• Journal of Powder Materials
• /
• v.21 no.6
• /
• pp.415-421
• /
• 2014

W-10vol.%ZrC composites reinforced by micrometric and nanosized ZrC particles were prepared by hot-pressing of 25 MPa for 2 h at $1900^{\circ}C$. The effect of ZrC particle size on microstructure and mechanical properties at room temperature and elevated temperatures was investigated by X-ray diffraction analysis, scanning electron microscope and transmission electron microscope observations and the flexural strength test of the W-ZrC composite. Microstructural analysis of the W-ZrC composite revealed that nanosized ZrC particles were homogeneously dispersed in the W matrix inhibiting W grain growth compared to W specimen with micrometric ZrC particle. As a result, its flexural strength was significantly improved. The flexural strength at room temperature for W-ZrC composite using nanosized ZrC particle being 740 MPa increased by around 2 times than that of specimen using micrometric ZrC particle which was 377 MPa. The maximum strength of 935 MPa was tested at $1200^{\circ}C$ on the W composite specimen containing nanosized ZrC particle.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.201-202
• /
• 2002

The abrasive wear behaviour of $Al_2O_3$ particle-reinforced aluminium composite was investigated. The wear rate of the composite and the matrix alloy has been expressed in terms of the applied load, sliding distance and particle size using linear factorial design approach.

• Advances in materials Research
• /
• v.1 no.3
• /
• pp.169-182
• /
• 2012

In this paper the intrinsic influence of micron-sized nickel particle reinforcements on microstructure, micro-hardness tensile properties and tensile fracture behavior of nano-alumina particle reinforced magnesium alloy AZ31 composite is presented and discussed. The unreinforced magnesium alloy (AZ31) and the reinforced nanocomposite counterpart (AZ31/1.5 vol.% $Al_2O_3$/1.5 vol.% Ni] were manufactured by solidification processing followed by hot extrusion. The elastic modulus and yield strength of the nickel particle-reinforced magnesium alloy nano-composite was higher than both the unreinforced magnesium alloy and the unreinforced magnesium alloy nanocomposite (AZ31/1.5 vol.% $Al_2O_3$). The ultimate tensile strength of the nickel particle reinforced composite was noticeably lower than both the unreinforced nano-composite and the monolithic alloy (AZ31). The ductility, quantified by elongation-to-failure, of the reinforced nanocomposite was noticeably higher than both the unreinforced nano-composite and the monolithic alloy. Tensile fracture behavior of this novel material was essentially normal to the far-field stress axis and revealed microscopic features reminiscent of the occurrence of locally ductile failure mechanisms at the fine microscopic level.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.7
• /
• pp.447-452
• /
• 1987

In this paper, the dependence of piezoelectric properties in the 0-3 composite system of piezoelectric-ceramics polymer materials on particle size of ceramics were investigated. Radial mode and thickness mode of composite were observed similar to single phase of piezoelectric ceramics. The measured values of dielectric constant and dissipation factor were dependent on particle size, which increased with the increasing particle size. the planar coupling factor, thickness coupling factor and thickness frequency constant with the particle size were almost constant, while planar frequency constant increased. The thickness coupling factor decreased with the increasing thickness of specimen. It is found that maximum voltage coeffidient was calculated on the specimen with particle size smallar than 46 ${\mu}m$.

• Polymer(Korea)
• /
• v.25 no.5
• /
• pp.617-624
• /
• 2001

The core-shell composite latexes were synthesized by stage emulsion polymerization of methyl methacrylate (MMA) and styrene (St) with ammonium persulfate after preparing monomer pre-emulsion in the presence of anionic surfactant. However, in preparation of core-shell composite latex, several unexpected results are observed, such as, particle coagulation, low degree of polymerization, and formation of new particles during shell polymerization. To solve the disadvantages, We study the effect of initiator concentrations, surfactant concentrations, and reaction temperature on the core-shell structure of polymethyl methacrylate/polystyrene and polystyrene/polymethyl methacrylate. Particle size and particle size distribution were measured using particle size analyzer, and the morphology of the core-shell composite latex was determined using transmission electron microscope. Glass temperature was also measured using differential scanning calorimeter. To identify the core-shell structure, pH of the two composite latex solutions were measured.

• Journal of Welding and Joining
• /
• v.22 no.5
• /
• pp.46-52
• /
• 2004

AlSi-Al$_2$O$_3$ composite layer was prepared by plasma spray on steel substrate. The composite powder for plasma spray was prepared by simple mechanical blending. The wear resistance of the composite layers and matrix aluminum alloy were performed in terms of size distribution of ceramic particles. Friction coefficients of AlSi were decreased with incorporation of $Al_2$O$_3$. The tribological properties of coated layers were affected by the size of incorporated $Al_2$O$_3$ particle. The reinforcement of $Al_2$O$_3$ particle into aluminum alloy matrix decreased the friction coefficient as well as wear loss.

• Journal of Mechanical Science and Technology
• /
• v.15 no.6
• /
• pp.727-734
• /
• 2001

The Tribological evaluation of commercial dental composite resins containing prepolymerized particle fillers was investigated. Composite resins such as Metafil, Silux Plus, Heliomolar, and Palfique Estelite were selected as specimens. In the wear tests, a ball-on-flat wear test method was used. The friction coefficient of Metafil was quite high. The wear resistance of Silux Plus and Palfique Estelite was better than that of Metafil and Heliomolar under the same experimental conditions. The main wear mechanism of the composite resins containing prepolymerized particle fillers was abrasive wear caused by the brittle fracture of the prepolymerized particles and the debonding of the filler and the matrix.

• Journal of the Korean Ceramic Society
• /
• v.37 no.3
• /
• pp.227-232
• /
• 2000

The LSM-YSZ composite electrode as a mixture of LSM and YSZ shows percolation characteristics. It was identified that the polarization resistance of LSM-YSZ composite electrode depend on YSZ connectivity by changing powder size ratio of the DLSM/DYSZ. That is, YSZ in composite electrode showed low electrochemical activity without YSZ connectivity. However, the polarization resistance decreased abruptly with YSZ connectivity due to high electrochemical activity of YSZ in composite electrode. Because the amount of three phase boundary is dependent on LSM and YSZ particle size, the polarization resistance of cathode decreases as LSM and YSZ particle size decreases.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.237-239
• /
• 2002

The effect of particle sizes of the metal matrix composites containing 10 wt.%SiCp was investigated with using various tools. The results showed that tool life decreased considerably with increasing particle size and cutting speed. The wear resistance of TiC-coated tools was considerably higher than that of the other tools. It was observed that abrasive wear was the main responsible mechanism for wear of the tool thermal cracks were at high speed while a built-edge formation was also evident at lower speed.

• Composites Research
• /
• v.26 no.4
• /
• pp.218-222
• /
• 2013

This study demonstrated that a slag, an industrial solid waste, can be used as a structural reinforcement. The mechanical properties(tensile strength and Elastic modulus) of slag reinforced composite(SRC) was investigated as functions of slag particle size (8~12 ${\mu}m$ and 12~16 ${\mu}m$) and volume fraction (0-40 vol.%). In order to investigate the interface and a degree of particle dispersion which have an effect on mechanical properties, optical microscopic images were taken. The results of tensile tests showed that the tensile strength decreased with an increase in slag volume fraction and particle size. The elastic modulus increased with an increase in slag volume fraction and particle size except for 30 vol.% SRC. The tensile strength decreased with an increase in slag particle size. The microscopic picture showed SRC has fine degree of particle dispersion at low slag volume fraction. SRC has a good interface at every volume fraction. However particle cluster was incorporated with an increase in slag volume fraction.