, and about 3% higher than SCM425's. Thirdly, the fatigue strength of SCM822 is about 10% higher than SCM415's, and about 7% higher than SCM425's in the fatigue test results. At last, for the purpose of the minimum deformation of heat treatment, and also the improvement of fatigue strength, the best gear material is SCM822 in this test.

Investigating meso-scale low-temperature fracture mechanisms of recycled asphalt concrete (RAC) via peridynamics

  • Yuanjie Xiao;Ke Hou;Wenjun Hua;Zehan Shen;Yuliang Chen;Fanwei Meng;Zuen Zheng
    • Computers and Concrete
    • /
    • 제33권5호
    • /
    • pp.605-619
    • /
    • 2024
  • The increase of reclaimed asphalt pavement (RAP) content in recycled asphalt concrete (RAC) is accompanied by the degradation of low-temperature cracking resistance, which has become an obstacle to the development of RAC. This paper aims to reveal the meso-scale mechanisms of the low-temperature fracture behavior of RAC and provide a theoretical basis for the economical recycling of RAP. For this purpose, micromechanical heterogeneous peridynamic model of RAC was established and validated by comparing three-point bending (TPB) test results against corresponding numerical simulation results of RAC with 50% RAP content. Furthermore, the models with different aggregate shapes (i.e., average aggregates circularity (${\bar{C_r}}=1.00$, 0.75, and 0.50) and RAP content (i.e., 0%, 15%, 30%, 50%, 75%, and 100%) were constructed to investigate the effect of aggregate shape and RAP content on the low-temperature cracking resistance. The results show that peridynamic models can accurately simulate the low-temperature fracture behavior of RAC, with only 2.9% and 13.9% differences from the TPB test in flexural strength and failure strain, respectively. On the meso-scale, the damage in the RAC is mainly controlled by horizontal tensile stress and the stress concentration appears in the interface transition zone (ITZ). Aggregate shape has a significant effect on the low-temperature fracture resistance, i.e., higher aggregate circularity leads to better low-temperature performance. The large number of microcracks generated during the damage evolution process for the peridynamic model with circular aggregates contributes to slowing down the fracture, whereas the severe stress concentration at the corners leads to the fracture of the aggregates with low circularity under lower stress levels. The effect of RAP content below 30% or above 50% is not significant, but a substantial reduction (16.9% in flexural strength and 16.4% in failure strain) is observed between the RAP content of 30% and 50%. This reduction is mainly attributed to the fact that the damage in the ITZ region transfers significantly to the aggregates, especially the RAP aggregates, when the RAP content ranges from 30% to 50%.

BTA드릴의 절삭 기구와 마모 특성에 관한 연구 (A Study on Cutting Mechanism and Wear Character for BTA Drill)

  • 장성규;전언찬
    • 한국정밀공학회:학술대회논문집
    • /
    • 한국정밀공학회 1995년도 추계학술대회 논문집
    • /
    • pp.105-108
    • /
    • 1995
  • So far,in deep drilling process there are several manufacturing problems such as hole deviation, hole over size, circularity,straightness and surface roughness. Whit regard to these problems, we atudied the abrasion process on carbided tip of BTA drill and got the follow test results through the abrasion characteristic test and analysis on cutting mechanism for the drill tooth and guide pad. 1) In SM55C drilling process, the most stable and reasonable drilling speed range for optmum abrasion characteristic of drill tooth was 60m.min. 2) The total drilling torque was about 60kg .deg.cm on condition drilling speed 60m/min and 0.15mm/rev. These results show that the theoretical burnising torque is well accord with the tested torque which is working on guide pad.

  • PDF

CT법을 이용한 진원도 측정 방법의 개선에 관한 연구 (A Study on the Improvement of Circularity Measurement Using Circular Test Method)

  • 주만식
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
    • /
    • pp.446-451
    • /
    • 1999
  • A study for the roundness of machining center is classified into two ways. one is the way that progresses the roundness amending the parameter of machining center based on the measured value after the measurement of the roundness of machining center by means of a existing measuring device, another is the way that measures the roundness by remodeling the existing measuring device. The former is studied by pack hei jae team in Seoul university, the latter is studied by TSUTSUMI. Especially TSUTSUMI measures the roundness according to circular compensation after the insertion of developed measuring desire using a rotary encoder to the spindle of machining tool. We study how regulation velocity occuring with circular motion of machining center table influences the roundness after measuring the roundness using Circular Test method by a 2 dimention probe and a standard discus in this experiment.

  • PDF

CT법을 이용한 진원도 및 직각도 측정에 관한 연구 (A Study on the Measurement of Circularity and Perpendicularity Using Circular Test Method)

  • 주만식
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
    • /
    • pp.75-81
    • /
    • 2000
  • This study for the roundness and perpendicularity of machining center is classified into two ways. One is the way that progresses the roundness amending the parameter of machining center based on the measured value after the measurement of the roundness of machaning center by means of a existing measuring device, another is the way that measures the roundness by remodeling the existing measuring device. the former is studied by pack hei jae team in Seoul university, the later is studied by TSUTSUMI. Especially TSUTSUMI measures the roundness according to circular compensation after the insertion of developed measuring device using a rotary encoder to the spindle of machining tool. we study how regulation velocity occuring with circular motion of machining center table influences the roundness after measuring the roundness using Circular Test method by a 2 dimention probe and a standard discus in this experiment.

  • PDF

병렬기구 공직기계의 머신시뮬레이션 및 가공정밀도 평가 (The Evaluation of Machining Accuracy and the Machine Simulation for Parallel Kinematic Machine Tool(PKMT))

  • 신혁;유한식;고해주;정윤교
    • 한국기계가공학회지
    • /
    • 제8권4호
    • /
    • pp.41-47
    • /
    • 2009
  • This research deals with evaluation of machining accuracy for Parallel Kinematic Machine Tool(PKMT) applied parallel type robot system with high precision and stiffness. For this purpose, machine simulation is carried out to foreknow collision and interference between workpiece and tool. Furthermore, on the basis of machine simulation data, PKMT is manufactured. Machining accuracy such as cylindricity straightness, squareness, parallelism circularity, concentricity pitch error and yaw error, is measured by using coordinate measuring machine. Test piece for evaluation of machining accuracy is designed and manufactured under the standard of ISO 10791-7.

  • PDF

디지탈 래디오 그래피 영상에서의 흉부 노듈 검출에 관한 연구 (A Study on the Lung Nodule Detection in Digital Radiographic Images)

  • 고석빈;김종효
    • 대한의용생체공학회:의공학회지
    • /
    • 제10권1호
    • /
    • pp.1-10
    • /
    • 1989
  • An automatic lung nodule detection algorithm was applied for digital radiographic images using Bit Slice Processor. In this algorithm, signal enhancing filtering and signal suppressing filtering were performed on the given digital chest image, respectively. Then we grit the dirt- frrence image from these filtered images, and hi-level island images were obtained by applying various threshold values. From the island images, we decided the suspicious nodules using size and circularity test, and marked them to alert radiologists. The performance of the atgorithm was analyzed with respect to the size, contrast and position of digitally synthesized nodules. This method presented 45.8% of true positive ratio for the nodules of lOw in diameter with 12-16 pixel value differnces.

  • PDF