• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.1A
• /
• pp.77-83
• /
• 2004

Parallel coupled microstrip bandpass filter is widely used in microwave circuits. But this filter limits the filter applications because of the narrow bandwidth and the spurious passband at twice the basic passband frequency. In order to solve this problem, a method of the asymmetrical coupled microstrip lines on composite dielectric substrate is presented. Closed form method is used to analyze the asymmetrical coupled microstrip lines on composite dielectric substrate. An experimental filter is fabricated over $33\%$ bandwidth centered at 9GHz. Compared with the filter on a single substrate, this filter on composite substrate shows improvement of the spurious passband.

• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.989-994
• /
• 1995

Rigid porous carbon fiber composites with the uniform pore size distribution were prepared by vacuum forming from water slurries containing carbonized PAN fibers, a phenolic resin and ceramic binders. The composites were designed to use for highly efficient carbon fiber filters for particulate filtration and gas adsorption. As the as-received carbon fibers of 1mm in length were milled to an approximate average length of 300${\mu}{\textrm}{m}$, modulus of rupture (MOR) of the composite filter was increased from 1MPa to the value larger than 5 MPa. Modulus of rupture (MOR) for the composite filter fabricated using the milled carbon fiber was increased from 5 MPa to 10 MPa as the carbonization temperature of the PAN fiber was raised from 90$0^{\circ}C$ to 140$0^{\circ}C$. The air permeability and an average pore size of the composite filter were increased from 40 to 270cc/min.$\textrm{cm}^2$ and from 35 to 80${\mu}{\textrm}{m}$, respectively, as the apparent porosity increased from 80 to 95%. It was shown that the MOR of the carbon fiber composite filter was dependent primarily on the average length of carbon fiber, carbonization temperature and the type of bonding materials.

• Journal of the Korean Society of Radiology
• /
• v.11 no.2
• /
• pp.69-77
• /
• 2017

This paper proposes a composite filter for noise reduction of image. To improve the image quality by reducing the noise in the liver ultrasound image, we tried to help the accurate image analysis. In the experiment, the top seven composite filters were selected by combining the Gaussian blur filter, the sharpening filter, and the median filter using the ATS-539 ultrasonic phantom, and applied to the ultrasound image in which this was done. As a result, it was found that the values of SNR, CNR and MSR all increased when the top seven composite filters were applied. In addition, PSNR of more than 30 dB, close to SSIM 1 showed that the image loss rate is small. Therefore, the appropriate application of the proposed composite filter in this research will be useful for accurate video reading and analysis.

• Composites Research
• /
• v.35 no.3
• /
• pp.216-221
• /
• 2022

Recently, the worldwide demand for disposable masks has increased due to COVID-19 infections and severe air pollution. Personal masks should reduce breathe resistance while maintaining filtering performance. In this study, a solution blowing process is used to produce composite nanofiber filters to co-spin two polymers at once. The manufacture process of the various fiber diameter filter was designed, and the filtration performance and differential pressure of the prepared filter was investigated. Poly vinylidene fluoride-hexafluoropropylene (PVDF-HFP) and Polylactic acid (PLA) fibers were chosen to be entangled together in a layer with a diameter of 1.05 ㎛ and 0.33 ㎛. Composite nanofilters showed up to 87% filtration efficiency and 32 Pa differential pressure.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.46 no.3
• /
• pp.44-51
• /
• 2009

This paper addresses a face verification method using the nonlinear composite filter. This face verification process can be simple and speedy because it does not require any reprocessing such as face detection, alignment or cropping. The optimum nonlinear composite filter is derived by minimizing the output energy due to additive noise and an input scene while maintaining the outputs of training images constant. The filter is equipped with the discrimination capability and the robustness to additive noise by minimizing the outputs of the input scene and the noise, respectively. We build the nonlinear composite filter with two training images and compare the filter with the conventional synthetic discriminant function (SDF) filter. The receiver operating characteristics (ROC) curves are presented as a metric for the performance evaluation. According to the experimental results the optimum nonlinear composite filter is shown to be a robust scheme for face verification in low resolution and noise environments.

• Journal of electromagnetic engineering and science
• /
• v.7 no.2
• /
• pp.83-90
• /
• 2007

In this paper, the formulation of the protection ratio based upon a composite fade margin and availability is newly presented for the detailed planning of frequency coordination in the microwave relay system network, and computed results for co-channel and adjacent channel protection ratios are illustrated over an actual system with 6.2 GHz. It is shown that the protection ratio to assure a quality of service can be expressed in terms of the composite fade margin, noise-to-interference ratio, net filter discrimination, and system parameters. In addition, the net filter discrimination, depending upon the transmitter spectrum mask and the overall receiver filter characteristic, has been examined to investigate the effect of the adjacent channel protection ratio caused by the adjacent channel interference. Regarding simulated results for 6.2 GHz, 60 km, 64-QAM, and N/I=6 dB at the bit error rate of $10^{-6}$, composite fade margin and co-channel protection ratio yield 25.14 and 50.3 dB, respectively. Also, the net filter discrimination of 26.5 dB and the adjacent channel protection ratio of 23.8 dB are obtained at the first adjacent channel of 30 MHz. The proposed method provides some merits in view of a comprehensive and practical application with more detailed and various system parameters needed to access the criteria for making the proper frequency coordination.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.867-868
• /
• 2008

In this paper, we discuss face verification using the optimum nonlinear composite filter. The optimum nonlinear composite filter is derived by minimizing the output energy due to the additive noise and the input scene. We construct the nonlinear composite filter with 3 training images. The performance is analyzed in terms of the detection probability and the false alarm probability showing the robustness to distortion and noise.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.4
• /
• pp.582-588
• /
• 2012

In this paper, a highly miniaturized and performed UWB bandpass filter has been newly designed and implemented by embedding all the passive elements into a multi-layered PCB substrate with high dielectric $SrTiO_3$ composite film for 3.1 - 4.75 GHz compact UWB system applications. The high dielectric composite film was utilized to increase the capacitance densities and quality factors of capacitors embedded into the PCB. In order to reduce the size of the filter and avoid parasitic EM coupling between the embedded filter circuit elements, it was designed by using a $3^{rd}$ order Chebyshev circuit topology and a capacitive coupled transformation technology. Independent transmission zeros were also applied for improving the attenuation of the filter at the desired stopbands. The measured insertion and return losses in the passband were better than 1.68 and 12 dB, with a minimum value of 0.78 dB. The transmission zeros of the measured response were occurred at 2.2 and 5.15 GHz resulting in excellent suppressions of 31 and 20 dB at WLAN bands of 2.4 and 5.15 GHz, respectively. The size of the fabricated bandpass filter was $2.9{\times}2.8{\times}0.55(H)mm^3$.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.3
• /
• pp.371-380
• /
• 2004

In the dust separation by using porous filter media, the structure of dust layer deposited on the filter surface of filter medium directly affects the effective filtration. The present study has investigated the specific resistance (K$_2$') of the dust layer and its porosity ($\varepsilon$$_{c}$) for three different filters; FA composite filter, metal fiber filter and stainless filter. The specific resistance (K$_2$') increased and at the same time the cake porosity ($\varepsilon$$_{c}$) decreased with the increase of filtration velocity, possibly due to the compressible effect of dust layer. However, under the low dust concentration, subsequent dust particles would block the open channels through the layer resulting in high specific resistance of the layer. The FA composite filter among three filters was shown to be the most effective filter for dust cake filtration at low filtration velocities less than 0.1 m/s for an approximate dust concentration of 5 g/㎥.

• Journal of Advanced Navigation Technology
• /
• v.15 no.4
• /
• pp.571-577
• /
• 2011

This paper presents a novel balanced filter design based on a metamaterial structure applicable to differential-mode excitation. The metamaterial structure is based on a unit-cell which under a differential-mode excitation behaves like composite right/left-handed(CRLH) metamaterial with filter characteristics. In contrast, the metamaterial unit-cell is below cut-off under a common-mode excitation. Experimental results are used to verify the proposed metamaterial's differential-mode characteristics. The metamaterial is fabricated with a balanced filter design resulting in an operating frequency range of 960~1000 MHz with a insertion loss of 4.1 dB.