• Bulletin of the Korean Chemical Society
• /
• v.30 no.10
• /
• pp.2249-2252
• /
• 2009

The clay-based Fe-bearing catalyst was successfully prepared through ion-exchange reaction and applied as heterogeneous catalyst for discoloration of acid fuchsine (AF) in an aqueous solution by Fenton-like reaction. Experimental results demonstrated that the AF discoloration ratios increased by increasing Fe-loaded clay dosage and initial $H_2O_2$ concentration, and by decreasing the pH, respectively. The lower the initial AF concentration, the shorter the reaction time needed to achieve complete discoloration of AF. Comparative studies indicated that AF discoloration ratios were much higher in presence of Fe-loaded clay and $H_2O_2$ than those in presence of $H_2O_2$, raw natural clay or Fe-loaded clay only and raw natural clay and $H_2O_2$ jointly. After AF discoloration, there existed no new phases in the clay samples detected by XRD and no change in the clay crystal morphology observed by SEM. A mechanism proposed suggested adsorption and Fenton-like reaction were responsible for discoloration of AF.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.5
• /
• pp.1643-1646
• /
• 2012

Three Ni-based catalysts with different clay as support were prepared and tested in the hydrogenation of maleic anhydride, among which Ni/clay1 showed best activity and selectivity. Over Ni/clay1 catalyst prepared by impregnation method, 97.14% conversion of maleic anhydride and 99.55% selectivity to succinic anhydride were obtained at $180^{\circ}C$ under a pressure of 1 MPa. Catalytic activity was greatly influenced by the temperature and weighted hourly space velocity. Catalyst deactivation studies showed that this catalyst have a long life time, the yield of MA still higher than 90% even after a reaction time of 60 h. X-ray diffraction (XRD) and $H_2$ temperature programmed reduction (TPR) were use to investigate the properties of the catalyst. XRD and TPR studies showed that Ni was present as $Ni^{2+}$ on the support, which indicated that there was no elemental nickel ($Ni^0$) and $Ni_2O_3$ in the unreduced samples. The formation of Ni was strong impact on catalytic activity.

• Journal of Power System Engineering
• /
• v.19 no.4
• /
• pp.30-35
• /
• 2015

The purpose of this study is to identify the low temperature performance and strength characteristics of V-based extruded homogeneous SCR. The extruded catalyst and the coated catalyst showed 50% and 27% of NOx conversion performance respectively at about $210^{\circ}C$ of catalyst temperature, so the extruded SCR was higher in de-NOx performance than the coated SCR especially at a low temperature zone. The compressive strength of the Enhanced Extrusion #1, in which the content of promoters such as silica, clay, glass fiber and binder was optimized, was a 120% improvement compared to the Extrusion#1 catalyst, higher than the coated SCR.

• Environmental Engineering Research
• /
• v.25 no.2
• /
• pp.186-196
• /
• 2020

Pillared clays with Zr and Fe/Cu/Zr polycations have been prepared from natural clays found in large deposits of Kazakhstan and assessed as catalysts for the catalytic wet peroxide oxidation (CWPO), using 4-nitrophenol (4-NP) as model compound. The performance of the catalysts was followed by measuring the concentration of 4-NP, H₂O₂ and the total organic carbon (TOC), considering C_4-NP = 5 g L^-1, $C_{H_2O_2}$ = 17.8 g L^-1, C_cat = 2.5 g L^-1, initial pH = 3.0 and T = 50℃. At those selected conditions, the pillared clays showed higher activity than natural clays in the CWPO of 4-NP. The conversion of the model pollutant was complete when Fe/Cu/Zr-PILCs were used, with the TOC removal reaching 78.4% after 24 h with the best Fe/Cu/Zr-PILC. The H₂O₂, 4-NP and TOC time-evolution was well described by a kinetic model based on TOC lumps in three blocks, considering the initial TOC (corresponding to 4-NP), the production of oxidizable intermediates and the formation of refractory products.